Device type:
Search:
| Brand | Device | Product Number | Device type | Protocol | Driver or app name | Instructions | Buy it |
|---|---|---|---|---|---|---|---|
| 2GIG | 700 Series Smart Thermostat | STZ-1 | Thermostat | Z-Wave | Generic Z-Wave Plus Thermostat | Show | |
| ADT (Nortek) | Water Leak Detector | 10016864C | Water Sensor | Zigbee | Generic Zigbee Moisture Sensor | Show | Amazon |
| AduroSmart | ERIA Contact Sensor | 81822 | Contact Sensor | Zigbee | ERIA Contact Sensor | Show | Amazon |
| AduroSmart | ERIA Dimmer Switch | 81825 | Button Controller | Zigbee | ERIA Dimmer Switch | Show | Amazon |
| AduroSmart | ERIA Motion Sensor | 81823 | Motion Sensor | Zigbee | ERIA Motion Sensor | Show | Amazon |
| AduroSmart | RGBW Bulb | AD-RGBW3001 | Bulb | Zigbee | Advanced Zigbee RGBW Bulb | ||
| Aeotec (Aeon Labs) | Aeotec Outdoor Smart Plug | ZWA042 | Outlet / Plug | Z-Wave | Aeotec Outdoor Smart Plug | ||
| Aeotec (Aeon Labs) | Aeotec Panic Button | DSA38 | Button Controller | Z-Wave | Aeotec Panic Button | Show | |
| Aeotec (Aeon Labs) | aërQ Temperature & Humidity Sensor | ZWA009 | Temperature Sensor | Z-Wave | Aeotec aerQ | Show | Amazon |
| Aeotec (Aeon Labs) | Contact Sensor | DSB04100 | Contact Sensor | Z-Wave | Generic Z-Wave Contact Sensor | Show | |
| Aeotec (Aeon Labs) | Door Window Sensor 6 | ZW112 | Contact Sensor | Z-Wave | Generic Z-Wave Contact Sensor | Show | |
| Aeotec (Aeon Labs) | Door Window Sensor 7 | ZWA008-A | Contact Sensor | Z-Wave | Aeotec Door/Window Sensor 7 | Show | |
| Aeotec (Aeon Labs) | Door/Window Sensor 7 Basic | Contact Sensor | Z-Wave | Aeotec Door/Window Sensor 7 Series | Show | ||
| Aeotec (Aeon Labs) | Door/Window Sensor 7 Pro | AEOEZWA012 | Contact Sensor | Z-Wave | Aeotec Door/Window Sensor 7 Series | Show | Amazon |
| Aeotec (Aeon Labs) | Door/Window Sensor 7 Series | DWS7 | Contact Sensor | Z-Wave | Aeotec Door/Window Sensor 7 Series | Show | |
| Aeotec (Aeon Labs) | Door/Window Sensor Gen 2 | DSB29 | Contact Sensor | Z-Wave | Generic Z-Wave Contact Sensor | Show | |
| Aeotec (Aeon Labs) | Doorbell | ZW056 | Doorbell | Z-Wave | Aeon Labs Doorbell | Show | |
| Aeotec (Aeon Labs) | Doorbell 6 | ZW162-A | Doorbell | Z-Wave | Aeotec Siren 6 New | Show | |
| Aeotec (Aeon Labs) | Dry Contact Sensor | ZW097-A | Contact Sensor | Z-Wave | Generic Z-Wave Contact Sensor | Show | |
| Aeotec (Aeon Labs) | Dual Micro Switch | DSC17 | Switch | Z-Wave | Aeotec Dual Micro Switch | ||
| Aeotec (Aeon Labs) | Dual Nano Switch | ZW132 | Switch | Z-Wave | Aeotec Dual Nano Switch | Show | Amazon |
| Aeotec (Aeon Labs) | Garage Door Controller Gen 5 | Garage Door Controller | Z-Wave | Generic Z-Wave Garage Door Opener | Show | ||
| Aeotec (Aeon Labs) | Home Energy Meter | AEDSB09104ZWUS | Energy Meter | Z-Wave | Aeon Home Energy Meter | Show | |
| Aeotec (Aeon Labs) | Illumino Dimmer Switch | ZWA037-A | Dimmer | Z-Wave | Aeotec Illumino Dimmer Switch | Show | Amazon |
| Aeotec (Aeon Labs) | Illumino Wall Switch | ZWA038-A | Switch | Z-Wave | Aeotec Illumino Wall Switch | Show | |
| Aeotec (Aeon Labs) | LED Bulb 5 | ZW098-A52 | Bulb | Z-Wave | Aeon LED Bulb | Show | |
| Aeotec (Aeon Labs) | LED Bulb 6 Multi-Color | ZWA002 | Bulb | Z-Wave | Aeotec LED Bulb 6 Multi-Color | Show | |
| Aeotec (Aeon Labs) | LED Bulb 6 Multi-White | ZWA001 | Bulb | Z-Wave | Aeotec LED Bulb 6 Multi-White | Show | |
| Aeotec (Aeon Labs) | Micro Illuminator G2 | DSC27103 | Dimmer | Z-Wave | Aeon Micro Dimmer | ||
| Aeotec (Aeon Labs) | Micro Motor Controllers | Motor Controller | Z-Wave | Aeon Motor Controller | Show | ||
| Aeotec (Aeon Labs) | Micro Switch G2 | DSC26103 | Switch | Z-Wave | Aeon Micro Switch | ||
| Aeotec (Aeon Labs) | Minimote | DSA03202 | Button Controller | Z-Wave | Aeon Minimote | Show | |
| Aeotec (Aeon Labs) | Motor Controller | Motor Controller | Z-Wave | Aeon Motor Controller | |||
| Aeotec (Aeon Labs) | MultiSensor 6 | ZW100-A | Motion Sensor | Z-Wave | Aeon MultiSensor 6 | Show | |
| Aeotec (Aeon Labs) | MultiSensor 7 | ZWA024-C | Motion Sensor | Z-Wave | Aeotec Multisensor 7 | Show | |
| Aeotec (Aeon Labs) | MultiSensor 7 | ZWA024-A | Multisensor | Z-Wave | Aeotec MultiSensor 7 | Show | |
| Aeotec (Aeon Labs) | MultiSensor Gen5 | ZW074 | Motion Sensor | Z-Wave | Aeon MultiSensor 6 | Show | |
| Aeotec (Aeon Labs) | Nano Dimmer | ZW111 | Dimmer | Z-Wave | Aeotec Nano Dimmer | Show | Amazon |
| Aeotec (Aeon Labs) | Nano Shutter | ZW141 | Motor Controller | Z-Wave | Aeotec Nano Shutter | Show | |
| Aeotec (Aeon Labs) | Nano Switch | ZW116 | Switch | Z-Wave | Aeotec Nano Switch | Show | |
| Aeotec (Aeon Labs) | Nano Switch | ZW139 | Switch | Z-Wave | Aeotec Nano Switch | Show | Amazon |
| Aeotec (Aeon Labs) | NanoMote One | ZWA003-A, ZWA004 | Button Controller | Z-Wave | Aeotec NanoMote | Show | Amazon |
| Aeotec (Aeon Labs) | NanoMote Quad | ZWA004-A | Button Controller | Z-Wave | Aeotec NanoMote | Show | |
| Aeotec (Aeon Labs) | Range Extender 6 | DSD37 | Repeater | Z-Wave | Generic Z-Wave Repeater | Show | Amazon |
| Aeotec (Aeon Labs) | Range Extender 7 | ZW189 | Repeater | Z-Wave | Generic Z-Wave Repeater | Show | Amazon |
| Aeotec (Aeon Labs) | Recessed Door Sensor | DS854-ZWUS | Contact Sensor | Z-Wave | Generic Z-Wave Contact Sensor | ||
| Aeotec (Aeon Labs) | Recessed Door Sensor 7 | ZW187-A | Contact Sensor | Z-Wave | Aeotec Door/Window Sensor 7 Series | Show | Amazon |
| Aeotec (Aeon Labs) | Recessed Door Sensor Gen 5 | ZW089 | Contact Sensor | Z-Wave | Generic Z-Wave Contact Sensor | Show | |
| Aeotec (Aeon Labs) | Siren | ZW080 | Siren | Z-Wave | Aeon Siren | Show | |
| Aeotec (Aeon Labs) | Siren 6 | ZW164-A | Siren | Z-Wave | Aeotec Siren 6 New | Show | Amazon |
| Aeotec (Aeon Labs) | Smart Energy Switch | DSC06106 | Outlet / Plug | Z-Wave | Aeotec Smart Energy Switch | Show | |
| Aeotec (Aeon Labs) | Smart Switch 6 | ZW096-A02, ZW096AU, ZW110-B09 | Outlet / Plug | Z-Wave | Aeotec Smart Switch 6 | Show | |
| Aeotec (Aeon Labs) | Smart Switch 7 US | ZWA023-A | Outlet / Plug | Z-Wave | Aeotec Smart Switch 7 US | Show | Amazon |
| Aeotec (Aeon Labs) | TriSensor | ZWA005-A | Motion Sensor | Z-Wave | Aeotec TriSensor | Show | Amazon |
| Aeotec (Aeon Labs) | WallMote 7 | ZWA022 | Button Controller | Z-Wave | Aeotec WallMote 7 | Show | |
| Aeotec (Aeon Labs) | WallMote Quad | ZW130 | Button Controller | Z-Wave | Aeon WallMote | Show | |
| Aeotec (Aeon Labs) | WallMote Quad | ZW129-A | Button Controller | Z-Wave | Aeon WallMote | Show | Amazon |
| Aeotec (Aeon Labs) | Water Sensor 7 Pro | ZWA019-C | Water Sensor | Z-Wave | Aeotec Water Sensor 7 Pro | Show | |
| AGSHome | Motion Sensor | DP-ZGMD2 | Motion Sensor | Zigbee | Generic Zigbee Motion Sensor | Show | Amazon |
| Alarm.com | T3000 Smart Thermostat | ADC-3000 | Thermostat | Z-Wave | Generic Z-Wave Plus Thermostat driver | Amazon | |
| Alfred | Z-Wave Lock | DB2, DB2-B | Lock | Z-Wave | null (app) | Show | |
| Amazon | Echo | All | Voice Assistant | Hidden | Amazon Alexa installation helper (app) | Show | Amazon |
| Aqara | Aqara Door and Window Sensor P2 | Contact Sensor | Matter | Aqara Door and Window Sensor P2 | |||
| August | August Pro Lock | Lock | Z-Wave | August Pro Z-Wave Lock | Show | Amazon | |
| Aurora | AOne Smart Double Socket | AU-A1ZBDSS | Outlet / Plug | Zigbee | Aurora Zigbee Switch | Show | |
| Aurora | AOne Smart Plug-In Socket | AU-A1ZBPIAB | Outlet / Plug | Zigbee | Aurora Zigbee Switch | Show | |
| Aurora | AOne Smart Remote | AU-A1ZBRC | Button Controller | Zigbee | Aurora Zigbee Button Controller | Show | |
| Aurora | RGBW GLS | AU-A1GSZ9RGBWE | Bulb | Zigbee | Advanced Zigbee RGBW Bulb | Show | |
| Aurora | RGBW GU10 | AU-A1GUZBRGBW | Bulb | Zigbee | Advanced Zigbee RGBW Bulb | Show | |
| Aurora | Smart dimmable GLS Lamp | AU-A1GSZ9E/27 | Bulb | Zigbee | Advanced Zigbee Bulb | Show | |
| Aurora | Smart Door / Window sensor | AU-A1ZBDWS | Contact Sensor | Zigbee | frient Contact Sensor | Show | |
| Aurora | Smart PIR Sensor | AU-A1ZBPIRS | Motion Sensor | Zigbee | frient Motion Sensor | Show | |
| Aurora | Smart Tunable GLS | AU-A1GSZ9CXE | Bulb | Zigbee | Advanced Zigbee CT Bulb | Show | |
| Aurora | Smart Tunable GU10 | AU-A1GUZBCX5 | Bulb | Zigbee | Advanced Zigbee CT Bulb | Show | |
| Aurora | Zigbee vintage G125 Lamp | AU-A1VG125Z5E/19 | Bulb | Zigbee | Advanced Zigbee Bulb | Show | |
| Aurora | Zigbee vintage GLS Lamp | AU-A1VGSZ5E/19 | Bulb | Zigbee | Advanced Zigbee Bulb | Show | |
| Aurora | Zigbee vintage ST64 Lamp | AU-A1VST64Z5E/19 | Bulb | Zigbee | Advanced Zigbee Bulb | Show | |
| Axis Labs | Gear | Gear | Shade Controller | Zigbee | Generic Zigbee Shade | Show | |
| BeSense | 360 Ceiling Sensor | IX32 | Motion Sensor | Z-Wave | BeSense Motion Sensor Zwave Plus | Show | |
| BeSense | Door/Window Sensor | IM20 | Contact Sensor | Z-Wave | Generic Z-Wave Contact Sensor | Show | |
| BeSense | PIR Wall Sensor | IX30 | Motion Sensor | Z-Wave | BeSense Motion Sensor Zwave Plus | Show | Amazon |
| Blitzwolf | water sensor | Water Sensor | Zigbee | Generic Zigbee Moisture Sensor (no temp) | |||
| Bond Home | Bond Bridge | BD-1000 | Bridge | LAN | Bond Integration (app) | Show | |
| Bosch | PIR Motion Detector | ISW-ZPR1-WP13 | Motion Sensor | Zigbee | Bosch Motion Detector | Show | |
| Bosch | TriTech Motion Detector | ISW-ZDL1-WP11G | Motion Sensor | Zigbee | Bosch Motion Detector | Show | |
| Candeo | rotary dimmer | Dimmer | Zigbee | Generic Zigbee Dimmer | |||
| CEL | Cotet Z10 Range Extender | CGW-Z-0010 | Repeater | Zigbee | Ikea TRADFRI Signal Repeater | Show | |
| Centralite | Centralite Spectrum dimmer | 3385001-ZHA | Dimmer | Zigbee | Centralite Zigbee Dimmer (spectrum) | ||
| Centralite | Contact Sensor | 3300-G | Contact Sensor | Zigbee | Generic Zigbee Contact Sensor | Show | Amazon |
| Centralite | Keypad | 3400 | Keypad | Zigbee | Centralite Keypad | Show | |
| Centralite | Micro Door Sensor | 3323-G | Contact Sensor | Zigbee | SmartSense Multi Sensor | Show | Amazon |
| Centralite | Motion Sensor | 3305-G | Motion Sensor | Zigbee | Generic Zigbee Motion Sensor | Show | |
| Centralite | Nightlight/Repeater | 3420 | Bulb | Zigbee | Generic Zigbee Bulb | Show | |
| Centralite | Pearl Thermostat | 3000-G | Thermostat | Zigbee | Generic Zigbee Thermostat | Show | |
| Centralite | Smart Outlet | 4200-C | Outlet / Plug | Zigbee | Generic Zigbee Outlet | Show | |
| Consciot | Matter Smart Light Bulb | Bulb | Matter | Generic Matter RGBW Light | |||
| Cree | Connected A-19 Bulb | Bulb | Zigbee | Generic Zigbee Bulb | Show | Amazon | |
| Current | E-Wand | E-Wand | Shade Controller | Zigbee | Generic Zigbee Shade | Show | |
| Danalock | V3 Z-Wave Lock | V3 | Lock | Z-Wave | Danalock V3 Z-Wave | Amazon | |
| Danalock | V3 Zigbee Lock | V3 | Lock | Zigbee | Generic Zigbee Lock (no keypad) | Show | |
| Denon | Audio Video Receiver | Any with Ethernet port | Audio Video Receiver | LAN | Denon AVR | Show | Amazon |
| Develco | Motion sensor 2 | MOSZB-153 | Motion Sensor | Zigbee | frient Motion Sensor Pro | Show | |
| Develco | window sensor | WISZB-131 | Contact Sensor | Zigbee | frient Contact Sensor Pro | Show | |
| Diese | Wall Touch Smart Light Switch | 1, 2, 3 and 4 button | Switch | Zigbee | Generic Zigbee Multi-Endpoint Switch | Show | |
| Dome | Door/Window Sensor | DMWD1 | Contact Sensor | Z-Wave | Dome Door Sensor | Show | Amazon |
| Dome | Door/Window Sensor Pro | DMDP1 | Contact Sensor | Z-Wave | Dome Door/Window Sensor Pro | Show | |
| Dome | Leak Sensor | DMWS1 | Water Sensor | Z-Wave | Dome Leak Sensor | Show | |
| Dome | Motion Sensor | DMMS1 | Motion Sensor | Z-Wave | Dome Motion Sensor | Show | |
| Dome | Mouser | DMMZ1 | Mouse Trap | Z-Wave | Dome Mouser | Show | Amazon |
| Dome | On/Off Plug | DMOF1 | Outlet / Plug | Z-Wave | Dome On Off Plug | Show | |
| Dome | Range Extender | DMEX1 | Repeater | Z-Wave | Dome Range Extender | Show | |
| Dome | Siren | DMS01 | Siren | Z-Wave | Dome Siren | Show | |
| Dome | Water Shutoff | DMWV1 | Valve | Z-Wave | Dome Water Shut-Off | Show | Amazon |
| Dragontech | Plug in Z-Wave Plus Dimmer Switch | PD-100 | Dimmer | Z-Wave | Generic Z-Wave Dimmer | Show | |
| Dragontech | Plug-In On/Off Z-Wave Plus Appliance Module | PA-100 | Outlet / Plug | Z-Wave | Generic Z-Wave Outlet | ||
| Eaton (Cooper Wiring Devices) | Accessory Dimmer | RF9642 | Dimmer | Z-Wave | Eaton Accessory Dimmer | Amazon | |
| Eaton (Cooper Wiring Devices) | Accessory Switch | RF9617 | Switch | Z-Wave | Eaton Accessory Switch | Show | Amazon |
| Eaton (Cooper Wiring Devices) | Dimmer | RF9540, RF9640 | Dimmer | Z-Wave | Generic Z-Wave Smart Dimmer | Show | Amazon |
| Eaton (Cooper Wiring Devices) | Master Dimmer | RF9640 | Dimmer | Z-Wave | Eaton Master Dimmer | Amazon | |
| Eaton (Cooper Wiring Devices) | Master Switch | RF9601 | Switch | Z-Wave | Eaton Master Switch | Amazon | |
| Eaton (Cooper Wiring Devices) | Plug-In Module | RF96APM | Outlet / Plug | Z-Wave | Generic Z-Wave Plus Outlet | ||
| Eaton (Cooper Wiring Devices) | Switch | RF9601 | Switch | Z-Wave | Generic Z-Wave Smart Switch | Show | Amazon |
| Eaton (Cooper Wiring Devices) | Wireless Outlet / Plug | RF96APM | Outlet / Plug | Z-Wave | Generic Z-Wave Plus Outlet | Show | |
| Ecobee | Thermostat | Thermostat | LAN | Ecobee Integration (app) | Show | Amazon | |
| Ecolink | Chime + Siren | ISZW7-ECO | Siren | Z-Wave | Ecolink Chime+Siren | ||
| Ecolink | Contact Sensor | DWZWAVE2.5-ECO | Contact Sensor | Z-Wave | Generic Z-Wave Contact Sensor | Show | Amazon |
| Ecolink | Door/Window Sensor | DWZB1-ECO | Contact Sensor | Zigbee | Generic Zigbee Contact Sensor | Show | |
| Ecolink | Ecolink TBZ500 thermostat | TBZ500 | Thermostat | Z-Wave | Generic Z-Wave Plus Thermostat | ||
| Ecolink | Flood/Freeze Sensor | FLF-ZWAVE5 | Water Sensor | Z-Wave | Generic Z-Wave Water Sensor | Show | Amazon |
| Ecolink | Garage Door Tilt Sensor | TILT-ZWAVE2 | Tilt Sensor | Z-Wave | Generic Z-Wave Contact Sensor | Show | |
| Ecolink | Garage Door Tilt Sensor | TILT-ZWAVE5 | Tilt Sensor | Z-Wave | Ecolink Garage Door Tilt Sensor (TILT-ZWAVE5) | ||
| Ecolink | Motion Sensor | PIR-ZWAVE2.5 | Motion Sensor | Z-Wave | Generic Z-Wave Motion Sensor | Show | |
| Ecolink | Pet Immune Motion Detector | PIRZB1-ECO | Motion Sensor | Zigbee | Generic Zigbee Motion Sensor | Show | Amazon |
| Ecolink | Siren | SC-ZWAVE5 | Siren | Z-Wave | Ecolink Siren | Show | Amazon |
| Ecolink | Smoke/CO Audio Detector | FF-ZWAVE5 | Smoke/CO Detector | Z-Wave | Ecolink Smoke/CO Audio Detector | Show | |
| Ecolink | Tilt Sensor | TILT-ZWAVE2.5 | Tilt Sensor | Z-Wave | Generic Z-Wave Contact Sensor | Show | Amazon |
| Ecolink | Wireless Double Rocker Switch | DDLS2-ZWAVE5 | Switch | Z-Wave | Ecolink Wireless Switch | Show | Amazon |
| Ecolink | Wireless Double Toggle Switch | DTLS2-ZWAVE5 | Switch | Z-Wave | Ecolink Wireless Switch | Show | Amazon |
| Ecolink | Wireless Rocker Switch | DLS-ZWAVE5 | Switch | Z-Wave | Ecolink Wireless Switch | Show | Amazon |
| Ecolink | Wireless Toggle Switch | TLS-ZWAVE5 | Switch | Z-Wave | Ecolink Wireless Switch | Show | Amazon |
| Enerwave | Ceiling Mounted PIR Motion Sensor | ZWN-BPC-Plus | Motion Sensor | Z-Wave | Generic Z-Wave Motion Sensor | Show | |
| Enerwave | Dual Relay | ZWN-RSM2-PLUS | Relay | Z-Wave | Generic Z-Wave Plus MultiSwitch | Amazon | |
| Enerwave | Plug-In Outlet | ZB-333 | Outlet / Plug | Zigbee | Generic Zigbee Outlet | Show | |
| ESTTECH | grow light | EST-LED-GH001 | Bulb | Zigbee | Advanced Zigbee Bulb | Show | |
| Eurotronic | Spirit TRV Thermostat | 700201 | Thermostat | Z-Wave | Eurotronic Spirit TRV Thermostat | ||
| Eva Logik | Eva Logik Dimmer | ZW31S | Dimmer | Z-Wave | Eva Logik ZW31S Dimmer | ||
| Eva Logik | In-Wall Switch | ZW30 | Switch | Z-Wave | EVA LOGIK In-Wall Switch | ||
| Eva Logik | Outdoor Plug | Outlet / Plug | Z-Wave | EVA LOGIK Smart Plug | Amazon | ||
| Eva Logik | Smart Plug | ZW36, ZW37 | Outlet / Plug | Z-Wave | EVA LOGIK Smart Plug | Show | Amazon |
| Eva Logik | Smart Plug | ZW39 | Dimmer | Z-Wave | EVA LOGIK Smart Plug Dimmer | Show | |
| Eve | Eve Door | Contact Sensor | Matter | Generic Matter Contact Sensor | |||
| Eve | Eve Energy | Outlet / Plug | Matter | Generic Matter Outlet | |||
| Eve | Eve Motion | Motion Sensor | Matter | Eve Motion | |||
| Everspring | Door/Window Detector | HSM02 | Contact Sensor | Z-Wave | Generic Z-Wave Contact Sensor | Show | |
| Everspring | Everspring Illumination Sensor | ST815 | Light Sensor | Z-Wave | Everspring Illumination Sensor | Show | |
| Everspring | Flood Detector | ST812 | Water Sensor | Z-Wave | Generic Z-Wave Water Sensor | Show | Amazon |
| Everspring | PIR Detector | HSP02 | Motion Sensor | Z-Wave | Generic Z-Wave Motion Sensor | Show | |
| Everspring | Smoke Detector | SF813 | Smoke/CO Detector | Z-Wave | Generic Z-Wave Smoke Detector | Show | |
| Everspring | Temperature/Humidity Sensor | ST814 | Temperature Sensor | Z-Wave | Generic Z-Wave Temperature/Humidity Sensor | Show | |
| Evolve | Isolated Contact Fixture Module | LFM-20 | Relay | Z-Wave | Generic Z-Wave Relay | Show | |
| EVVR | EVVR smart relay | Switch | Zigbee | Generic Zigbee switch | |||
| eWeLink | 10A Outlet | SA-003-Zigbee | Outlet / Plug | Zigbee | Generic Zigbee Outlet | Show | |
| eWeLink | Relay | 1, 2 and 4 channel relay | Relay | Zigbee | Generic Zigbee Multi-Endpoint Switch | Show | |
| Fibaro | Button | FGPB-101 | Button Controller | Z-Wave | Generic Z-Wave Button Controller | Show | Amazon |
| Fibaro | Door/Window Sensor 2 | FGDW-002 | Contact Sensor | Z-Wave | Fibaro Door/Window Sensor 2 | Show | Amazon |
| Fibaro | Fibaro Dimmer 2 | FGD-212 | Dimmer | Z-Wave | Fibaro Dimmer | Amazon | |
| Fibaro | Fibaro RGBW Controller | FGRGBW-101 | RGBW Controller | Z-Wave | Fibaro RGBW Controller | Show | |
| Fibaro | Fibaro Smart Implant | FGBS-222 | Multisensor | Z-Wave | Fibaro Smart Implant | Amazon | |
| Fibaro | Flood Sensor | FGFS-101 FG3 | Water Sensor | Z-Wave | Fibaro Flood Sensor | Show | |
| Fibaro | Flood Sensor ZW5 | FGFS-101 ZW5 | Water Sensor | Z-Wave | Fibaro Flood Sensor | Show | Amazon |
| Fibaro | KeyFob | FGKF-601 ZW5 | Button Controller | Z-Wave | Generic Z-Wave Button Controller | Show | Amazon |
| Fibaro | Motion Sensor ZW5 | FGMS-001 ZW5 | Motion Sensor | Z-Wave | Fibaro Motion Sensor ZW5 | Show | Amazon |
| Fibaro | Radiator Thermostat | FIBEFGT-001 | Thermostat | Z-Wave | Fibaro Heat Controller Thermostat Head | Show | |
| Fibaro | Single Switch 2 | FGS-213 | Switch | Z-Wave | Fibaro Switch | Show | Amazon |
| Fibaro | Universal Binary Sensor | FGBS-001 | Contact Sensor | Z-Wave | Fibaro Universal Binary Sensor | Show | |
| Fibaro | Wall Plug | FGWPB-111, FGWPB-121 | Outlet / Plug | Z-Wave | Fibaro Wall Plug | Show | Amazon |
| First Alert | Smoke & CO Alarm | ZCOMBO | Smoke/CO Detector | Z-Wave | Generic Z-Wave Smoke/CO Detector | Show | |
| First Alert | Smoke & CO Alarm | ZCOMBO Gen 2 & 3 | Smoke/CO Detector | Z-Wave | Generic Z-Wave Plus Smoke/CO Detector | Show | Amazon |
| FortrezZ | MIMO2+ | MIMO2+ | Relay | Z-Wave | Fortrezz MIMO2+ | Show | |
| FortrezZ | MIMOlite | MIMOlite | Relay | Z-Wave | FortrezZ MIMOlite | Show | |
| frient | Air Quality Sensor | AQSZB-110 | Air Quality Sensor | Zigbee | frient Air Quality Sensor | Show | |
| frient | Entry Sensor | WISZB-121 | Contact Sensor | Zigbee | frient Contact Sensor | Show | |
| frient | Entry Sensor Pro | WISZB-120 | Contact Sensor | Zigbee | frient Contact Sensor Pro | Show | |
| frient | Heat Alarm | HESZB-120 | Heat Alarm | Zigbee | frient Smoke/Heat Alarm | Show | |
| frient | IO Module | IOMZB-110 | Multi Controller | Zigbee | frient IO Module | ||
| frient | Motion Sensor | MOSZB-141 | Motion Sensor | Zigbee | frient Motion Sensor | Show | |
| frient | Motion Sensor Pro | MOSZB-140 | Motion Sensor | Zigbee | frient Motion Sensor Pro | Show | |
| frient | Panic Button | PBTZB-110 | Button Controller | Zigbee | frient Panic Button | ||
| frient | Smart Button | SBTZB-110 | Button Controller | Zigbee | frient Smart Button | ||
| frient | smart cable 2 | SMRZB-153 | Outlet / Plug | Zigbee | Generic Zigbee Outlet | ||
| frient | Smart DIN Relay 2 | SMRZB-342 | Relay | Zigbee | Generic Zigbee Outlet | ||
| frient | Smart Humidity Sensor | HMSZB-110 | Humidity Sensor | Zigbee | frient Humidity Sensor | Show | |
| frient | Smart Mini Plug | SPLZB-131 | Outlet / Plug | Zigbee | Generic Zigbee Outlet | Show | |
| frient | Smart Plug Mini | SPLZB-134 | Outlet / Plug | Zigbee | Generic Zigbee Outlet | Show | |
| frient | Smart Plug Mini 2 | SPLZB-141 | Outlet / Plug | Zigbee | Generic Zigbee Outlet | ||
| frient | Smart Siren | SIRZB-110 | Siren | Zigbee | frient Smart Siren | Show | |
| frient | Smoke Alarm | SMSZB-120 | Smoke/CO Detector | Zigbee | frient Smoke/Heat Alarm | Show | |
| frient | Water Leak Detector | FLSZB-110 | Water Sensor | Zigbee | frient Water Leak Detector | ||
| GE/Jasco | 2-Button Hub/Panel Remote | 53829 | Button Controller | Z-Wave | Generic Z-Wave Plus Button Controller | ||
| GE/Jasco | 4-Button Hub/Panel Remote | 53831 | Button Controller | Z-Wave | Generic Z-Wave Plus Button Controller | ||
| GE/Jasco | 40 Amp Smart Switch | 14285 | Switch | Z-Wave | GE 40 Amp Smart Switch | Amazon | |
| GE/Jasco | Enbrighten Paddle Switch | 59337 | Switch | Z-Wave | Generic Z-Wave Plush Scene Switch | ||
| GE/Jasco | Enbrighten Smart Dimmer | 46203 | Dimmer | Z-Wave | GE Z-Wave Smart Dimmer | Show | Amazon |
| GE/Jasco | Enbrighten Smart Dimmer Toggle | 59341 | Dimmer | Z-Wave | Generic Z-Wave Plus Scene Dimmer | ||
| GE/Jasco | Enbrighten Smart Receptacle | 58449 | Outlet / Plug | Z-Wave | Generic Z-Wave Plus Outlet | ||
| GE/Jasco | Enbrighten Smart Switch | 46201 | Switch | Z-Wave | GE Z-Wave Smart Switch | Show | Amazon |
| GE/Jasco | Enbrighten Smart Switch | 58443 | Switch | Z-Wave | Generic Z-Wave Plus Scene Switch | ||
| GE/Jasco | Enbrighten Smart Switch Toggle | 58436 | Switch | Z-Wave | Generic Z-Wave Plush Scene Switch | ||
| GE/Jasco | Enbrighten Smart Switch Toggle | 59338 | Switch | Z-Wave | Generic Z-Wave Plus Scene Switch | ||
| GE/Jasco | Flood/Freeze Sensor | 52247 | Water Sensor | Z-Wave | Jasco Flood Freeze Sensor | ||
| GE/Jasco | GE Smart Door Sensor | 32563ZW6301 | Contact Sensor | Z-Wave | Generic Z-Wave Contact Sensor | ||
| GE/Jasco | GE/Jasco Plug-In Smart Dimmer | 14280-2 | Dimmer | Z-Wave | Jasco Z-Wave Dual Outlet | ||
| GE/Jasco | In-Wall Smart Dimmer | 43090 | Dimmer | Zigbee | GE Zigbee Dimmer | Show | |
| GE/Jasco | In-Wall Smart Dimmer | 43082 | Dimmer | Zigbee | GE Zigbee Dimmer | Show | |
| GE/Jasco | In-Wall Smart Dimmer | 43080 | Dimmer | Zigbee | GE Zigbee Dimmer | Show | |
| GE/Jasco | In-Wall Smart Dimmer | 43113 | Dimmer | Zigbee | GE Zigbee Dimmer | Show | |
| GE/Jasco | In-Wall Smart Dimmer | 43090 | Dimmer | Zigbee | GE Zigbee Dimmer | Show | |
| GE/Jasco | In-Wall Smart Dimmer | 45857 | Dimmer | Zigbee | GE Zigbee Dimmer | Show | |
| GE/Jasco | In-Wall Smart Outlet | 43102 | Outlet / Plug | Zigbee | Generic Zigbee Outlet | Show | |
| GE/Jasco | In-Wall Smart Paddle Switch | 43109 | Switch | Zigbee | Generic Zigbee Switch | Show | |
| GE/Jasco | In-Wall Smart Switch | 43076 | Switch | Zigbee | Generic Zigbee Switch | Show | |
| GE/Jasco | In-Wall Smart Switch | 42078 | Switch | Zigbee | GE Zigbee Switch | Show | |
| GE/Jasco | In-Wall Smart Switch | 43076 | Switch | Zigbee | GE Zigbee Switch | Show | Amazon |
| GE/Jasco | In-Wall Smart Switch | 45856 | Switch | Zigbee | GE Zigbee Switch | Show | |
| GE/Jasco | In-Wall Smart Toggle Switch | 43084 | Switch | Zigbee | Generic Zigbee Switch | Show | |
| GE/Jasco | Jasco Flood/Freeze Multi-Sensor | 54325 | Multisensor | Z-Wave | Jasco Flood/Freeze Sensor | ||
| GE/Jasco | Outdoor Smart Switch | 14298 | Switch | Z-Wave | Generic Z-Wave Plus Switch | Amazon | |
| GE/Jasco | Plug-In Dimmer Module Dual Controlled Plug | 43127 | Dimmer | Zigbee | GE Zigbee Dimmer | Show | |
| GE/Jasco | Plug-In Dimmer Module Dual Controlled Plug | 43096 | Dimmer | Zigbee | GE Zigbee Dimmer | Show | |
| GE/Jasco | Plug-In Dual Outlet Smart DImmer | 28175 | Dimmer | Z-Wave | Jasco Z-Wave Dual Outlet | Amazon | |
| GE/Jasco | Plug-In Dual Outlet Smart Switch | 28177 | Switch | Z-Wave | Jasco Z-Wave Dual Outlet | ||
| GE/Jasco | Plug-In Outdoor Smart Outlet | 43100 | Outlet / Plug | Zigbee | Generic Zigbee Outlet | Show | |
| GE/Jasco | Plug-In Smart Switch | 45853 | Switch | Zigbee | GE Zigbee Switch | Show | |
| GE/Jasco | Plug-In Smart Switch With Dual Controlled Outlets | 43095 | Outlet / Plug | Zigbee | Generic Zigbee Outlet | Show | |
| GE/Jasco | Plug-In Smart Switch With Dual Controlled Outlets | 43094 | Outlet / Plug | Zigbee | Generic Zigbee Outlet | Show | |
| GE/Jasco | Plug-In Switch Module Dual Controlled Plug | 43125 | Outlet / Plug | Zigbee | Generic Zigbee Outlet | Show | |
| GE/Jasco | Portable Smart Motion Sensor | 52251 | Motion Sensor | Z-Wave | Jasco Smart Motion Sensor | ||
| GE/Jasco | Slim Door/Window Sensor | 52249 | Contact Sensor | Z-Wave | Generic Z-Wave Plus Contact Sensor | ||
| GE/Jasco | Smart Dimmer | 14296 | Dimmer | Z-Wave | GE Enbrighten Z-Wave Smart Dimmer | Show | |
| GE/Jasco | Smart Dimmer | 46204 | Dimmer | Z-Wave | GE Enbrighten Z-Wave Smart Dimmer | Amazon | |
| GE/Jasco | Smart Dimmer | 52252 | Dimmer | Z-Wave | GE Enbrighten Z-Wave Smart Dimmer | ||
| GE/Jasco | Smart Dimmer | 14294 | Dimmer | Z-Wave | Generic Z-Wave Smart Dimmer | Show | Amazon |
| GE/Jasco | Smart Fan Control | 55258 | Fan Controller | Z-Wave | GE Smart Fan Control | Amazon | |
| GE/Jasco | Smart LED Bulb | 52190 | Bulb | Z-Wave | Generic Z-Wave Plus Dimmer | ||
| GE/Jasco | Smart Motion Dimmer | 26993 | Dimmer | Z-Wave | Jasco Z-Wave Motion Dimmer | Amazon | |
| GE/Jasco | Smart Motion Switch | 26931 | Switch | Z-Wave | Jasco Z-Wave Motion Switch | Show | |
| GE/Jasco | Smart Outlet | 14267 | Outlet / Plug | Z-Wave | Generic Z-Wave Plus Outlet | ||
| GE/Jasco | Smart Outlet | 55249 | Outlet / Plug | Z-Wave | Jasco Z-Wave Dual Outlet | Amazon | |
| GE/Jasco | Smart Outlet | 55256 | Outlet / Plug | Z-Wave | Generic Z-Wave Plus Outlet | Amazon | |
| GE/Jasco | Smart Switch | 14293 | Switch | Z-Wave | Generic Z-Wave Plus Scene Switch | Show | |
| GE/Jasco | Smart Switch | 43072, 43074, 46201, 46202 | Switch | Z-Wave | Generic Z-Wave Plus Scene Switch | Show | Amazon |
| GE/Jasco | Smart Switch | 14291 | Switch | Z-Wave | Generic Z-Wave Smart Switch | Show | Amazon |
| GE/Jasco | Tamper Resistant Smart Outlet | 43132 | Outlet / Plug | Zigbee | Generic Zigbee Outlet | Show | |
| GLEDOPTO | Mini RGB+CCT Controller | GL-MC-001 | Bulb | Zigbee | Generic ZigBee RGBW Light | Show | |
| Global Cache | Global Connect IR Module | GCIR3 | Contact Sensor | LAN | Global Connect IR Module | Show | |
| Global Cache | Global Connect Relay Module | GCRL3A | Relay | LAN | Global Connect Relay Module | Show | |
| GoControl | Dimmable LED Indoor Flood Light | LBR30Z-1 | Bulb | Z-Wave | Generic Z-Wave Smart Dimmer | Amazon | |
| GoControl | Garage Door Controller | GD00Z-2, GD00Z-4, GD00Z-5, GD00Z-6, GD00Z-7, ND00Z | Garage Door Controller | Z-Wave | Generic Z-Wave Garage Door Opener | Show | Amazon |
| GoControl | Glass Break Detector | Glass Break Detector | Z-Wave | Generic Glass Break Detector | |||
| GoControl | Smart LED Light Bulb | LB60Z-1 | Bulb | Z-Wave | Generic Z-Wave Dimmer | ||
| GoControl | Smart Wireless Light Switch | WA00Z-1 | Button Controller | Z-Wave | Generic Z-Wave Button Controller | Amazon | |
| GoControl | Z-Wave Thermostat | GC-TBZ48 | Thermostat | Z-Wave | GoControl Z-Wave Thermostat | Show | Amazon |
| Chromecast | Media Renderer | Hidden | Chromecast Integration (beta) (app) | ||||
| Google Home Assistant | Voice Assistant | Hidden | Google Home installation helper (app) | Show | |||
| Google Nest Matter Thermostat | Thermostat | Matter | Google Nest Matter Thermostat | ||||
| Govee | RGBIC LED Strip Lights M1 | Bulb | Matter | Generic Matter RGBW Light | |||
| Graber | Z-Wave+ Roller Blinds (Motorized Shades) | Shade Controller | Z-Wave | Generic Z-Wave Shade | Show | ||
| Halo Labs | Halo+ Smoke Alarm | LS001A | Smoke/CO Detector | Zigbee | Halo Smoke Alarm | Show | |
| Hampton Bay | Ceiling Fan Controller | MR101Z | Fan Controller | Zigbee | null (app) | Show | |
| Hank | Four-Key Scene Controller | HKZW-SCN04 | Button Controller | Z-Wave | Aeotec NanoMote | Show | |
| Hank | One-Key Scene Controller | HKZW-SCN01 | Button Controller | Z-Wave | Aeotec NanoMote | Show | |
| Hank | RGBW LED Bulb | HKZW-RGB01 | Bulb | Z-Wave | Hank RGBW LED Bulb | Show | |
| Haozee | Door Sensor 700 Series | NAS-DS01Z | Contact Sensor | Z-Wave | Neo Door Sensor 700 | ||
| Haozee | Motion Sensor 700 Series | Z-PIR | Motion Sensor | Z-Wave | Neo Motion Sensor 700 | ||
| Heatit | Heatit Z-Water | Z-Water | Valve | Z-Wave | Heatit Z-Water | Show | |
| Heatit | Heatit ZM Single Relay | ZM Single Relay 16A | Relay | Z-Wave | Heatit ZM Single Relay | Show | |
| Heatit | Heatit ZM Thermostat | ZM Thermostat | Thermostat | Z-Wave | Heatit ZM Thermostat | Show | |
| Heatit | Single Relay | Relay | Z-Wave | Heatit ZM Single Relay | |||
| Heatit | Thermostat | Thermostat | Z-Wave | Heatit ZM Thermostat | |||
| Heatit | Z-Dim | 14 444 44 | Dimmer | Z-Wave | Heatit Z-Dim | Show | |
| Heatit | Z-Repeater | 45 126 86 | Repeater | Z-Wave | Heatit Z-Repeater | Show | |
| Heatit | Z-Smoke 230V | 45 126 89 | Smoke/CO Detector | Z-Wave | Heatit Z-Smoke | Show | |
| Heatit | Z-Smoke Battery | 45 126 88 | Smoke/CO Detector | Z-Wave | Heatit Z-Smoke | ||
| Heatit | Z-Temp2 | 45 126 66 | Thermostat | Z-Wave | Heatit Z-Temp2 | Show | |
| Heatit | Z-TRM3 | 54 305 98 | Thermostat | Z-Wave | Heatit Z-TRM3 | Show | |
| Heatit | Z-Water | Water Sensor | Z-Wave | Heatit Z-Water | |||
| Heiman | Z-Wave Smoke Detector | HS1SA-Z | Smoke/CO Detector | Z-Wave | Generic Z-Wave Smoke Detector | ||
| Heiman | Zigbee Gas Detector | HS1CG | Gas Detector | Zigbee | Heiman Zigbee Gas Detector | Show | |
| Heltun | Fan Coil Thermostat | HE-FT01 | Thermostat | Z-Wave | Heltun Fan Coil Thermostat | ||
| Heltun | Heating Thermostat | HE-HT01 | Thermostat | Z-Wave | Heltun Heating Thermostat | ||
| Heltun | Relay Switch Quinto | HE-RS01 | Relay | Z-Wave | Heltun Relay Switch Quinto | ||
| Heltun | Touch Panel Switch Duo | HE-TPS02 | Switch | Z-Wave | Heltun Touch Panel Switch | ||
| Heltun | Touch Panel Switch Quarto | HE-TPS04 | Switch | Z-Wave | Heltun Touch Panel Switch | ||
| Heltun | Touch Panel Switch Quinto | HE-TPS04 | Switch | Z-Wave | Heltun Touch Panel Switch | ||
| Heltun | Touch Panel Switch Sexto | HE-TPS06 | Switch | Z-Wave | Heltun Touch Panel Switch | ||
| Heltun | Touch Panel Switch Solo | HE-TPS01 | Switch | Z-Wave | Heltun Touch Panel Switch | ||
| Heltun | Touch Panel Switch Trio | HE-TPS03 | Switch | Z-Wave | Heltun Touch Panel Switch | ||
| Hikvision | Hikvision Camera | Camera | LAN | Hikvision Camera | |||
| HomePro | Outlet | ZRP110 | Outlet / Plug | Z-Wave | Generic Z-Wave Outlet | Show | |
| Homeseer | HomeSeer Fan Controller | FC200+ | Fan Controller | Z-Wave | HomeSeer Fan Controller FC200+ | Show | Amazon |
| Homeseer | HomeSeer Floodlight Sensor | HS-FLS100+ | Light Sensor | Z-Wave | HomeSeer Floodlight Sensor | ||
| Homeseer | HomeSeer Floodlight Sensor G2 | HS-FLS100-G2 | Light Sensor | Z-Wave | HomeSeer Floodlight Sensor G2 | Amazon | |
| Homeseer | HomeSeer Indicator Light Sensor | HS-FS100-L+ | Light Sensor | Z-Wave | HomeSeer Flex Sensor | Show | Amazon |
| Homeseer | HomeSeer Multi-Sensor | HSM200 | Motion Sensor | Z-Wave | HomeSeer Multi-Sensor HSM200 | Amazon | |
| Homeseer | HomeSeer Perimeter Water Sensor | HS-FS100-W+ | Water Sensor | Z-Wave | HomeSeer Flex Sensor | Show | |
| Homeseer | Leak Sensor | HS-LS100+ | Water Sensor | Z-Wave | HomeSeer Leak Sensor | Show | |
| Homeseer | Wall Dimmer | HS-WD200+ | Dimmer | Z-Wave | HomeSeer WD-200 Dimmer | Show | Amazon |
| Homeseer | Wall Switch | HS-WS200+ | Switch | Z-Wave | Generic Z-Wave CentralScene Switch | Show | |
| Homeseer | ZWave Plus Door/Window Sensor | HS-DS100+ | Contact Sensor | Z-Wave | Generic Z-Wave Contact Sensor | Show | |
| Honeywell | T6 Pro Z-Wave Thermostat | TH6320ZW2003 | Thermostat | Z-Wave | Honeywell T6 Pro Z-Wave Thermostat | Show | Amazon |
| Hubitat (virtual devices) | Component Presence Sensor | Presence Sensor | Virtual | Generic Component Presence Sensor | |||
| Hubitat (virtual devices) | Component Sound Sensor | Sound Sensor | Virtual | Generic Component Sound Sensor | |||
| Hubitat (virtual devices) | Generic Component Audio Zone | Audio Video Receiver | Virtual | Generic Component Audio Zone | |||
| Hubitat (virtual devices) | Virtual Acceleration Sensor | Acceleration Sensor | Virtual | Virtual Acceleration Sensor | |||
| Hubitat (virtual devices) | Virtual Button | Button Controller | Virtual | Virtual Button | |||
| Hubitat (virtual devices) | Virtual CO Detector | Smoke/CO Detector | Virtual | Virtual CO Detector | |||
| Hubitat (virtual devices) | Virtual Color Temperature Light | Bulb | Virtual | Virtual Color Temperature Light | |||
| Hubitat (virtual devices) | Virtual Contact Sensor | Contact Sensor | Virtual | Virtual Contact Sensor | |||
| Hubitat (virtual devices) | Virtual Dimmer | Dimmer | Virtual | Virtual Dimmer | |||
| Hubitat (virtual devices) | Virtual Fan Controller | Fan Controller | Virtual | Virtual Fan Controller | |||
| Hubitat (virtual devices) | Virtual Garage Door Controller | Garage Door Controller | Virtual | Virtual Garage Door Controller | |||
| Hubitat (virtual devices) | Virtual Humidity Sensor | Humidity Sensor | Virtual | Virtual Humidity Sensor | |||
| Hubitat (virtual devices) | Virtual Illuminance Sensor | Light Sensor | Virtual | Virtual Illuminance Sensor | |||
| Hubitat (virtual devices) | Virtual Lock | Lock | Virtual | Virtual Lock | |||
| Hubitat (virtual devices) | Virtual Lock (no codes) | Lock | Virtual | Virtual Lock (no codes) | |||
| Hubitat (virtual devices) | Virtual Moisture Sensor | Water Sensor | Virtual | Virtual Moisture Sensor | |||
| Hubitat (virtual devices) | Virtual Motion Sensor | Motion Sensor | Virtual | Virtual Motion Sensor | |||
| Hubitat (virtual devices) | Virtual Multi Sensor | Multisensor | Virtual | Virtual Multi Sensor | |||
| Hubitat (virtual devices) | Virtual Omni Sensor | Multisensor | Virtual | Virtual Omni Sensor | |||
| Hubitat (virtual devices) | Virtual Presence | Presence Sensor | Virtual | Virtual Presence | |||
| Hubitat (virtual devices) | Virtual RGB Light | Bulb | Virtual | Virtual RGB Light | |||
| Hubitat (virtual devices) | Virtual RGBW Light | Bulb | Virtual | Virtual RGBW Light | |||
| Hubitat (virtual devices) | Virtual Shade | Shade Controller | Virtual | Virtual Shade | |||
| Hubitat (virtual devices) | Virtual Smoke Detector | Smoke/CO Detector | Virtual | Virtual Smoke Detector | |||
| Hubitat (virtual devices) | Virtual Switch | Switch | Virtual | Virtual Switch | |||
| Hubitat (virtual devices) | Virtual Temperature Sensor | Temperature Sensor | Virtual | Virtual Temperature Sensor | |||
| Hubitat (virtual devices) | Virtual test device | Switch | Virtual | Virtual test device | |||
| Hubitat (virtual devices) | Virtual Thermostat | Thermostat | Virtual | Virtual Thermostat | |||
| iBlinds | HAB Home Intel Z-Wave iBlinds V3 | IB3.0 | Shade Controller | Z-Wave | HAB Home Intel Blinds V3 | ||
| IKEA | Outlet strip | Outlet / Plug | Zigbee | Ikea TRADFRI control outlet | |||
| IKEA | SYMFONISK Sound Remote | 20370482 | Button Controller | Zigbee | Ikea Zigbee Sound Controller | Show | |
| IKEA | TRADFRI Remote Control | Button Controller | Zigbee | TRADFRI Remote Control | |||
| IKEA | TRÅDFRI Bulb E26 | Bulb | Zigbee | Generic Zigbee CT Bulb | Show | ||
| IKEA | TRÅDFRI Outlet | Outlet / Plug | Zigbee | Ikea TRADFRI Control Outlet | Show | ||
| IKEA | TRÅDFRI Signal Repeater | Repeater | Zigbee | Ikea TRADFRI Signal Repeater | Show | ||
| Innr | Color Bulb | AE 280 C | Bulb | Zigbee | Advanced Zigbee RGBW Bulb | ||
| Innr | Smart Plug | SP 234 | Outlet / Plug | Zigbee | Generic Zigbee Outlet | Show | |
| Innr | Smart Spot Colour GU10 | RS 230 C | Bulb | Zigbee | Generic ZigBee RGBW Light | Show | |
| Innr | Zigbee outlet - UK version | SP222 | Outlet / Plug | Zigbee | Generic Zigbee Outlet | Show | |
| Inovelli | 2-Channel Plug | NZW37 | Outlet / Plug | Z-Wave | Inovelli 2-Channel Plug | ||
| Inovelli | Inovelli 4-in-1 Sensor | LZW60 | Motion Sensor | Z-Wave | Inovelli 4-in-1 Sensor | ||
| Inovelli | Inovelli Fan/Light Switch | LZW36 | Fan Controller | Z-Wave | Inovelli Fan/Light Switch | ||
| Inovelli | On/Off Switch S2 | LZW30 | Switch | Z-Wave | Inovelli Z-Wave Smart Switch S2 | Show | |
| Inovelli | Outlet | Outlet / Plug | Z-Wave | Generic Z-Wave Outlet | Show | ||
| Inovelli | RGBW Multi-Color Bulb | LZW42 | Bulb | Z-Wave | Inovelli Bulb Multi-Color | ||
| Inovelli | Scene Dimmer | Red Scene Dimmer | Dimmer | Z-Wave | Inovelli Z-Wave Red Scene Dimmer | ||
| Inovelli | Smart Dimmer | NZW31 | Dimmer | Z-Wave | Inovelli Z-Wave Dimmer | Show | |
| Inovelli | Smart Scene Dimmer | NZW31 | Dimmer | Z-Wave | Inovelli Z-Wave Smart Scene Dimmer | Show | |
| Inovelli | Smart Scene Switch | NZW30 | Switch | Z-Wave | Inovelli Z-Wave Smart Scene Switch | Show | |
| Inovelli | Smart Scene Switch S2 | LZW30-SN | Switch | Z-Wave | Inovelli Z-Wave Smart Scene Switch S2 | Show | |
| Inovelli | Smart Switch | NZW30 | Switch | Z-Wave | Inovelli Z-Wave Smart Switch | Show | |
| Inovelli | Switch | Switch | Z-Wave | Generic Z-Wave Smart Switch | Show | ||
| Inovelli | Switch Module | Switch | Z-Wave | Generic Z-Wave Smart Switch | Show | ||
| Inovelli | Tuneable White Bulb | LZW41 | Bulb | Z-Wave | Inovelli Bulb Multi-White | ||
| Iris | Garage Door Opener | GD-00Z-1 | Garage Door Controller | Z-Wave | Generic Z-Wave Garage Door Opener | Show | |
| Iris | Smart Plug Z-Wave Repeater | Repeater | Z-Wave | Generic Z-Wave Repeater | |||
| Iris | Smart Water Sensor | 3315-L | Water Sensor | Zigbee | Generic Zigbee Moisture Sensor | Show | |
| Iris | V2 Button | 3460-L | Button Controller | Zigbee | Iris Button Controller | Show | |
| Iris | V2 Door/Window Sensor | 3320-L | Contact Sensor | Zigbee | Generic Zigbee Contact Sensor | Show | |
| Iris | V2 Keypad | 3405-L | Keypad | Zigbee | Iris V2 Keypad | Show | |
| Iris | V2 Motion Sensor | 3326-L | Motion Sensor | Zigbee | Generic Zigbee Motion Sensor | Show | |
| Iris | V2 Outlet | 3210-L | Outlet / Plug | Zigbee | Generic Zigbee Outlet | Show | |
| Iris | V2 Smart Fob | 3450-L | Button Controller | Zigbee | Iris 4 Button Fob | Show | |
| Iris | V3 Contact Sensor | 1116-S | Contact Sensor | Zigbee | Generic Zigbee Contact Sensor | Show | |
| Iris | V3 Keypad | iL02_1 | Keypad | Zigbee | Iris V3 Keypad | Show | |
| Iris | V3 Motion Sensor | iL07_1 | Motion Sensor | Zigbee | Generic Zigbee Motion/Humidity Sensor | Show | |
| Iris V1 (AlertMe.com) | Smart Plug | SPG100 | Outlet / Plug | Zigbee | Iris V1 Outlet | Show | |
| Iris V1 (AlertMe.com) | V1 Button | BTN900 | Button Controller | Zigbee | Iris V1 Button | Show | |
| Iris V1 (AlertMe.com) | V1 Care Pendant | PDT900 | Button Controller | Zigbee | Iris V1 Care Pendant | Show | |
| Iris V1 (AlertMe.com) | V1 Door/Window Sensor | DWS800 | Contact Sensor | Zigbee | Iris V1 Contact Sensor | Show | |
| Iris V1 (AlertMe.com) | V1 Keyfob | KEY903 | Presence Sensor | Zigbee | Iris V1 Key Fob | Show | |
| Iris V1 (AlertMe.com) | V1 Motion Sensor | MOT800 | Motion Sensor | Zigbee | Iris V1 Motion Sensor | Show | |
| Iris V1 (AlertMe.com) | V1 Smart Plug | SPG800 | Outlet / Plug | Zigbee | Iris V1 Outlet | Show | |
| Kaadas | Smart Lock | KA201 | Lock | Z-Wave | Generic Z-Wave Lock | ||
| Kaadas | Smart Lock | KA211 | Lock | Z-Wave | Generic Z-Wave Lock | ||
| Kaadas | Smart Lock | KA200 | Lock | Z-Wave | Generic Z-Wave Lock | ||
| KAIPULE | Ceiling-Mounted Motion Sensor | Motion Sensor | Z-Wave | BeSense Motion Sensor | |||
| Kasa | Matter Smart Dimmer Switch | Dimmer | Matter | Generic Matter Dimmer | |||
| Kasa | Matter Smart Plug | Outlet / Plug | Matter | Generic Matter Outlet | |||
| Kasa | Matter Smart Switch | Switch | Matter | Generic Matter Switch | |||
| KEEN Home | Smart Vent | Vent | Zigbee | Keen Home Smart Vent | Show | ||
| keyWe | Lock | Lock | Z-Wave | keyWe Z-Wave Lock | Amazon | ||
| Kwikset | 10-Button Deadbolt | Lock | Zigbee | Generic Zigbee Lock | Show | ||
| Kwikset | 10-Button Touch Deadbolt | Lock | Zigbee | Generic Zigbee Lock | Show | ||
| Kwikset | 5-Button Deadbolt | Lock | Zigbee | Generic Zigbee Lock | Show | ||
| Kwikset | 5-Button Lever | Lock | Zigbee | Generic Zigbee Lock | Show | ||
| Kwikset | 910/912/914 Lock | 910, 912, 914 | Lock | Z-Wave | Generic Z-Wave Lock | Show | Amazon |
| Kwikset | Kwikset Connect | 620 | Lock | Z-Wave | Generic Z-Wave Lock | ||
| Kwikset | Smartcode Lock | Lock | Zigbee | Generic Zigbee Lock | Show | Amazon | |
| Kwikset | Touchscreen Deadbolt | 916 | Lock | Zigbee | Generic Zigbee Lock | Show | |
| Leak Intelligence | Leak Gopher Valve | Valve | Z-Wave | Generic Z-Wave Valve | |||
| Leaksmart | Water Sensor | 8850600 | Water Sensor | Zigbee | Leaksmart Zigbee Moisture Sensor | Show | |
| Leaksmart | Water Valve | 8880000 | Valve | Zigbee | Sinope water valve | Show | |
| Legrand | Mobile Outlet | WNRR15WH | Outlet / Plug | Zigbee | Generic Zigbee Outlet | ||
| Legrand | Mobile Outlet | WNRR20WH | Outlet / Plug | Zigbee | Generic Zigbee Outlet | ||
| Leviton | Dimmer | VRMX1 | Dimmer | Z-Wave | Generic Z-Wave Dimmer | ||
| Leviton | Dimmer | VRI06-1LZ, VRI10-1LZ | Dimmer | Z-Wave | Generic Z-Wave Dimmer | ||
| Leviton | Fan Controller | Fan Controller | Z-Wave | Leviton Fan Controller | Amazon | ||
| Leviton | In-Wall Dimmer | DG6HD | Dimmer | Zigbee | Leviton Zigbee Dimmer | Show | |
| Leviton | In-Wall Switch | DG15S | Switch | Zigbee | Generic Zigbee Switch | Show | |
| Leviton | Matter Switch | Switch | Matter | Generic Matter Switch | |||
| Leviton | Plug-in Appliance Module | DZPA1 | Outlet / Plug | Z-Wave | Generic Z-Wave Outlet | Show | |
| Leviton | Plug-in Dimmer | DG3HL | Dimmer | Zigbee | Leviton Zigbee Dimmer | Show | |
| Leviton | Plug-in Outlet | DG15A | Outlet / Plug | Zigbee | Generic Zigbee Switch | Show | |
| Leviton | Scene controller | VRCS4 | Button Controller | Z-Wave | Leviton VRCS4 Z-Wave Controller | Show | |
| Leviton | Smart Dimmer | DZ6HD | Dimmer | Z-Wave | Leviton DZ6HD Z-Wave Dimmer | Show | Amazon |
| Leviton | Smart Dimmer | DZMX1 | Dimmer | Z-Wave | Generic Z-Wave Smart Dimmer | Amazon | |
| Leviton | Switch | VRCS1 | Switch | Z-Wave | Leviton VRCS1 Z-Wave Controller | ||
| Leviton | Switch | DL15S | Switch | Zigbee | Generic Zigbee Switch | Show | Amazon |
| Leviton | Switch | DZ15S | Switch | Z-Wave | Generic Z-Wave Smart Switch | Amazon | |
| Leviton | Switch | DZS15-1LZ | Switch | Z-Wave | Generic Z-Wave Switch | ||
| Leviton | Switch | VRS15-1LZ | Switch | Z-Wave | Generic Z-Wave Switch | ||
| Leviton | Tamper-Resistant Outlet | ZW15R | Outlet / Plug | Z-Wave | Generic Z-Wave Outlet | ||
| Life360 | Life360 App | Presence Sensor | Hidden | Life360 Connector (app) | Show | ||
| LIFX | 4-Gang Switch | Switch | LAN | LIFX Integration (app) | Show | ||
| LIFX | A19 Bulb | Bulb | LAN | LIFX Integration (app) | Show | Amazon | |
| LIFX | BR30 Bulb | Bulb | LAN | LIFX Integration (app) | Show | Amazon | |
| LIFX | Candle White to Warm | Bulb | LAN | LIFX Integration (app) | Show | Amazon | |
| LIFX | Color bulb | Bulb | LAN | LIFX Integration (app) | Show | Amazon | |
| LIFX | CT Bulb | Bulb | LAN | LIFX Integration (app) | Show | Amazon | |
| LIFX | Mini Color Bulb | Bulb | LAN | LIFX Integration (app) | Show | Amazon | |
| LIFX | Mini Day Dusk Bulb | Bulb | LAN | LIFX Integration (app) | Show | Amazon | |
| LIFX | Mini White Bulb | Bulb | LAN | LIFX Integration (app) | Show | Amazon | |
| LIFX | Strip | Bulb | LAN | LIFX Integration (app) | Show | Amazon | |
| LIFX | Switch | Switch | LAN | LIFX Integration (app) | Show | Amazon | |
| LIFX | White Bulb | Bulb | LAN | LIFX Integration (app) | Show | Amazon | |
| Linear | Contact Sensor | WADWAZ-1 | Contact Sensor | Z-Wave | Generic Z-Wave Contact Sensor | Show | |
| Linear | Motion Sensor | WAPIRZ-1 | Motion Sensor | Z-Wave | Generic Z-Wave Motion/Temperature Sensor | Show | |
| Linear | Siren | WA105DBZ-1 | Siren | Z-Wave | Linear/Vision Siren | Show | |
| Linkind | Dimmable White Bulb | ZL1000100-CCT/DIM-US | Bulb | Zigbee | Advanced Zigbee Bulb | Show | |
| Linkind | Door/Window Sensor | ZS1100500 | Contact Sensor | Zigbee | Generic Zigbee Contact Sensor | Show | |
| Linkind | Matter Smart Bulb | Bulb | Matter | Generic Matter RGBW Light | |||
| Linkind | Matter Smart Plug | Outlet / Plug | Matter | Generic Matter Outlet | |||
| Linkind | Motion Sensor | ZS1100400 | Motion Sensor | Zigbee | Linkind Zigbee Motion Sensor | Show | |
| Linkind | Smart Plug | WS1900000-IN-US | Outlet / Plug | Zigbee | Generic Zigbee Outlet | Show | |
| Linkind | Tunable White Bulb | ZL1000100-CCT-EU | Bulb | Zigbee | Advanced Zigbee CT Bulb | Show | |
| Lutron | Aurora Controller | Z3-1BRL | Button Controller | Zigbee | Lutron Aurora Controller | Show | Amazon |
| Lutron | Caséta Fan Control | PD-FSQN | Fan Controller | Integration | (app) | Show | Amazon |
| Lutron | Caséta In-Wall Smart Dimmer Switch | PD-6WCL | Dimmer | Integration | (app) | Show | Amazon |
| Lutron | Caséta In-Wall Smart Dimmer Switch for ELV | PD-5NE | Dimmer | Integration | (app) | Show | Amazon |
| Lutron | Caséta Lamp Dimming Smart Plug | PD-3PCL | Dimmer | Integration | (app) | Show | Amazon |
| Lutron | Caséta Outdoor Smart Plug | PD-15OUT | Outlet / Plug | Integration | (app) | Show | Amazon |
| Lutron | Caséta Serena Shades | All | Shade Controller | Integration | (app) | Show | |
| Lutron | Caséta Smart Switch For Light or Fan Control | PD-6ANS | Switch | Integration | (app) | Show | Amazon |
| Lutron | Caséta SmartBridge Pro | L-BDGPRO2 | Bridge | LAN | Lutron Integrator (app) | Show | Amazon |
| Lutron | Lutron Component Switch | Switch | Hidden | Lutron Component Switch | |||
| Lutron | Lutron fan control (no level) | Fan Controller | Integration | (app) | Show | ||
| Lutron | Lutron SeeTouch Keypad | Button Controller | Integration | (app) | Show | ||
| Lutron | Lutron Shade (no level or switch commands) | Shade Controller | Integration | (app) | Show | ||
| Lutron | Pico Remote | All | Button Controller | Integration | (app) | Show | Amazon |
| Lutron | RadioRA2 Dimmer | All | Dimmer | Integration | (app) | Show | Amazon |
| Lutron | RadioRA2 HVAC Controller | LR-HVAC-1 | HVAC Controller | Integration | (app) | Show | |
| Lutron | RadioRA2 Keypad | All | Button Controller | Integration | (app) | Show | |
| Lutron | RadioRA2 Main Repeater | RR-MAIN-REP | Bridge | LAN | Lutron Integrator (app) | Show | |
| Lutron | RadioRA2 Motion/Occupancy Sensor | All | Motion Sensor | Integration | (app) | Show | |
| Lutron | RadioRA2 Select Main Repeater | RR-SEL-REP2 | Bridge | LAN | Lutron Integrator (app) | Show | |
| Lutron | RadioRA2 Switch | All | Switch | Integration | (app) | Show | |
| Lutron | RadioRA2 Thermostat | All | Thermostat | Integration | (app) | Show | |
| Lutron | RadioRA2 VCRX Visor Controller Receiver | RR-VCRX | Garage Door Controller | Integration | (app) | Show | |
| Lutron | Shade Remote | CS-YJ-4GC-WH | Button Controller | LAN | Lutron Shade Remote | ||
| Lutron | Sivoia QS Triathlon Shades | All | Shade Controller | Integration | (app) | Show | |
| Lux | Zigbee Thermostat | KONOz | Thermostat | Zigbee | LUX Zigbee Thermostat | Show | Amazon |
| Marantz | Audio Video Receiver | Any with Ethernet port | Audio Video Receiver | LAN | Denon AVR | Show | Amazon |
| MCOHome | Dimmer Switch | Dimmer | Z-Wave | Generic Z-Wave Smart Dimmer | Show | ||
| Melross | Meross Smart Plug Mini | Outlet / Plug | Matter | Generic Matter Outlet | |||
| MHCOZY | Relay | 1, 2 and 4 channel relay | Relay | Zigbee | Generic Zigbee Multi-Endpoint Switch | Show | |
| Minoston | 2-Channel Plug | MP20Z | Outlet / Plug | Z-Wave | Inovelli 2-Channel Plug | ||
| Minoston | 3-in-1 Sensor | MSE30Z | Multisensor | Z-Wave | Minoston 3-in-1 Sensor | ||
| Minoston | In-Wall Smart Switch | MS10Z | Switch | Z-Wave | EVA LOGIK In-Wall Switch | ||
| Minoston | Mini Plug-in Outlet | MP21Z | Outlet / Plug | Z-Wave | Generic Z-Wave Outlet | Amazon | |
| Minoston | Mini Power Meter Plug | MP21ZP | Outlet / Plug | Z-Wave | Minoston Mini Power Meter Plug | ||
| Minoston | Mini Smart Plug Dimmer | MP21ZD | Dimmer | Z-Wave | Ministon Mini Smart Plug Dimmer | Show | |
| Minoston | Outdoor Dimmer Plug | MP22ZD | Dimmer | Z-Wave | Generic Z-Wave Plus Dimmer | ||
| Minoston | Smart Dimmer Switch | MS11ZS | Switch | Z-Wave | Minoston MS11ZS Dimmer | ||
| Minoston | Smart Switch | MS10ZS | Switch | Z-Wave | Minoston MS10ZS Switch | ||
| Mode Lighting | eDIN+ Network Processor Module | DIN-NPU-00-01-PLUS | Network Controller | LAN | eDIN Network Controller | Show | |
| Moes | Temperature Humidity Sensor | RH3052 | Temperature Sensor | Zigbee | Generic Zigbee Temperature/Humidity | ||
| Monoprice | 6 Zone Audio Controller | 39261 | Audio Video Receiver | LAN | Monoprice 6 Zone Audio Controller | Show | |
| Monoprice | Contact Sensor | 24259 | Contact Sensor | Z-Wave | Generic Z-Wave Contact Sensor | Show | |
| Monoprice | Outlet | 15654 | Outlet / Plug | Z-Wave | Generic Z-Wave Outlet | Show | |
| Monoprice | Plugin Dimmer | 11994 | Dimmer | Z-Wave | Generic Z-Wave Dimmer | Show | |
| Monoprice | Z-Wave Plugin On/Off | 11995 | Outlet / Plug | Z-Wave | Generic Z-Wave Outlet | Show | |
| Monoprice | Z-Wave Plus Door/Window Sensor | 15270 | Contact Sensor | Z-Wave | Generic Z-Wave Contact Sensor | Show | |
| Monoprice | Z-Wave Plus PIR Motion Detector With Temperature Sensor | 15271 | Motion Sensor | Z-Wave | Generic Z-Wave Motion/Temperature Sensor | Show | |
| Monoprice | Z-Wave Plus PIR Multi Sensor | 15902 | Motion Sensor | Z-Wave | Zooz 4-in-1 Sensor | Show | |
| Monoprice | Z-Wave Plus Recessed Door/Window Sensor | 15268 | Contact Sensor | Z-Wave | Generic Z-Wave Contact Sensor | Show | |
| Monoprice | Z-Wave Plus Smart Plug and Repeater with 2 USB ports | 27481 | Outlet / Plug | Z-Wave | Zooz Power Switch | Show | |
| Mujoy | Smart Bulb | Bulb | Matter | Generic Matter RGBW Light | |||
| NanoLeaf | Aurora Light Panels | Bulb | LAN | Nanoleaf Aurora | Show | ||
| NanoLeaf | Canvas Light Panels | Bulb | LAN | Nanoleaf Aurora | Show | ||
| NanoLeaf | Essentials Matter Lightstrip | Bulb | Matter | Generic Matter RGBW Light | |||
| NanoLeaf | Essentials Matter Smart Bulb | Bulb | Matter | Generic Matter RGBW Light | |||
| NanoLeaf | Matter Smart Holiday String Light | Bulb | Matter | Generic Matter RGBW Light | |||
| NEEO | NEEO Remote | AVR Remote | LAN | NEEO Remote | Show | ||
| NEO | Door Sensor | NAS-DS07ZU | Contact Sensor | Z-Wave | Neo Door Sensor 700 | Show | |
| NEO | Matter Smart Plug | Outlet / Plug | Matter | Generic Matter Outlet | |||
| NEO | Neo Coolcam Door Sensor 700 | NAS-DS07ZU | Contact Sensor | Z-Wave | Neo Door Sensor 700 | ||
| NEO | NEO Coolcam Door/Window Sensor | NAS-DS02ZU | Contact Sensor | Z-Wave | Generic Z-Wave Contact Sensor | Show | |
| NEO | NEO Coolcam Door/Window Sensor | NAS-DS01ZE | Contact Sensor | Z-Wave | Generic Z-Wave Contact Sensor | Show | |
| NEO | Neo Coolcam Light Switch | NAS-SC02ZU-1, NAS-SC02ZU-2 | Switch | Z-Wave | Neo Coolcam Light Switch | ||
| NEO | NEO Coolcam Motion Sensor | NAS-PD01ZU-T | Motion Sensor | Z-Wave | Neo Coolcam Motion Sensor | Show | Amazon |
| NEO | Neo Coolcam Motion Sensor 700 | NAS-PD07ZU | Motion Sensor | Z-Wave | Neo Motion Sensor 700 | ||
| NEO | NEO Coolcam Power Plug | NAS-WR01ZU | Outlet / Plug | Z-Wave | Neo Coolcam Power Plug | Show | |
| NEO | NEO Coolcam Remote Control | Button Controller | Z-Wave | Neo Coolcam Remote Control | Show | ||
| NEO | Neo Coolcam Water Sensor 700 | NAS-WS02ZU | Water Sensor | Z-Wave | Neo Water Sensor 700 | ||
| NEO | Neo Coolcam Z-Wave Repeater 700 | NAS-RP02Z1U | Repeater | Z-Wave | Neo Z-Wave Repeater 700 | ||
| New One | Mini Smart Plug | N4001 | Outlet / Plug | Z-Wave | Generic Z-Wave Plus Outlet | ||
| New One | Mini Smart Plug Dimmer | N4002 | Dimmer | Z-Wave | Generic Z-Wave Plus Dimmer | ||
| Nexia | Scene Controller | NX1000 | Button Controller | Z-Wave | Nexia NX1000 | ||
| NodOn | Octan Remote | CRC-3US-1 | Button Controller | Z-Wave | Generic Z-Wave Button Controller | Show | |
| NodOn | Soft Remote | CRC-3US-6 | Button Controller | Z-Wave | Generic Z-Wave Button Controller | Show | Amazon |
| Nue | 1 Gang Light Switch | HGZB-41 | Switch | Zigbee | Nue Zigbee Switch | Show | |
| Nue | 2 Gang Light Switch | HGZB-42 | Switch | Zigbee | Nue Zigbee Switch | Show | |
| Nue | 3 Gang Light Switch | HGZB-43 | Switch | Zigbee | Nue Zigbee Switch | Show | |
| Nue | 4 Gang Light Switch | HGZB-44 | Switch | Zigbee | Nue Zigbee Switch | Show | |
| Nue | RGBW Strip Controller | ZB-18A | Bulb | Zigbee | Generic Zigbee RGBW Light | Show | |
| Nue | Zigbee 3.0 Light Controller | HGZB-07A | Bulb | Zigbee | Generic ZigBee RGBW Light | Show | |
| Nue | Zigbee 3.0 Smart Socket Plug | HGZB-20A | Outlet / Plug | Zigbee | Generic Zigbee Outlet | Show | |
| Nue | Zigbee Dimmer | HGZB-021 | Dimmer | Zigbee | Nue Zigbee Dimmer | Show | |
| Nue | Zigbee Dimmer | HGZB-4D | Dimmer | Zigbee | Nue Zigbee Dimmer | Show | |
| Nue | Zigbee Fan Contoller | HGZB-FS | Fan Controller | Zigbee | Nue Zigbee Fan Controller | Show | |
| Nue | Zigbee Scene Contoller | HGZB-1S, HGZB-2S, HGZB-4S | Button Controller | Zigbee | Nue Zigbee Scene Controller | Show | |
| Nue | Zigbee Switch | HGZB-01A | Switch | Zigbee | Nue Zigbee Switch | Show | |
| NYCE | Ceiling Motion Sensor | NCZ-3043-HA | Motion Sensor | Zigbee | NYCE Motion Sensor Series | Show | |
| NYCE | Curtain Motion Sensor | NCZ-3045-HA | Motion Sensor | Zigbee | NYCE Motion Sensor Series | Show | |
| NYCE | Door/Window Sensor | NCZ-3011-HA | Contact Sensor | Zigbee | NYCE Contact Sensor | Show | Amazon |
| NYCE | Garage Door (Tilt) Sensor | NCZ-3014-HA | Contact Sensor | Zigbee | NYCE Iris Tilt Sensor | Show | |
| NYCE | Motion Sensor | NCZ-3041-HA | Motion Sensor | Zigbee | NYCE Motion Sensor Series | Show | |
| Onesti Products AS | Touch Prolock | Touch Prolock | Lock | Zigbee | Generic ZigBee Lock | ||
| Onkyo | Audio Video Receiver | Any with Ethernet port | Audio Video Receiver | LAN | Onkyo AVR | Show | Amazon |
| Onvis | Onvis Smart Plug | Outlet / Plug | Matter | Generic Matter Outlet | |||
| Orbit | 12-Station Sprinkler Controller | 27396 | Irrigation Controller | Zigbee | Zigbee Orbit 12-Station Sprinkler Controller | Show | |
| Orbit | Smart Hose Faucet Timer | 27087 | Irrigation Controller | Zigbee | Orbit Hose Water Timer | Show | |
| Orein | Matter Smart Bulb | Bulb | Matter | Generic Matter RGBW Light | |||
| Orvibo | Motion Sensor | SN11 | Motion Sensor | Zigbee | Generic Zigbee Motion Sensor | Show | |
| Osram | Lightify Flex RGBW | 73698 | Bulb | Zigbee | Generic Zigbee RGBW Light | Show | Amazon |
| Osram | Lightify LED Classic B40 Tunable White 60W | Bulb | Zigbee | Generic Zigbee CT Bulb (dev) | Show | ||
| Osram | Lightify LED Flood BR30 Tunable White | Bulb | Zigbee | Generic Zigbee CT Bulb (dev) | Show | ||
| Osram | Lightify LED Recessed Kit RT 5/6 Tunable | Bulb | Zigbee | Generic Zigbee CT Bulb (dev) | Show | ||
| Osram | Lightify LED Tunable White 60W | Bulb | Zigbee | Generic Zigbee CT Bulb (dev) | Show | ||
| Osram | Smart Outdoor Plug | G11028081 | Outlet / Plug | Zigbee | Generic Zigbee Outlet | Show | |
| Osram | Smart+ Classic E27 Multicolor | Bulb | Zigbee | Advanced Zigbee RGBW Bulb | Show | ||
| PEQ | Contact Sensor | 3300 | Contact Sensor | Zigbee | Generic Zigbee Contact Sensor | Show | |
| PEQ | Moisture Sensor | 3315 | Water Sensor | Zigbee | Generic Zigbee Moisture Sensor | Show | |
| PEQ | Motion Sensor | 3305 | Motion Sensor | Zigbee | Generic Zigbee Motion Sensor | Show | |
| Philio | Philio PST02 | PST02 | Multisensor | Z-Wave | Philio PST02 | Show | |
| Philips Hue | Bloom Lights | Bulb | Zigbee | Generic Zigbee RGB Light | Show | Amazon | |
| Philips Hue | Bridge | Bridge | LAN | Hue Bridge Integration (app) | Show | Amazon | |
| Philips Hue | Dimmer Switch | 73698 | Button Controller | Zigbee | Philips Dimmer Button Controller | Show | |
| Philips Hue | Dimmer Switch V2 | 562777 | Button Controller | Zigbee | Philips Dimmer Button Controller V2 | Show | |
| Philips Hue | Indoor Motion Sensor V2 | 9290030675 | Motion Sensor | Zigbee | Hue Motion Sensor | Show | |
| Philips Hue | Living Colors Lights | Bulb | Zigbee | Generic Zigbee RGB Light | Show | ||
| Philips Hue | Lux | Bulb | Zigbee | Generic Zigbee RGBW Light | Show | ||
| Philips Hue | Motion Sensor | 473389 | Motion Sensor | Zigbee | Hue Motion Sensor | Show | Amazon |
| Philips Hue | Outdoor Motion Sensor | 541730 | Motion Sensor | Zigbee | Hue Motion Sensor | Show | |
| Philips Hue | Philips wall switch module | RDM001 | Button Controller | Zigbee | Philips wall switch module | Show | |
| Philips Hue | Smart Button | 046677553715 | Button Controller | Zigbee | Hue Smart Button | Show | Amazon |
| Philips Hue | Smart Plug | 046677552343 | Outlet / Plug | Zigbee | Generic Zigbee Outlet | Show | |
| Philips Hue | Strip Lights | Bulb | Zigbee | Generic Zigbee RGB Light | Show | ||
| Philips Hue | White Ambiance | Bulb | Zigbee | Generic Zigbee CT Bulb (dev) | Show | ||
| Philips Hue | White and Color Ambiance Bulb | Bulb | Zigbee | Advanced Zigbee RGBW Bulb | Show | ||
| Philips Hue | White and Color Ambiance LightStrip | Bulb | Zigbee | Advanced Zigbee RGBW Bulb | Show | ||
| Philips Wiz | Wi-Fi Wiz Connected Smart LED Light Bulb | Bulb | LAN | Wiz Integration (app) | Show | ||
| Philips Wiz | Wi-Fi Wiz Wireless Connected Smart Plug | Outlet / Plug | LAN | Wiz Integration (app) | Show | ||
| Pioneer | Audio Video Receiver | Any with Ethernet port | Audio Video Receiver | LAN | Pioneer AVR | Show | Amazon |
| Powely | Thermostat | Thermostat | Z-Wave | Generic Z-Wave Thermostat | Show | ||
| Qubino | EU Smart Meter | XMNHTD1 | Energy Meter | Z-Wave | Qubino Smart Meter | Amazon | |
| Qubino | EU version 3-Phase Smart Meter | ZMNHXD1 | Energy Meter | Z-Wave | Qubino 3-Phase Smart Meter | ||
| Qubino | EU version Din Dimmer | ZMNHSD1 | Dimmer | Z-Wave | Qubino DinDimmer | ||
| Qubino | EU version Flush Dimmer 0-10V | ZMNHVD1 | Dimmer | Z-Wave | Qubino Flush Dimmer 0-10V | ||
| Qubino | EU version Flush On/Off Thermostat 2 | ZMNKID1 | Thermostat | Z-Wave | Qubino Flush Thermostat 2 | ||
| Qubino | EU version Luxy Smart Light | ZMNHQD1 | Bulb | Z-Wave | Qubino Luxy Smart Light | ||
| Qubino | EU version Luxy Smart Switch | ZMNKAD1 | Switch | Z-Wave | Qubino Luxy Smart Switch | ||
| Qubino | Flush 1 Relay | ZMNHAD3 | Relay | Z-Wave | Qubino 1 Relay Module | Show | Amazon |
| Qubino | Flush 1D Relay | ZMNHND3 | Relay | Z-Wave | Qubino 1D Relay Module | Show | Amazon |
| Qubino | Flush 2 Relay | ZMNHBD3 | Relay | Z-Wave | Qubino 2 Relay Module | Show | Amazon |
| Qubino | Flush Dimmer | ZMNHDD3 | Dimmer | Z-Wave | Qubino Dimmer Module | Show | Amazon |
| Qubino | Flush ON/OFF Thermostat | ZMNHID3 | Thermostat | Z-Wave | Qubino Thermostat Module | Show | |
| Qubino | Flush Shutter | ZMNHCD3 | Relay | Z-Wave | Qubino Shutter Module | Show | Amazon |
| Qubino | Flush Shutter DC | ZMNHOD3 | Relay | Z-Wave | Qubino Shutter Module | Show | Amazon |
| Qubino | Mini Dimmer | ZMNHHD3 | Dimmer | Z-Wave | Qubino Mini Dimmer | Show | Amazon |
| Quotra | Quotra Wireless Smart Dimmer | B07CVL9SZF | Dimmer | Zigbee | Generic Zigbee Dimmer | Show | |
| Rachio | Smart Sprinkler Controller | Irrigation Controller | Hidden | Rachio Integration (app) | Amazon | ||
| Radio | CT100 Thermostat | CT100 | Thermostat | Z-Wave | Generic Z-Wave Thermostat | Show | Amazon |
| Radio | CT101 Thermostat | CT101 | Thermostat | Z-Wave | Radio Thermostat | Show | Amazon |
| Radio | Thermostat Z-Wave USNAP Module | Thermostat | Z-Wave | Generic Z-Wave Thermostat | Amazon | ||
| Remotec | ZFM-80 Relay / Fixture Switch | ZFM-80 | Relay | Z-Wave | Remotec ZFM-80 | Show | |
| Remotec | ZRC-90 Button Controller | ZRC-90 | Button Controller | Z-Wave | Remotec ZRC-90 | Show | |
| Remotec | ZXT600 AC Controller | ZXT600 | Thermostat | Z-Wave | Remotec Z-Wave-to-AC IR Extender ZXT600 | ||
| RGBgenie | 3 Scene Color Touch Panel and Dimmer | ZB-3009, ZB-3010 | Dimmer | Zigbee | RGBGenie Controller ZB-3009/10 | Show | |
| RGBgenie | 3 Zone Color Touch Panel | ZB-5027 | Button Controller | Zigbee | RGBgenie Controller ZB-3027 | Show | |
| RGBgenie | 4 Channel Dimming Controller | ZB-1003 | Dimmer | Zigbee | RGBgenie Micro Zigbee Dimmer | Show | |
| RGBgenie | 4 Zone 2 Scene Remote | ZB-5004 | Button Controller | Zigbee | RGBGenie Controller ZB-5004 | Show | |
| RGBgenie | 5 Zone Remote and Dimmer | ZB-5001 | Button Controller | Zigbee | RGBgenie Button Controller | Show | |
| RGBgenie | Color Micro Remote with single scene recall | ZB-5122 | Button Controller | Zigbee | RGBgenie Controller ZB-5122 | Show | |
| RGBgenie | Color Remote | ZB-5028 | Button Controller | Zigbee | RGBgenie Controller ZB-5028 | Show | |
| RGBgenie | Micro Controller and Lamp Module | ZW-4001 | Dimmer | Z-Wave | RGBgenie Z-Wave Micro Controller | Show | |
| RGBgenie | Micro Switch | ZW-4004 | Switch | Z-Wave | RGBgenie Micro Switch ZW-4004 | ||
| RGBgenie | Remote | ZW-5002 | Button Controller | Z-Wave | null (app) | ||
| RGBgenie | RGBW Color Controller | ZB-1025 | Dimmer | Zigbee | RGBgenie Micro Zigbee Dimmer | Show | |
| RGBgenie | RGBW Color Controller | ZW-1002 | Dimmer | Z-Wave | Generic Z-Wave Smart Dimmer | Show | Amazon |
| RGBgenie | Single Channel Micro Controller and Lamp Module | ZB-4003 | Switch | Zigbee | Generic Zigbee Switch | Show | |
| RGBgenie | Single Channel Trailing Edge Dimmer | ZB-4002 | Dimmer | Zigbee | RGBgenie Micro Zigbee Dimmer | Show | Amazon |
| RGBgenie | Single color controller | ZW-1001 | Dimmer | Z-Wave | Generic Z-Wave Smart Dimmer | Show | |
| RGBgenie | Single Color Controller Panel | ZB-3026 | Button Controller | Zigbee | RGBgenie Controller ZB-3026 | Show | |
| RGBgenie | Single Color Wall Mounted Remote Controller | ZB-5121 | Button Controller | Zigbee | RGBgenie Controller ZB-512x | Show | |
| Ring | Flood & Freeze Sensor | 4SF1S8-0EN0 | Water Sensor | Z-Wave | Ring Flood Sensor | Amazon | |
| Ring | Outdoor Contact Sensor | Contact Sensor | Z-Wave | Ring Alarm Contact Sensor G2 | |||
| Ring | Outdoor Siren | B08LYCYZFY | Siren | Z-Wave | Ring Outdoor Siren | ||
| Ring | Ring Alarm Contact Sensor V1 | 4SD1S70EN0 | Contact Sensor | Z-Wave | Ring Alarm Contact Sensor | Show | Amazon |
| Ring | Ring Alarm Contact Sensor V2 | 4SD2SZ0EN0 | Contact Sensor | Z-Wave | Ring Alarm Contact Sensor G2 | Amazon | |
| Ring | Ring Alarm Hardwired Retrofit Kit | 4AW1SZ0EN0 | Multisensor | Z-Wave | Ring Alarm Retrofit | Amazon | |
| Ring | Ring Alarm Keypad V1 | 4AK1S70EN0 | Keypad | Z-Wave | Ring Alarm Keypad G1 | ||
| Ring | Ring Alarm Keypad V2 | 4AK1SZ0EN0 | Keypad | Z-Wave | Ring Alarm Keypad G2 | Amazon | |
| Ring | Ring Alarm Motion Sensor V1 | 4SP1S70EN0 | Motion Sensor | Z-Wave | Ring Alarm Motion Sensor | Show | |
| Ring | Ring Alarm Motion Sensor V2 | 4SP2SZ0EN0 | Motion Sensor | Z-Wave | Ring Alarm Motion Sensor G2 | Amazon | |
| Ring | Ring Alarm Range Extender V1 | 4AR1S70EN0 | Repeater | Z-Wave | Ring Alarm Range Extender | Show | |
| Ring | Ring Alarm Smoke/CO Listener | 4SS1S80EN0 | Smoke/CO Detector | Z-Wave | Ring Alarm Smoke/CO Listener | Show | Amazon |
| Ring | Ring Glass Break Sensor | Glass Break Sensor | Glass Break Detector | Z-Wave | Ring Glass Break Sensor | ||
| Ring | Ring Outdoor Siren | 5D22E2 | Siren | Z-Wave | Ring Outdoor Siren | Show | |
| Rotel | Rotel AVR | Any with Ethernet Port | Audio Video Receiver | LAN | Rotel AVR | Show | |
| Sage | A19 Bulb | A19 Bulb | Bulb | Zigbee | Generic Zigbee Bulb | Show | |
| Sage | BR30 Bulb | BR30 Bulb | Bulb | Zigbee | Generic Zigbee Bulb | Show | |
| Sage | Doorbell Sensor | Button Controller | Zigbee | SAGE Doorbell Sensor | Show | ||
| Sage | Light Switch Controller | Button Controller | Zigbee | SAGE Light Switch Controller | Show | ||
| Salus | Smart Plug | SP600 | Outlet / Plug | Zigbee | Generic Zigbee Outlet | Show | |
| Samotech | Zigbee Control Module | MS104Z | Switch | Zigbee | Generic Zigbee Switch | Show | |
| Samsung SmartThings | Button V5 | IM6001-BTP | Button Controller | Zigbee | Samsung Zigbee Button | Show | |
| Samsung SmartThings | Motion Sensor V5 | IM6001-MTP | Motion Sensor | Zigbee | Generic Zigbee Motion Sensor | Show | |
| Samsung SmartThings | Multi Sensor V5 | IM6001-MPP | Contact Sensor | Zigbee | SmartThings Multipurpose Sensor V5 | Show | |
| Samsung SmartThings | Outlet (2017 Model) | F-OUT-US-2 | Outlet / Plug | Zigbee | Generic Zigbee Outlet | Show | |
| Samsung SmartThings | Outlet V5 | IM6001-OTP | Outlet / Plug | Zigbee | Generic Zigbee Outlet | Show | |
| Samsung SmartThings | Water Leak Sensor V5 | IM6001-WLP | Water Sensor | Zigbee | Generic Zigbee Moisture Sensor | Show | |
| Samsung SmartThings | Zigbee Smart Plug | ZG9021A | Outlet / Plug | Zigbee | Generic Zigbee Outlet | Show | |
| Sengled | Button Controller | E1E-G7F | Button Controller | Zigbee | Sengled Button Controller | Show | |
| Sengled | Element Classic Bulb | E11-G13, E11-G14 | Bulb | Zigbee | Sengled Element Classic | Show | Amazon |
| Sengled | Element Multicolor Bulb | E11-N1EA | Bulb | Zigbee | Sengled Element Color Plus | Show | Amazon |
| Sengled | Element Plus Bulb | Z01-A19NAE26 | Bulb | Zigbee | Sengled Element Plus | Show | |
| Sengled | Multicolor Light Strip | E1G-G8E | Bulb | Zigbee | Sengled Element Color Plus | Show | |
| Sengled | Sengled Element Classic with motion | E13-N11 | Bulb | Zigbee | Sengled Element Classic with motion | Show | |
| Sengled | Smart Light Bulb | Bulb | Matter | Generic Matter RGBW Light | |||
| Sengled | Smart Plug | E1C-NB7 | Outlet / Plug | Zigbee | Generic Zigbee Outlet | Show | |
| Sengled | Smart Plug | E1C-NB6 | Outlet / Plug | Zigbee | Generic Zigbee Outlet | Show | Amazon |
| Sengled | Smart Window and Door Sensor | E1D-G73 | Contact Sensor | Zigbee | Generic Zigbee Contact Sensor | Show | Amazon |
| Sensative | Strips Comfort | Temperature Sensor | Z-Wave | Strips Multi-Sensor | Show | ||
| Sensative | Strips Drips | Water Sensor | Z-Wave | Strips Multi-Sensor | Show | Amazon | |
| Sensative | Strips Guard | Contact Sensor | Z-Wave | Generic Z-Wave Contact Sensor | Show | ||
| Shelly | Shelly 1 | Switch | LAN | Shelly WiFi Switch | Show | Amazon | |
| Shelly | Shelly 1PM | Switch | LAN | Shelly WiFi Switch | Show | Amazon | |
| Shelly | Shelly 2.5 | Switch | LAN | Shelly WiFi Switch | Show | Amazon | |
| Shelly | Shelly Bulb | Bulb | LAN | Shelly WiFi RGBW Bulb | Show | ||
| Shelly | Shelly DUO | Bulb | LAN | Shelly WiFi CT Bulb | Show | Amazon | |
| Shelly | Shelly Plug | Outlet / Plug | LAN | Shelly WiFi Switch | Show | ||
| Shelly | WiFi Dimmer | Dimmer | LAN | Shelly WiFi Dimmer | Show | Amazon | |
| Shelly | WiFi Switch | Switch | LAN | Shelly WiFi Switch | Show | ||
| Sinopé | In-Wall Outlet | SP2610ZB | Outlet / Plug | Zigbee | Generic Zigbee Outlet | Show | |
| Sinopé | Multi Controller | MC3100ZB | Multi Controller | Zigbee | Sinope Multi-controller | Show | |
| Sinopé | Sinope DM2550ZB Dimmer | DM2550ZB | Dimmer | Zigbee | Sinope DM2550ZB Dimmer | Show | |
| Sinopé | Smart Dimmer | DM2500ZB | Dimmer | Zigbee | Sinope Dimmer | Show | Amazon |
| Sinopé | Smart Double-Pole Thermostat | TH1500ZB | Thermostat | Zigbee | Sinope TH1400ZB Thermostat | Show | |
| Sinopé | Smart Electrical Load Controller | RM3250ZB | Switch | Zigbee | Sinope load controller | Show | |
| Sinopé | Smart Floor Heating Thermostat | TH1300ZB | Thermostat | Zigbee | Sinope TH1300ZB Thermostat | Show | |
| Sinopé | Smart Low Voltage Thermostat | TH1400ZB | Thermostat | Zigbee | Sinope TH1400ZB Thermostat | Show | Amazon |
| Sinopé | Smart Plug | SP2600ZB | Outlet / Plug | Zigbee | Generic Zigbee Outlet | Show | |
| Sinopé | Smart Switch | SW2500ZB | Switch | Zigbee | Sinope Switch | Show | |
| Sinopé | Smart Thermostat for Electric Heating | TH1123ZB-G2 | Thermostat | Zigbee | Sinope TH1123ZB-G2 Thermostat | Show | |
| Sinopé | Smart thermostat for electric heating | TH1123ZB, TH1124ZB | Thermostat | Zigbee | Sinope TH1124ZB (4KW) Thermostat | Show | Amazon |
| Sinopé | Smart Water Leak Detector | WL4200 | Water Sensor | Zigbee | Sinope Moisture Sensor | Show | Amazon |
| Sinopé | Smart Water Leak Detector with Sensor | WL4200S | Water Sensor | Zigbee | Sinope Moisture Sensor | Show | |
| Sinopé | Smart Water Valve | VA4200WZ, VA4220ZB | Valve | Zigbee | Sinope water valve | Show | |
| Sinopé | Tank Level Monitor | LM4110-ZB | Multisensor | Zigbee | Sinope Tank Level Monitor | Show | |
| Sinopé | Water Heater Controller | RM3500ZB | Multi Controller | Zigbee | Sinope water heater controller | Show | |
| Sinopé | Zigbee Water Valve | VA4200WZ | Water Sensor | Zigbee | Sinope water valve | Show | |
| SmartThings | Arrival/Presence Sensor V4 | Presence Sensor | Zigbee | SmartThings Presence Sensor V4 | Show | ||
| SmartThings | Contact Sensor | 3300-S | Contact Sensor | Zigbee | Generic Zigbee Contact Sensor | Show | |
| SmartThings | Humidity Sensor | 3310-S | Humidity Sensor | Zigbee | SmartThings Humidity Sensor | Show | |
| SmartThings | Motion Sensor V2 | Motion Sensor | Zigbee | Generic Zigbee Motion Sensor | Show | ||
| SmartThings | Motion Sensor V3 | Motion Sensor | Zigbee | Generic Zigbee Motion Sensor | Show | ||
| SmartThings | Motion Sensor V4 | Motion Sensor | Zigbee | Generic Zigbee Motion Sensor | Show | ||
| SmartThings | Multi Sensor (2015 model) | F-SS-MULT-001 | Contact Sensor | Zigbee | SmartSense Multi Sensor V4 | Show | |
| SmartThings | Multi Sensor (2016 model) | F-MLT-US-2 | Contact Sensor | Zigbee | SmartSense Multi Sensor V4 | Show | |
| SmartThings | Multi Sensor V4 | STS-MLT-250 | Contact Sensor | Zigbee | SmartSense Multi Sensor V4 | Show | |
| SmartThings | SmartSense Moisture Sensor | Water Sensor | Zigbee | Generic Zigbee Moisture Sensor | Show | ||
| SmartThings | SmartSense Motion Sensor | Motion Sensor | Zigbee | Generic Zigbee Motion Sensor | Show | ||
| SmartThings | SmartSense Presence Sensor V2 | Presence Sensor | Zigbee | SmartThings Presence Sensor V2 | Show | ||
| SmartThings | Water Leak Sensor v4 (2015) | Water Sensor | Zigbee | Generic Zigbee Moisture Sensor | Show | ||
| SmartWings | Shade | Zigbee Shade | Shade Controller | Zigbee | Smartwings Zigbee Shade | ||
| SmartWings | SmartWings Matter Shade | Shade | Matter | SmartWings Matter Shade | |||
| Somfy | 2 Button Controller | Button Controller | Z-Wave | Somfy 2 Button Controller | |||
| Sonoff | S31 Lite Zigbee Smart Plug US | S31 Lite Zigbee | Outlet / Plug | Zigbee | Generic Zigbee Outlet | Show | |
| Sonoff | Temperature Humidity Sensor | SNZB-02D | Temperature Sensor | Zigbee | Generic Zigbee Temperature/Humidity | ||
| Sonoff | ZBMINI Relay Module | ZBMINI | Switch | Zigbee | Generic Zigbee Switch | Show | |
| Sonoff | Zigbee Button Controller | SNZB-01 | Button Controller | Zigbee | Sonoff Zigbee Button Controller | Show | |
| Sonoff | Zigbee Contact Sensor | SNZB-04 | Contact Sensor | Zigbee | Sonoff Zigbee Contact Sensor | Show | |
| Sonoff | Zigbee Motion Sensor | SNZB-03 | Motion Sensor | Zigbee | Generic Zigbee Motion Sensor (no temp) | Show | |
| Sonoff | Zigbee Temperature/Humidity Sensor | SNZB-02 | Temperature Sensor | Zigbee | Sonoff Zigbee Temperature/Humidity Sensor | Show | |
| Sonos | Media Player | All Models | Speaker | LAN | Sonos Integration (app) | Show | Amazon |
| Sunricher | 4 Channels CV 100W Dimmable Driver | SRP-ZG9105-24-100CVF | Dimmer | Zigbee | Advanced Zigbee RGBW Bulb | Show | |
| Sunricher | 4 in 1 Universal LED Controller | ZG1029-5C | Dimmer | Zigbee | Advanced Zigbee RGBW Bulb | Show | |
| Sunricher | AC Phase-Cut Dimmer | ZV9101SAC-HP | Dimmer | Z-Wave | RGBGenie Z-Wave Micro Controller | ||
| Sunricher | Ceiling Mount Occupancy Sensor | SR-ZG9030A-MW | Motion Sensor | Zigbee | Sunricher MW Motion Sensor | Show | |
| Sunricher | Dim Remote Control | ZV9001K12 | Button Controller | Z-Wave | RGBGenie Z-Wave Remote ZW-5009 | ||
| Sunricher | Dimmer controller | ZG9001K12-DIM-Z3 | Button Controller | Zigbee | Sunricher Zigbee Wireless Dimmer Switch | Show | |
| Sunricher | Dimmer Module | ZG9101SAC-HP-Dimmer | Dimmer | Zigbee | RGBGenie Z-Wave Micro Controller | Show | |
| Sunricher | Door/Window Sensor | ZV9010A | Contact Sensor | Z-Wave | Generic Z-Wave Door Window Sensor | ||
| Sunricher | EU Zigbee RGBW panel | ZGRC-TEUR-001 | Button Controller | Zigbee | RGBgenie Controller ZB-3027 | Show | |
| Sunricher | Fixture Integrated Occupancy Sensor | SR-ZG9032A-MW | Motion Sensor | Zigbee | Sunricher MW Motion Sensor | Show | |
| Sunricher | In-Wall Smart Switch | ZV9100 | Switch | Z-Wave | RGBgenie Micro Switch ZW-4004 | ||
| Sunricher | IP65 Occupancy Sensor | SR-ZG9031A-MW | Motion Sensor | Zigbee | Sunricher MW Motion Sensor | Show | |
| Sunricher | Outlet Strip | HK-LN-SOCKET-A EU | Switch | Zigbee | Generic Zigbee Mult-Endpoint Switch | Show | |
| Sunricher | Power reporting outlet | HK-PLUG-A EU | Outlet / Plug | Zigbee | Generic Zigbee Outlet | Show | |
| Sunricher | Relay Module | ZG9101SAC-HP-Switch | Switch | Zigbee | Generic Zigbee Switch | Show | |
| Sunricher | Relay Module | ZV9101SAC-HP-Switch | Switch | Z-Wave | RGBGenie Z-Wave Micro Switch | ||
| Sunricher | Single color 4-Group remote | ZG9001K8-DIM | Button Controller | Zigbee | RGBgenie Button Controller | Show | |
| Sunricher | Single color 8 button controller | ZG2833K8_EU05 | Button Controller | Zigbee | RGBgenie Button Controller | Show | |
| Sunricher | Single color remote | ZG9001K5-5C | Button Controller | Zigbee | RGBgenie Controller ZB-5122 | Show | |
| Sunricher | Single color remote secondary controller | ZV9001K12-DIM-Z4 | Button Controller | Z-Wave | RGBGenie Z-Wave Remote | ||
| Sunricher | Single color remote secondary controller light switch | ZV9001K8-DIM-G4 | Button Controller | Z-Wave | Generic Z-Wave Plus Button Controller | ||
| Sunricher | Smart Plug | ZV9020A | Outlet / Plug | Z-Wave | Sunricher SR-ZV9020A Z-Wave Smart Plug | ||
| Sunricher | Zigbee Smart Plug | ZG9021A | Outlet / Plug | Zigbee | Generic Zigbee Outlet | Show | |
| Sylvania | Smart+ 4 Button Switch | 74099 | Button Controller | Zigbee | Lightify Smart Switch | Show | |
| Sylvania | Smart+ A19 Dimmable | Bulb | Zigbee | Generic Zigbee Bulb | Show | ||
| Sylvania | Smart+ A19 RGBW | Bulb | Zigbee | Generic Zigbee RGBW Light | Show | ||
| Sylvania | Smart+ BR30 RGBW | 74988 | Bulb | Zigbee | Generic Zigbee RGBW Light | Show | |
| Sylvania | Smart+ Contact and Temp Sensor | 74388 | Contact Sensor | Zigbee | Generic Zigbee Contact Sensor | Show | |
| Sylvania | Smart+ Dimmer | 73743 | Button Controller | Zigbee | Sylvania Dimmer Switch Button Controller | Show | |
| Sylvania | Smart+ Flex RGBW | 74521 | Bulb | Zigbee | Generic Zigbee RGBW Light | Show | |
| Sylvania | Smart+ Flex SL RGBW | Bulb | Zigbee | Generic Zigbee RGBW Light | Show | ||
| Sylvania | Smart+ Motion Sensor | 72923 | Motion Sensor | Zigbee | Generic Zigbee Motion Sensor | Show | |
| Sylvania | Smart+ Outdoor RGBW Flex | 73685 | Bulb | Zigbee | Generic Zigbee RGBW Light | Show | Amazon |
| Sylvania | Smart+ Outlet | 72922 | Outlet / Plug | Zigbee | Generic Zigbee Outlet | Show | |
| Sylvania | Smart+ RT5/6 RGBW | Bulb | Zigbee | Generic Zigbee RGBW Light | Show | ||
| Tapo | Matter Smart Plug | Outlet / Plug | Matter | Generic Matter Outlet | |||
| Tapo | Smart Light Bulb | Bulb | Matter | Generic Matter RGBW Light | |||
| Tapo | Smart Wi-Fi Light Switch | S505 | Switch | Matter | Generic Matter Switch | ||
| Tapo | Tapo Smart Matter Outdoor Dual Plug | Outlet / Plug | Matter | Tapo Smart matter Outdoor Dual Plug | |||
| Telguard | Garage Door Control Switch | GDC1 | Switch | Z-Wave | Generic Z-Wave Switch | Show | Amazon |
| Telldus | Outlet Switch | TZWP-100 | Outlet / Plug | Z-Wave | Generic Z-Wave Smart Switch | Show | |
| Telstra | Smart Power Plug | SZ-ESW01-AU | Outlet / Plug | Zigbee | Generic Zigbee Outlet | Show | |
| Third Reality | Multi-Function Night Light | 3RSNL02043Z | Multi Controller | Zigbee | Third Reality Multi-Function Night Light | ||
| Third Reality | Reality Switch | Switch | Zigbee | Generic Zigbee Switch | Show | Amazon | |
| Third Reality | Smart Plug | 3RSP02028BZ | Outlet / Plug | Zigbee | Generic Zigbee Outlet | ||
| Third Reality | Temperature Humidity | 3RTHS0224BZ | Temperature Sensor | Zigbee | Generic Zigbee Temperature/Humidity | ||
| Third Reality | Third Reality door sensor | 3RDS17BZ | Contact Sensor | Zigbee | Generic Zigbee Contact Sensor (no temp) | Show | |
| Third Reality | Third Reality Matter Multi-Function Night Light | Multi-Function | Matter | Third Reality Matter Multi-Function Night Light | |||
| Third Reality | Third Reality motion sensor | 3RMS16BZ | Motion Sensor | Zigbee | Generic Zigbee Motion Sensor (no temp) | Show | |
| Third Reality | Third Reality Smart Blind | 3RSB015BZ | Shade Controller | Zigbee | Generic Zigbee Shade | Show | |
| Third Reality | Third Reality Smart Button | 3RSB22BZ | Button Controller | Zigbee | Third Reality Smart Button | Show | |
| Third Reality | Third Reality Smart Plug | 3RSP019BZ | Outlet / Plug | Zigbee | Generic Zigbee Outlet | Show | |
| Third Reality | Third Reality Switch | 3RSS009Z | Switch | Zigbee | null (app) | Show | |
| Third Reality | Third Reality Temp Humidity Sensor | Humidity Sensor | Zigbee | Generic Zigbee Temperature/Humidity Sensor | Show | ||
| Third Reality | water sensor | 3RWS18BZ | Water Sensor | Zigbee | Generic Zigbee Moisture Sensor (no temp) | ||
| TKB | TKB Dimmer Socket | TZ67E | Dimmer | Z-Wave | Generic Z-Wave Smart Dimmer | Show | |
| TP-Link | Smart Home Sensor | MS100 | Motion Sensor | Zigbee | Generic Zigbee Motion Sensor (no temp) | ||
| Trane | Thermostat | XR524 | Thermostat | Z-Wave | Generic ZWave Thermostat | ||
| Tuya Smart | ODM/OEM outlet | Outlet / Plug | Zigbee | Generic Zigbee Outlet | Show | ||
| Tuya Smart | Smart Surge Protector | TS011F | Outlet / Plug | Zigbee | Generic Zigbee Multi-Endpoint Switch | ||
| Tuya Smart | water sensor | Water Sensor | Zigbee | Generic Zigbee Moisture Sensor (no temp) | |||
| Tuya Smart | Zigbee Motion Sensor | ZXZPIR-02 | Motion Sensor | Zigbee | Zigbee Motion Sensor (no temp) | Show | |
| Tuya Smart | Zigbee Touch Wall Switch (1,2,3 and 4 gang) | Z801-01US, Z802-01US, SK-Z803-01US | Switch | Zigbee | Generic Zigbee Multi-Endpoint Switch | Show | |
| Uascent | inwall Matter micro | V-MT-S01 | Switch | Matter | Generic Matter Switch | ||
| Uascent | inwall Matter micro | V-MT-S02 | Switch | Matter | Generic Matter Multi-Endpoint Switch | ||
| Ultraloq | U-Bolt Pro Z-Wave | Lock | Z-Wave | Generic Z-Wave Lock | |||
| UltraPro | Smart Dimmer | 39351 | Dimmer | Z-Wave | GE Enbrighten Z-Wave Smart Dimmer | Amazon | |
| UltraPro | Smart Switch | 39348, 39354 | Switch | Z-Wave | Generic Z-Wave Plus Scene Switch | Amazon | |
| Utilitech | Siren | TSE07 | Siren | Z-Wave | Utilitech | Show | |
| Vesternet | Zigbee 8 Button Wall Controller | VES-ZB-WAL-012 | Button Controller | Zigbee | RGBgenie Button Controller | Show | |
| Vision | Siren | ZM1601US-3, ZM1601US-5 | Siren | Z-Wave | Linear/Vision Siren | Show | |
| Vision | Vision Shock Sensor | ZS5101 | Acceleration Sensor | Z-Wave | Generic Z-Wave Acceleration Sensor | Show | |
| Visonic | Glass Break Detector | Glass Break Detector | Zigbee | Generic Zigbee Glass Break Sensor | |||
| Visonic | Motion Detector | MP-840 | Motion Sensor | Zigbee | Generic Zigbee Motion Sensor | ||
| Visonic | Window/Door Sensor | MCT-340 E | Contact Sensor | Zigbee | Generic Zigbee Contact Sensor | Show | Amazon |
| Visonic | Window/Door Sensor | MCT-340 SMA | Contact Sensor | Zigbee | Generic Zigbee Contact Sensor | Show | |
| Visonic | Window/Door Sensor | MCT-370 SMA | Contact Sensor | Zigbee | Generic Zigbee Contact Sensor | Show | |
| Vuytret | Smart Plug | Outlet / Plug | Matter | Generic Matter Outlet | |||
| Wally | Shutoff Valve | Shutoff Valve | Valve | Zigbee | Wally shutoff valve | Show | |
| Wally | Wally Sensor | Wally Sensor | Multisensor | Zigbee | Wally Multisensor | Show | |
| WaterCop | Shutoff Valve | WAT171021 | Valve | Z-Wave | Generic Z-Wave Valve | Show | |
| Wireless | Smoke Detector | ZWN-SD | Smoke/CO Detector | Z-Wave | Generic Z-Wave Smoke Detector | Show | |
| Wiz | Color Smart Bulb | Bulb | Matter | Generic Matter RGBW Light | |||
| Wiz | Tunable White Smart Bulb | Bulb | Matter | Generic Matter CT Light | |||
| Wiz | Wi-Fi Wiz Connected Smart LED Light Bulb | Bulb | LAN | Wiz Integration (app) | Show | ||
| Wiz | Wi-Fi Wiz Wireless Connected Smart Dimmer | Dimmer | LAN | Wiz Integration (app) | Show | ||
| Wiz | Wi-Fi Wiz Wireless Connected Smart Plug | Outlet / Plug | LAN | Wiz Integration (app) | Show | ||
| Xfinity | Xfinity 3400-X Keypad | 3400 | Keypad | Zigbee | Centralitle Keypad | Show | |
| Yale | Assure Connected | YRD226 | Lock | Z-Wave | Generic Z-Wave Lock | Show | Amazon |
| Yale | Assure Keypad Deadbolt | YRD216 | Lock | Zigbee | Generic Zigbee Lock | Show | Amazon |
| Yale | Assure Lock 2 | YRD420 | Lock | Z-Wave | Generic Z-Wave Lock | ||
| Yale | Assure Lock 2 | YRD450 | Lock | Z-Wave | Generic Z-Wave Lock | ||
| Yale | Conexis L1 | Conexis L1 | Lock | Z-Wave | Yale Conexis L1 Z-Wave Lock | Show | |
| Yale | Lever Lock | YRL236, YRL256 | Lock | Zigbee | Generic Zigbee Lock | Show | Amazon |
| Yale | Push Button Lever Lock | YRD210 | Lock | Zigbee | Generic Zigbee Lock | Show | Amazon |
| Yale | Yale Assure Lock 2 | YRD450-BLE-619 | Lock | Z-Wave | Generic Z-Wave Lock | ||
| Yale | Yale Assure Lock 2 | YRD430-BLE-BSP | Lock | Z-Wave | Generic Z-Wave Lock | ||
| Yale | Yale Assure Lock 2 | YRD410-BLE-BSP | Lock | Z-Wave | Generic Z-Wave Lock | ||
| Yale | Yale Assure Lock 2 | YRD420-BLE-619 | Lock | Z-Wave | Generic Z-Wave Lock | ||
| Yale | Yale Assure Lock SL | Lock | Z-Wave | Generic Z-Wave Lock | Show | Amazon | |
| Yeelight | Bedside Lamp | Bulb | Integration | Yeelight Integration (app) | Show | ||
| Yeelight | Ceiling 10 | YLXD10YL | Bulb | Integration | Yeelight Integration (app) | Show | |
| Yeelight | Ceiling 15 | YLXD42YL | Bulb | Integration | Yeelight Integration (app) | Show | |
| Yeelight | Ceiling 4 | Bulb | Integration | Yeelight Integration (app) | Show | ||
| Yeelight | Color 6 | Bulb | Integration | Yeelight Integration (app) | Show | ||
| Yeelight | color b bulb | colorb | Bulb | Integration | Yeelight Integration (app) | Show | |
| Yeelight | ColorA | Bulb | Integration | Yeelight Integration (app) | Show | ||
| Yeelight | Mono 5 | YLDP11YL, YLDP12YL | Bulb | Integration | Yeelight Integration (app) | Show | |
| Yeelight | Mono Bulb | Mono Bulb | Bulb | LAN | Yeelight Integration (app) | Show | |
| Yeelight | Smart LED Bulb (Color and CT) | Bulb | Integration | Yeelight Integration (app) | Show | Amazon | |
| Yeelight | Smart LED Bulb (Color) | Bulb | Integration | Yeelight Integration (app) | Show | ||
| Yeelight | Smart LED Bulb (CT) | Bulb | Integration | Yeelight Integration (app) | Show | ||
| Yolax | Shade | Zigbee Shade | Shade Controller | Zigbee | Yolax Zigbee Shade | ||
| Yoolax | Roller Shade | Shade Controller | Zigbee | Generic Zigbee Shade | Show | ||
| Zemismart | 2 Gang Switch | ZM-02-DK | Switch | Zigbee | Nue Zigbee Switch | Show | |
| Zemismart | Zigbee Switch | ZM-01-DK | Switch | Zigbee | Nue Zigbee Switch | Show | |
| Zen | Thermostat | Thermostat | Zigbee | Zen Thermostat | Show | Amazon | |
| Zipato | Bulb 2 | RGBW2 | Bulb | Z-Wave | Zipato Bulb 2 | ||
| Zipato | Siren | PH-PSE02 | Siren | Z-Wave | Zipato Siren | Show | Amazon |
| ZLINK | Appliance Switch | ZL-PA-100 | Outlet / Plug | Z-Wave | Generic Z-Wave outlet | Amazon | |
| ZLINK | In-Wall Dimmer | ZL-WD-100 | Dimmer | Z-Wave | Generic Z-Wave CentralScene Dimmer | Show | Amazon |
| ZLINK | In-Wall Switch | ZL-WS-100 | Switch | Z-Wave | Generic Z-Wave CentralScene Switch | Show | Amazon |
| ZLINK | Plug in Dimmer | ZL-PD-100 | Dimmer | Z-Wave | Generic Z-Wave Plus Dimmer | Amazon | |
| ZLINK | Water Leak and Temperature Sensor | ZL-LD-100 | Water Sensor | Z-Wave | Zlink Water Leak and Temperature Sensor | ||
| Zooz | 0-10V Dimmer | Zen54 | Dimmer | Z-Wave | Zooz Zen54 0-10V Dimmer | ||
| Zooz | 4-in-1 Sensor | ZSE40 | Motion Sensor | Z-Wave | Zooz 4-in-1 Sensor | Show | Amazon |
| Zooz | 4-in-1 Sensor | Multisensor | Z-Wave | Zooz 4-in-1 Sensor New | |||
| Zooz | Dimmer Switch | ZEN22 | Dimmer | Z-Wave | Zooz Central Scene Dimmer | Show | |
| Zooz | Double Relay | Zen52 | Relay | Z-Wave | Zooz Zen52 Double Relay | ||
| Zooz | Dry Contact Relay | Zen51 | Relay | Z-Wave | Zooz Zen51 Dry Contact Relay | ||
| Zooz | Motion and Light Mini Sensor | ZSE09 | Motion Sensor | Z-Wave | Dome Motion Sensor | Show | |
| Zooz | Motion Sensor | ZSE02 | Motion Sensor | Z-Wave | Generic Z-Wave Motion Sensor | Show | |
| Zooz | Motion Sensor ZSE18 | ZSE18 | Motion Sensor | Z-Wave | Zooz Motion Sensor ZSE18 | Show | Amazon |
| Zooz | MultiRelay | ZEN16 | Switch | Z-Wave | Zooz MultiRelay | Show | Amazon |
| Zooz | Outdoor Motion Sensor | ZSE29 | Motion Sensor | Z-Wave | Generic Z-Wave Motion Sensor | Show | Amazon |
| Zooz | Power Strip | ZEN20 | Power Strip | Z-Wave | Zooz Power Strip | Show | |
| Zooz | Power Switch | ZEN15 | Switch | Z-Wave | Zooz Power Switch | Show | Amazon |
| Zooz | Smart Chime | ZSE33 | Doorbell | Z-Wave | Dome Siren | Show | |
| Zooz | Smart Plug | ZEN06 | Outlet / Plug | Z-Wave | Zooz Power Switch | Show | |
| Zooz | Smart Switch | ZEN21 | Switch | Z-Wave | Zooz Central Scene Switch | Show | |
| Zooz | Water Sensor | ZSE30 | Water Sensor | Z-Wave | Dome Leak Sensor | Show | |
| Zooz | Water Valve | ZAC03 | Valve | Z-Wave | Generic Z-Wave Valve | Show | |
| Zooz | Zac36 Ball Valve Controller | Zac36 | Valve | Z-Wave | Zooz Zac36 Ball Valve Controller | Amazon | |
| Zooz | Zen73 S2 Toggle Switch | Zen73 | Switch | Z-Wave | Zooz Zen73 S2 Toggle Switch | ||
| Zooz | Zen74 S2 Toggle Switch | Zen74 | Switch | Z-Wave | Zooz Zen74 S2 Toggle Switch | ||
| Zooz | Zooz 700 Series Dimmer | ZEN72 | Dimmer | Z-Wave | Zooz Zen72 Dimmer | Amazon | |
| Zooz | Zooz 700 Series Dimmer Switch | ZEN77 | Dimmer | Z-Wave | Zooz Zen77 Dimmer | ||
| Zooz | Zooz 700 Series Light Switch | ZEN71 | Switch | Z-Wave | Zooz Zen71 Switch | ||
| Zooz | Zooz 700 Series Scene Controller Switch | ZEN32 | Switch | Z-Wave | Zooz Zen32 Scene Controller | ||
| Zooz | Zooz 700 Series Universal Relay | ZEN17 | Relay | Z-Wave | Zooz Zen17 Universal Relay | Amazon | |
| Zooz | Zooz 700 Series Wall Switch | ZEN76 | Switch | Z-Wave | Zooz Zen76 Switch | ||
| Zooz | Zooz Dimmer Toggle | ZEN24 | Dimmer | Z-Wave | Zooz Central Scene Dimmer | Show | |
| Zooz | Zooz Double Outdoor Plug | ZEN14 | Outlet / Plug | Z-Wave | Zooz ZEN14 Double Outdoor Plug | ||
| Zooz | Zooz Double Switch | ZEN30 | Switch | Z-Wave | Zooz Double Switch | Show | Amazon |
| Zooz | Zooz On/Off Toggle | ZEN23 | Switch | Z-Wave | Zooz Central Scene Switch | Show | |
| Zooz | Zooz Remote Switch | ZEN34 | Button Controller | Z-Wave | Zooz Remote Switch Zen34 | Amazon | |
| Zooz | Zooz RGBW Dimmer | ZEN31 | Dimmer | Z-Wave | Zooz RGBW Dimmer | Show | Amazon |
| Zooz | Zooz S2 Dimmer | ZEN27 | Dimmer | Z-Wave | Zooz Central Scene Dimmer | Show | |
| Zooz | Zooz S2 Multisiren | ZSE19 | Siren | Z-Wave | Zooz S2 Multisiren | Show | |
| Zooz | Zooz S2 On/Off Switch | ZEN26 | Switch | Z-Wave | Zooz Central Scene Switch | Show | Amazon |
| Zooz | Zooz Smart Plug | ZEN04 | Outlet / Plug | Z-Wave | Zooz ZEN04 Smart Plug | ||
| Zooz | Zooz ZEN05 Outdoor Plug | ZEN05 | Outlet / Plug | Z-Wave | Zooz ZEN05 Outdoor Plug | ||
| Zooz | Zooz Zen51 Dry Contact Relay | ZEN51 | Relay | Z-Wave | Zooz Zen51 Dry Contact Relay | Show | |
| Zooz | Zooz Zen52 Double Relay | Zen52 | Relay | Z-Wave | Zooz Zen52 Double Relay | Show | |
| Zooz | Zse41 Open Close XS Sensor | Zse41 | Contact Sensor | Z-Wave | Zooz Zse41 Open Close XS Sensor | ||
| Zooz | Zse42 Water Leak XS Sensor | Zse42 | Water Sensor | Z-Wave | Zooz Zse42 Water Leak XS Sensor | ||
| ZWP | Dimmer | WD-100 | Dimmer | Z-Wave | Generic Z-Wave CentralScene Dimmer | Show | |
| ZWP | Switch | WS-100 | Switch | Z-Wave | Generic Z-Wave CentralScene Switch | Show | |
| Generic/Other | Generic Matter Contact Sensor | Contact Sensor | Matter | Generic Matter Contact Sensor | |||
| Generic/Other | Generic Matter CT Light | Bulb | Matter | Generic Matter CT Light | |||
| Generic/Other | Generic Matter Dimmer | Dimmer | Matter | Generic Matter Dimmer | |||
| Generic/Other | Generic Matter Motion Sensor | Motion Sensor | Matter | Generic Matter Motion Sensor | |||
| Generic/Other | Generic Matter Multi-Endpoint Switch | Switch | Matter | Generic Matter Multi-Endpoint Switch | |||
| Generic/Other | Generic Matter Outlet | Outlet / Plug | Matter | Generic Matter Outlet | |||
| Generic/Other | Generic Matter RGBW Light | Bulb | Matter | Generic Matter RGBW Light | |||
| Generic/Other | Generic Matter Switch | Switch | Matter | Generic Matter Switch | |||
| Generic/Other | Generic Z-Wave Acceleration Sensor | Acceleration Sensor | Z-Wave | Generic Z-Wave Acceleration Sensor | Show | ||
| Generic/Other | Generic Z-Wave Button Controller | Button Controller | Z-Wave | Generic Z-Wave Button Controller | Show | ||
| Generic/Other | Generic Z-Wave CentralScene Dimmer | Dimmer | Z-Wave | Generic Z-Wave CentralScene Dimmer | Show | ||
| Generic/Other | Generic Z-Wave CentralScene Switch | Switch | Z-Wave | Generic Z-Wave CentralScene Switch | Show | ||
| Generic/Other | Generic Z-Wave Contact Sensor | Contact Sensor | Z-Wave | Generic Z-Wave Contact Sensor | Show | ||
| Generic/Other | Generic Z-Wave Dimmer | Dimmer | Z-Wave | Generic Z-Wave Dimmer | Show | ||
| Generic/Other | Generic Z-Wave Garage Door Opener | Garage Door Controller | Z-Wave | Generic Z-Wave Garage Door Opener | Show | ||
| Generic/Other | Generic Z-Wave Lock | Lock | Z-Wave | Generic Z-Wave Lock | Show | ||
| Generic/Other | Generic Z-Wave Motion Sensor | Motion Sensor | Z-Wave | Generic Z-Wave Motion Sensor | Show | ||
| Generic/Other | Generic Z-Wave Motion/Temperature Sensor | Motion Sensor | Z-Wave | Generic Z-Wave Motion/Temperature Sensor | Show | ||
| Generic/Other | Generic Z-Wave Outlet | Outlet / Plug | Z-Wave | Generic Z-Wave Outlet | Show | ||
| Generic/Other | Generic Z-Wave Plus Button Controller | Button Controller | Z-Wave | Generic Z-Wave Plus Button Controller | Show | ||
| Generic/Other | Generic Z-Wave Plus Contact Sensor | Contact Sensor | Z-Wave | Generic Z-Wave Plus Contact Sensor | Show | ||
| Generic/Other | Generic Z-Wave Plus Dimmer | Dimmer | Z-Wave | Generic Z-Wave Plus Dimmer | Show | ||
| Generic/Other | Generic Z-Wave Plus Outlet | Outlet / Plug | Z-Wave | Generic Z-Wave Plus Outlet | Show | ||
| Generic/Other | Generic Z-Wave Plus Scene Dimmer | Dimmer | Z-Wave | Generic Z-Wave Plus Scene Dimmer | Show | ||
| Generic/Other | Generic Z-Wave Plus Scene Switch | Switch | Z-Wave | Generic Z-Wave Plus Scene Switch | Show | ||
| Generic/Other | Generic Z-Wave Plus Smoke/CO Detector | Smoke/CO Detector | Z-Wave | Generic Z-Wave Plus Smoke/CO Detector | Show | ||
| Generic/Other | Generic Z-Wave Plus Switch | Switch | Z-Wave | Generic Z-Wave Plus Switch | Show | ||
| Generic/Other | Generic Z-Wave Plus Thermostat | Thermostat | Z-Wave | Generic Z-Wave Plus Thermostat | Show | ||
| Generic/Other | Generic Z-Wave Relay | Relay | Z-Wave | Generic Z-Wave Relay | Show | ||
| Generic/Other | Generic Z-Wave Repeater | Repeater | Z-Wave | Generic Z-Wave Repeater | Show | ||
| Generic/Other | Generic Z-Wave RGBWW Controller | Bulb | Z-Wave | Generic Z-Wave RGBWW Controller | Show | ||
| Generic/Other | Generic Z-Wave Shade | Shade Controller | Z-Wave | Generic Z-Wave Shade | Show | ||
| Generic/Other | Generic Z-Wave Smart Dimmer | Dimmer | Z-Wave | Generic Z-Wave Smart Dimmer | Show | ||
| Generic/Other | Generic Z-Wave Smart Switch | Switch | Z-Wave | Generic Z-Wave Smart Switch | Show | ||
| Generic/Other | Generic Z-Wave Smoke Detector | Smoke/CO Detector | Z-Wave | Generic Z-Wave Smoke Detector | Show | ||
| Generic/Other | Generic Z-Wave Smoke/CO Detector | Smoke/CO Detector | Z-Wave | Generic Z-Wave Smoke/CO Detector | Show | ||
| Generic/Other | Generic Z-Wave Switch | Switch | Z-Wave | Generic Z-Wave Switch | Show | ||
| Generic/Other | Generic Z-Wave Temperature/Humidity Sensor | Temperature Sensor | Z-Wave | Generic Z-Wave Temperature/Humidity Sensor | Show | ||
| Generic/Other | Generic Z-Wave Thermostat | Thermostat | Z-Wave | Generic Z-Wave Thermostat | Show | ||
| Generic/Other | Generic Z-Wave Valve | Valve | Z-Wave | Generic Z-Wave Valve | Show | ||
| Generic/Other | Generic Z-Wave Water Sensor | Water Sensor | Z-Wave | Generic Z-Wave Water Sensor | Show | ||
| Generic/Other | Generic Zigbee Bulb | Bulb | Zigbee | Generic Zigbee Bulb | Show | ||
| Generic/Other | Generic Zigbee Contact Sensor | Contact Sensor | Zigbee | Generic Zigbee Contact Sensor | Show | ||
| Generic/Other | Generic Zigbee Contact Sensor (no temp) | Contact Sensor | Zigbee | Generic Zigbee Contact Sensor (no temp) | Show | ||
| Generic/Other | Generic Zigbee CT Bulb (dev) | Bulb | Zigbee | Generic Zigbee CT Bulb (dev) | Show | ||
| Generic/Other | Generic Zigbee Dimmer | Dimmer | Zigbee | Generic Zigbee Dimmer | Show | ||
| Generic/Other | Generic ZigBee Lock | Lock | Zigbee | Generic ZigBee Lock | Show | ||
| Generic/Other | Generic Zigbee Moisture Sensor | Water Sensor | Zigbee | Generic Zigbee Moisture Sensor | Show | ||
| Generic/Other | Generic Zigbee Motion Sensor | Motion Sensor | Zigbee | Generic Zigbee Motion Sensor | Show | ||
| Generic/Other | Generic Zigbee Motion Sensor (no temp) | Motion Sensor | Zigbee | Generic Zigbee Motion Sensor (no temp) | Show | ||
| Generic/Other | Generic Zigbee Motion/Humidity Sensor | Motion Sensor | Zigbee | Generic Zigbee Motion/Humidity Sensor | Show | ||
| Generic/Other | Generic Zigbee Multi-Endpoint Switch | Switch | Zigbee | Generic Zigbee Multi-Endpoint Switch | Show | ||
| Generic/Other | Generic Zigbee Outlet | Outlet / Plug | Zigbee | Generic Zigbee Outlet | Show | ||
| Generic/Other | Generic ZigBee RGB Light | Bulb | Zigbee | Generic ZigBee RGB Light | Show | ||
| Generic/Other | Generic ZigBee RGBW Light | Bulb | Zigbee | Generic ZigBee RGBW Light | Show | ||
| Generic/Other | Generic Zigbee Switch | Switch | Zigbee | Generic Zigbee Switch | Show | ||
| Generic/Other | Generic Zigbee Thermostat | Thermostat | Zigbee | Generic Zigbee Thermostat | Show |
End of the automatically generated list
2GIG 700 Series Smart Thermostat
Join instructions
1. Select the Start Z-Wave Inclusion button.
2. Touch any button to take the thermostat out of sleep mode.
3. Touch and hold MODE button for 5 seconds. SETUP will be displayed in the status display line.
4. Scroll to “Z-Wave” using ?? buttons. Touch FAN (Select).
5. When prompted by your Z-Wave controller, select YES in the Z-Wave Install screen.
6. Touch FAN (Select) to add thermostat to network.
7. The display line should flash WAIT and then SUCCESS if Z-Wave connection is made.
8. If Z-Wave does not connect to controller, WAIT, then FAIL will flash in status display line.
9. If thermostat fails to connect, repeat Steps three (3) through (7) to re-try connecting.
Your controller will indicate the thermostat was successfully added to its network (see your
controller’s user manual for details). Also, you can check if the thermostat was successfully added
to the network by checking the ZHID (Home ID) and ZNID (Node ID) located in the thermostat INFO
screen.
Exclude instructions
1. Select the Start Z-Wave Exclusion button.
2. Touch any button to take the thermostat out of sleep mode.
3. Touch and hold the MODE button for 5 seconds. SETUP will be displayed in the status display line.
5. Scroll to “Z-Wave” using ?? buttons. Touch FAN (Select).
6. When prompted by your Z-Wave controller, select YES in the Z-Wave exclude screen.
7. Touch FAN (Select) to remove thermostat to network.
8. The display line should flash WAIT then SUCCESS if the thermostat is removed from the network.
9. If the removal operation is not successful, WAIT will flash, then FAIL will flash in status display
line. Repeat Steps three (3) through (7) to re-try.
Factory reset instructions
1. Touch and hold MODE button to go to Setup menu.
2. Touch and hold MODE and the down arrow key to enter Advanced Menu.
3. Navigate to Restore Defaults to perform a factory reset.
ADT (Nortek) Water Leak Detector
Join instructions
- Select the Start Zigbee Pairing button.
- Pull the battery tab.
- The red LED will begin to blink slowly and then turn solid for 3 seconds.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Press the connect button and release when the LED blinks slowly.
- The LED will then turn on solid for 3 seconds indicating the detector is ready to connect.
AduroSmart ERIA Contact Sensor
Join instructions
- Select the Start Zigbee Pairing button.
- Use the provided pin to press and hold the reset button for 10 seconds.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Use the provided pin to press and hold the reset button for 10 seconds.
- Battery powered Zigbee devices often pair easier when their batteries are removed for 10 seconds following a factory reset.
AduroSmart ERIA Dimmer Switch
Join instructions
- Select the Start Zigbee Pairing button.
- Hold down the off (circle) button for 10 seconds until it flashes green 3 times.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Hold down the two middle buttons until the light flashes green. A red flash indicates an unsuccessful reset.
- Battery powered Zigbee devices often pair easier when their batteries are removed for 10 seconds following a factory reset.
AduroSmart ERIA Motion Sensor
Join instructions
- Select the Start Zigbee Pairing button.
- Use the provided pin to press and hold the reset button for 10 seconds.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Use the provided pin to press and hold the reset button for 10 seconds.
Aeotec (Aeon Labs) Aeotec Panic Button
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press the Learn button on your Panic Button with the pin or press the bottom- right action button. Your Panic Button’s green light will begin to pulse.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the Learn button on your Panic Button with the pin or press the bottom- right action button. Your Panic Button’s green light will begin to pulse.
Factory reset instructions
1. Press and hold the Learn button for 20 seconds with a pin.
Aeotec (Aeon Labs) aërQ Temperature & Humidity Sensor
Join instructions
1: Select the Start Z-Wave Inclusion button.
2: Insert the battery.
3: Press the button quickly three times in a row.
Exclude instructions
1: Select the Start Z-Wave Exclusion button.
2: Press the button quickly three times in a row.
Factory reset instructions
Keep the button pressed for 10 seconds. After 5 seconds the red LED will start blinking.
Aeotec (Aeon Labs) Contact Sensor
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press the security tamper switch located at the back of the Aeon Labs Door/Window Sensor to include it.
- The sensor will now stay awake for 10 minutes to receive network instructions. The LED on the sensor will be flashing while awake.
- Note: The DSB04100 sensor can only be taught to communicate to devices within its own network.
- If the Aeon Labs Door/Window Sensor was not included in a Z-Wave network, pressing the security switch will illuminate the LED solid red on the front of the sensor for 5 seconds.
- If the sensor was successfully included in the Z-Wave network, the LED will flash instead of staying solid.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Use an Aeon Z-Stick or Minimote to exclude the sensor from previous networks.
Factory reset instructions
- Use an Aeon Z-Stick or Minimote to return the sensor to a default state.
Aeotec (Aeon Labs) Door Window Sensor 6
Join instructions
- Select Start Z-Wave Inclusion button.
- Short press the product’s Action Button that you can find in the back of the product.
Exclude instructions
- Select Start Z-Wave Exclusion button.
- Short press the product’s Action Button that you can find in back of the product.
Factory reset instructions
Press the Action Button once that you can find in back of the product for 20 seconds and then release. This procedure should only be used when the primary controller is inoperable.
Aeotec (Aeon Labs) Door Window Sensor 7
Join instructions
- Select the Start Z-Wave Inclusion button.
- Remove the cover of your Door/Window Sensor 7.
- Tap the small black tamper switch 3 times quickly.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Remove the cover of your Door/Window Sensor 7.
- Tap the small black tamper switch 3 times quickly.
Factory reset instructions
- Remove the cover of your Door/Window Sensor 7.
- Press and hold the tamper switch for 5 seconds until the red LED blinks.
- Quickly release the tamper switch, and then immediately press and hold again.
- If successful, the LED will display a solid green LED.
Aeotec (Aeon Labs) Door/Window Sensor 7 Basic
Join instructions
- Select Start Z-Wave Inclusion button
- Open the housing.
- Remove the battery protection.
- Press the tamper on the side of the appliance three times quickly.
Exclude instructions
- Select Start Z-Wave Exclusion button
- Open the housing.
- Press the tamper on the side of the appliance three times quickly.
Factory reset instructions
Once Cover is removed and the tamper switch is tripped, push the tamper for 5 seconds until the RED LED
blinks once. Then release tamper and push it again for 5 seconds while the RED LED is blinking until the
GREEN LED blinks once.
Aeotec (Aeon Labs) Door/Window Sensor 7 Pro
Join instructions
- Select Start Z-Wave Inclusion button
- Open the housing.
- Remove the battery protection.
- Press the tamper on the side of the appliance three times quickly.
Exclude instructions
- Select Start Z-Wave Exclusion button
- Open the housing.
- Press the tamper on the side of the appliance three times quickly.
Factory reset instructions
Once Cover is removed and the tamper switch is tripped, push the tamper for 5 seconds until the RED LED
blinks once. Then release tamper and push it again for 5 seconds while the RED LED is blinking until the
GREEN LED blinks once.
Aeotec (Aeon Labs) Door/Window Sensor 7 Series
Join instructions
- Select Start Z-Wave Inclusion button
- Open the housing.
- Remove the battery protection.
- Press the tamper on the side of the appliance three times quickly.
Exclude instructions
- Select Start Z-Wave Exclusion button
- Open the housing.
- Press the tamper on the side of the appliance three times quickly.
Factory reset instructions
Once Cover is removed and the tamper switch is tripped, push the tamper for 5 seconds until the RED LED
blinks once. Then release tamper and push it again for 5 seconds while the RED LED is blinking until the
GREEN LED blinks once.
Aeotec (Aeon Labs) Door/Window Sensor Gen 2
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press the Action button 1 time to include it.
- Wait for the inclusion process to end and the device is successfully included.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the Action button 1 time to exclude it.
- Wait for the exclusion process to end and the device is successfully excluded.
Factory reset instructions
- Press and hold the Action button for 20 seconds and Status LED will be solid for 2 seconds to confirm a success.
Aeotec (Aeon Labs) Doorbell
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press the Action button on your Doorbell Gen5, and its LED will flash rapidly to indicate that it is communicating.
- If inclusion is successful, its LED will become solid for 2 seconds, then stop.
- If inclusion was unsuccessful, the LED will flash when you tap its button.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the Action button on your Doorbell.
- If exclusion is successful, its LED will begin to flash slowly.
Factory reset instructions
- Press and hold the Action button for 20 seconds and then release it.
- Your Doorbell will now be reset to its original settings, and the Network LED will be solid for 2 seconds and then start slow flashing as a confirmation.
Aeotec (Aeon Labs) Doorbell 6
Join instructions
- Power Doorbell 6 through the provided power adapter.
- Ensure that Doorbell 6 LED is flashing slowly.
- Select the Start Z-Wave Inclusion button.
- Tap the Doorbell 6 Action button once.
- If Doorbell 6 has successfully been included, the LED will be a solid color for 30 seconds, then turn off.
- If it fails inclusion the LED will flash slowly.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the Action button 6 times in 2 seconds.
- If your Doorbell 6 has been successfully excluded its LED will begin to flash slowly.
Factory reset instructions
- Press and hold the Action button for 20 seconds.
- Within 2-5 seconds, the test doorbell sound will run, then stop after 5 seconds has elapsed.
- From 5-10 seconds, the LED will begin to flash faster and faster still, from 10-20 seconds.
- After 21 seconds, the LED will quickly flash 3 times and then the LED will slowly pulse up and down as you hold down the Action button.
- With the LED pulsing, release the Action button, and the Doorbell 6 will be reset to factory defaults.
Aeotec (Aeon Labs) Dry Contact Sensor
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press the Action button on your Sensor.
- If inclusion is successful, its LED will become solid for 2 seconds, then disappear.
- If inclusion is unsuccessful, the LED will continue to flash if you tap its button.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the Action button on your Sensor.
- If your switch has been successfully excluded, its LED will begin to flash for a short time.
- If exclusion was not successful, the LED will return to its last state. Tap the button to confirm if it has been excluded, if excluded successfully, the LED will flash when tapped.
Factory reset instructions
- Press and hold the Action button for 20 seconds and Status LED will be solid for 2 seconds to confirm a success.
Aeotec (Aeon Labs) Dual Nano Switch
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press the Action button once on the Dual Nano Switch.
- If inclusion is successful, the green LED will be on for 2 seconds, and then return to a solid indication.
- If inclusion is unsuccessful, the red LED will be on for 2 seconds and then return to a colorful gradient.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the Action button on the Nano Switch once or toggle the external manual switch 3 times in fast succession.
- If the Nano Switch has been successfully excluded, its RGB LED will remain colorful gradient.
- If the exclusion was unsuccessful, the RGB LED will still be solid (following the state of the output load).
Factory reset instructions
- Press and hold the Action button for 20 seconds and then release it.
- Your Nano Switch will now be reset to its original settings, and the green LED will be solid for 2 seconds and then remain the colorful gradient status as a confirmation.
Aeotec (Aeon Labs) Garage Door Controller Gen 5
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press the Z-Wave button on the Garage Door Controller.
- The LED on the Garage Door Controller will flash rapidly, followed by a solid LED for 1-2 seconds for a successful inclusion.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the Z-Wave button on the Garage Door Controller.
- The LED on the Garage Door Controller will flash rapidly, followed by a solid LED for 1-2 seconds.
- The Network LED on the Garage Door Controller should now be flashing slowly to indicate successful exclusion.
Factory reset instructions
- Press and hold the Action button for 20 seconds and release.
- Your Garage Door Controller will now be reset to its original settings, and the Network LED will be solid for 2 seconds and then start slow flashing to confirm a success.
Aeotec (Aeon Labs) Home Energy Meter
Join instructions
- Remove the screw from the back of your Reader and open the battery cover.
- Select the Start Z-Wave Inclusion button.
- Press the Action button (small black button under the battery tray) on your reader.
- If your Reader has been successfully included, its light will remain solid for 1 second.
- If the inclusion was unsuccessful the light will flash after pressing your meter’s Action button.
Exclude instructions
- Remove the screw from the back of your Reader and open the battery cover.
- Select the Start Z-Wave Exclusion button.
- Press the Action button (small black button under the battery tray) on your reader.
- If your Reader has been successfully excluded, its light will flash for 1 second.
- If exclusion was unsuccessful the light will be solid after pressing your meter’s Action button.
Factory reset instructions
- Press and hold the Action button for 10 seconds.
- If successful, the LED on the HEM should begin to flash slowly.
Aeotec (Aeon Labs) Illumino Dimmer Switch
Join instructions
1. Select Start Z-Wave Inclusion button.
2. 1x tap the Top/ Bottom button of Dimmer Switch.
Exclude instructions
1. Select Start Z-Wave Exclusion button.
2. 3x tap the Top/ Bottom button of Dimmer Switch .
Factory reset instructions
Press and hold the Top/ Bottom button for 20 seconds.
Aeotec (Aeon Labs) Illumino Wall Switch
Join instructions
1. Select Start Z-Wave Inclusion button.
2. Press the Top/Buttom button once on product.
Exclude instructions
1. Select Start Z-Wave Exclusion button.
2. 3*tap the Top/Buttom button on product.
Factory reset instructions
Press and hold the Top/ Bottom button for 20s.
Aeotec (Aeon Labs) LED Bulb 5
Join instructions
- Select the Start Z-Wave Inclusion button.
- With the LED Bulb in its fitting, wait 2 seconds. Now toggle your wall switch on. The LED Bulb’s green LED will flash to indicate that it is looking for a Z-Wave network to connect to.
- After successful inclusion, the LED Bulb will illuminate.
- If inclusion has failed, it will remain without light.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Turn the LED Bulb’s wall switch on.
- Toggle the LED Bulb’s wall switch off, on, off, on, off, on within 2 seconds. The LED should flash orange, and if exclusion is successful, the orange LED will be solid for 2 seconds before becoming a white color.
- If exclusion is unsuccessful, the LED Bulb will flash orange for 3 seconds before changing to red for 2 seconds.
Factory reset instructions
- Factory reset is unavailable for this device. Instead, perform a general exclusion.
Aeotec (Aeon Labs) LED Bulb 6 Multi-Color
Join instructions
- Select the Start Z-Wave Inclusion button.
- With LED Bulb in its fitting, toggle your wall switch ON. LED Bulb’s LED will turn into a solid yellow color to indicate that it is in inclusion mode up to 10 seconds.
- After successful inclusion, LED Bulb will flash green -> white color for 3 seconds.
- If inclusion has failed, LED Bulb 6 Multi-Color will flash red -> white for 3 seconds.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Toggle LED Bulb’s wall switch 3 times (off > on, off > on, off > on) between 0.5 - 2 seconds per cycle.
- If LED Bulb 6 has been excluded successfully, the LED will flash blue > white for 3 seconds.
Factory reset instructions
- Turn LED Bulb’s wall switch on and wait 1 second.
- Toggle LED Bulb's wall switch 6 times (off -> on, off -> on, off -> on, off -> on, off -> on, off -> on) between 0.5 - 2 seconds per re-power.
- If successful, the LED Bulb 6 Multi-Color will change to a warm white, solid yellow, then flash red -> white 3 times to indicate a successful factory reset.
Aeotec (Aeon Labs) LED Bulb 6 Multi-White
Join instructions
- Select the Start Z-Wave Inclusion button.
- With the LED Bulb in its fitting, toggle your wall switch on. The LED Bulb’s LED will flash 2 times to indicate that it is looking for a Z-Wave network to connect to.
- After successful inclusion, the LED Bulb will flash off then on in about 0.5 seconds to indicate that it attempted to include in your network.
- If inclusion has failed, the LED Bulb 6 Multi-White will not react.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Turn the LED Bulb’s wall switch on and wait 1 second.
- Toggle the LED Bulb’s wall switch 3 times (off > on, off > on, off > on) between 0.5 - 2 seconds per cycle.
- The LED Bulb 6 will flash 1 time, dim to 5% for 5 seconds, then increase to 100% dim level to indicate a successful exclusion.
Factory reset instructions
- Turn the LED Bulb’s wall switch on and wait 1 second.
- Toggle the LED Bulb's wall switch 6 times (off -> on, off -> on, off -> on, off -> on, off -> on, off -> on) between 0.5 - 2 seconds per cycle.
- The LED Bulb 6 Multi-White will flash 2 times to indicate that it has successfully reset itself to factory defaults.
Aeotec (Aeon Labs) Micro Motor Controllers
Join instructions
Z-Stick:
- Connect Micro Motor Controller to an AC-input power source.
- Select the Start Z-Wave Inclusion button.
- Press the Action button on your Z-Stick.
- Press the Action button on your Micro Motor Controller.
- If the Micro Motor Controller has been successfully included, its Network LED will no longer flash.
- If inclusion was unsuccessful and the Network LED continues to flash repeat the above steps.
- Press the Action button on the Z-Stick to take it out of inclusion mode.
Minimote:
- Connect Micro Motor Controller to an AC-input power source.
- Select the Start Z-Wave Inclusion button.
- Press the Include button on your Minimote.
- Press the Action button on your Micro Motor Controller.
- If the Micro Motor Controller has been successfully included, its Network LED will no longer flash.
- If inclusion was unsuccessful and the Network LED continues to flash repeat the above steps.
- Press any button on your Minimote to take it out of inclusion mode.
Exclude instructions
Z-Stick:
- Select the Start Z-Wave Exclusion button.
- Press the Action button on your Z-Stick.
- Press the Action button on your Micro Motor Controller.
- If your Micro Motor Controller has been successfully excluded, its Network LED will flash.
- If the exclusion was unsuccessful, the Network LED will not flash.
- Press the Action button on the Z-Stick to take it out of exclusion mode.
Minimote:
- Select the Start Z-Wave Exclusion button.
- Press the Remove Button on your Minimote.
- Press the Action button on your Micro Motor Controller.
- If your Micro Motor Controller has been successfully excluded, its Network LED will flash.
- If exclusion was unsuccessful, the Network LED will not flash.
- Press any button on your Minimote to take it out of exclusion mode.
Factory reset instructions
- Use an Aeon Z-Stick or Minimote to return the controller to a default state.
Aeotec (Aeon Labs) Minimote
Join instructions
- Tap the inclusion "+" button, LED should be flashing blue.
- Tap the button on the device you want to add.
- After the LED stops flashing rapidly, tap any button to get out of inclusion mode.
Exclude instructions
- Tap the exclusion "-" button, LED should flash red.
- Tap button on the device you want to remove.
- After LED stops flashing rapidly, tap any button to get out of the exclusion mode.
Factory reset instructions
- Pull down the panel on the Minimote.
- Press and hold the bottom 2 buttons down. The red and blue LED will alternate faster and faster.
- When both red and blue LED's become solid, you may let go.
Aeotec (Aeon Labs) MultiSensor 6
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press the Action button on your MultiSensor 6. The LED on Multisensor 6 will flash green rapidly, followed by a solid green LED for 1 second for a successful inclusion, or a solid red LED for 1 second for a failed inclusion.
- You can test if your MultiSensor 6 has been successfully included by pressing its Action button. If you press the button and your sensor's green LED is solid for a few seconds, then inclusion has been successful.
- If the green LED flashes when the button is pressed, the inclusion has been unsuccessful and you should repeat the steps from step 1.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the Action button on your MultiSensor 6. The LED on MultiSensor 6 will flash red then change into a colorful gradient.
- If your MultiSensor 6 has been successfully excluded, the RGB LED will be active with a colorful gradient for 3 seconds. When you press the Action button on MultiSensor 6, its green LED will flash.
- If exclusion was unsuccessful, the green LED will stay solid for a few seconds when you press the Action button.
Factory reset instructions
- Factory reset is unavailable for this device. Instead, perform a general exclusion.
Aeotec (Aeon Labs) MultiSensor 7
Join instructions
- Select Start Z-Wave Inclusion
- Press once the Action Button on the product.
Exclude instructions
- Select Start Z-Wave Exclusion
- Press once the Action Button on the product.
Factory reset instructions
Press and hold the Action Button on product for 15-20s.
Aeotec (Aeon Labs) MultiSensor 7
Join instructions
1. Select Start Z-Wave Inclusion button.
2. Press once the Action Button on the product.
Exclude instructions
1. Select Start Z-Wave Exclusion button.
2. Press once the Action Button on the product.
Factory reset instructions
Press and hold the Action Button on product for 15-20s.
Aeotec (Aeon Labs) MultiSensor Gen5
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press the Z-Wave Button on your MultiSensor Gen5.
- You can test if your MultiSensor Gen5 has been successfully included by pressing its Z-Wave button. If you press the button and your sensor’s LED illuminates for a few seconds, then inclusion has been successful.
- If the LED flashes when the button is pressed, the inclusion has been unsuccessful and you should repeat the above steps.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the Z-Wave Button on your MultiSensor Gen5.
- If your MultiSensor Gen5 has been successfully excluded, its LED will flash when you press the Z-Wave button.
- If exclusion was unsuccessful, the LED will stay solid for a few seconds when you press the Z-Wave button.
Factory reset instructions
- Press and hold MultiSensor Gen5 Action button (For 20 seconds).
- The LED of the MultiSensor Gen5 will flash faster and faster. At 20 seconds, the LED should become solid for 1-2 seconds to confirm factory reset.
- Release the MultiSensor Gen5 Action button.
Aeotec (Aeon Labs) Nano Dimmer
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press the Action button on the Nano Dimmer, the green LED (basic secure indication) will flash to indicate the Nano Dimmer is entering into inclusion mode.
- If the Nano Dimmer has been successfully included, its RGB LED will be solid.
- If inclusion was unsuccessful, the red LED will be on for 2 seconds and then remain a colorful gradient, repeat the steps above.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the Action button on the Nano Dimmer 1 time or toggle the external manual switch 3 times in fast succession.
- If the Nano Dimmer has been successfully excluded, its RGB LED will remain a colorful gradient.
- If exclusion was unsuccessful, the RGB LED will still be solid (following the state of the output load).
Factory reset instructions
- Press and hold the Action button for 20 seconds and then release it.
- Your Nano Switch will now be reset to its original settings, and the green LED will be solid for 2 seconds and then remain the colorful gradient status as a confirmation.
Aeotec (Aeon Labs) Nano Shutter
Join instructions
- Select Start Z-Wave Inclusion button.
- Short press the product’s Action button that you can find on the product's housing.
If the Nano Dimmer has been successfully added to your Z-Wave network, its RGB LED will be solid. If unsuccessful, the red LED will be on for 2 seconds and then remain a colorful gradient, repeat the instructions above from step 1.
Exclude instructions
- Select Start Z-Wave Exclusion button.
- Quick press the product’s Action button 6 times that you can find on the product's housing or toggle the external manual switch 2 times in fast succession.
If the Nano Dimmer has been successfully removed from your Z-Wave network, its RGB LED will remain colorful gradient. If the removal was unsuccessful, the RGB LED will still be solid (following the state of the output load), repeat the instructions above from step 1.
Factory reset instructions
Press and hold the Action button that you can find on the product's housing for 20 seconds and then release. This procedure should only be used when the primary controller is inoperable.
Aeotec (Aeon Labs) Nano Switch
Join instructions
- Select the Start Z-Wave Inclusion button.
- short press the product’s Action button that you can find on the product's housing.
Exclude instructions
- Select the Start Z-Wave Exclusion button
- short press the product’s Action button that you can find on the product's housing.
Factory reset instructions
Press and hold the Action button that you can find on the product's housing for 20 seconds and then release. This procedure should only be used when the primary controller is inoperable.
Aeotec (Aeon Labs) Nano Switch
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press the Action button once on the Nano Switch.
- If inclusion is successful, the green LED will be on for 2 seconds, and then return to a solid indication.
- If inclusion is unsuccessful, the red LED will be on for 2 seconds and then return to a colorful gradient.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the Action button on the Nano Switch once or toggle the external manual switch 3 times in fast succession.
- If the Nano Switch has been successfully excluded, its RGB LED will remain colorful gradient.
- If the exclusion was unsuccessful, the RGB LED will still be solid (following the state of the output load).
Factory reset instructions
- Press and hold the Action button for 20 seconds and then release it.
- Your Nano Switch will now be reset to its original settings, and the green LED will be solid for 2 seconds and then remain the colorful gradient status as a confirmation.
Aeotec (Aeon Labs) NanoMote One
Join instructions
- Select the Start Z-Wave Inclusion button.
- Double click the NanoMote button, the LED will flash rapidly with a white color.
- If your NanoMote has been successfully included, its white LED will be solid for about 10 seconds, then flash green to indicate it is awake.
- If the inclusion was unsuccessful, the red LED will be solid for 2 seconds and then off, repeat the above steps.
- If your NanoMote does not go to sleep on its own, press and hold for 2 seconds (or until LED turns orange) then release its button to put your NanoMote to sleep.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Double click the NanoMote button, the LED will become a solid green color.
- If your NanoMote has been excluded from your Z-Wave network, its LED will begin cycling through a rainbow of colors.
Factory reset instructions
- Press and hold the NanoMote button for 20 seconds.
- The LED will change from: orange > green > red > pink > red
- Release the button on the second red LED status. It will remain red for 2 seconds
- Tap button again while second red LED is illuminated (you'll have 2 seconds to do so).
Aeotec (Aeon Labs) NanoMote Quad
Join instructions
- Select the Start Z-Wave Inclusion button.
- Double click the NanoMote button, the LED will flash rapidly with a white color.
- If your NanoMote has been successfully included, its white LED will be solid for about 10 seconds, then flash green to indicate it is awake.
- If inclusion was unsuccessful, the red LED will be solid for 2 seconds and then off, repeat the above steps.
- If your NanoMote does not go to sleep on its own, press and hold for 2 seconds (or until LED turns orange) then release its button to put your NanoMote to sleep.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Double click the NanoMote button, the LED will become a solid green color.
- If your NanoMote has been excluded, its LED will begin cycling through a rainbow of colors.
Factory reset instructions
- Press and hold the NanoMote button for 20 seconds.
- The LED will change from: orange > green > red > pink > red.
- Release the button on the second red LED status. It will remain red for 2 seconds.
- Tap button again while second red LED is illuminated (you'll have 2 seconds to do so).
Aeotec (Aeon Labs) Range Extender 6
Join instructions
Z-Stick:
- Select the Start Z-Wave Inclusion button.
- Press the Action button on your Z-Stick.
- If Range Extender has been successfully included, its Network LED will no longer flash.
- If inclusion was unsuccessful and the Network LED continues to flash, repeat the above steps.
- Press the Action button on the Z-Stick to take it out of inclusion mode.
Minimote:
- Select the Start Z-Wave Inclusion button.
- Press the Include button on your Minimote.
- If the Range Extender has been successfully included, its Network LED will no longer flash.
- If inclusion was unsuccessful and the Network LED continues to flash, repeat the above steps.
- Press any button on your Minimote to take it out of inclusion mode.
Exclude instructions
Z-Stick:
- Select the Start Z-Wave Exclusion button.
- Press the Action button on your Z-Stick.
- If your Range Extender has been successfully excluded, its Network LED will flash.
- If exclusion was unsuccessful, the Network LED will not flash.
- Press the Action button on the Z-Stick to take it out of exclusion mode.
Minimote:
- Select the Start Z-Wave Exclusion button.
- Press the Remove button on your Minimote.
- If your Range Extender has been successfully excluded, its Network LED will flash.
- If exclusion was unsuccessful, the Network LED will not flash.
- Press any button on your Minimote to take it out of exclusion mode.
Factory reset instructions
- Use an Aeon Z-Stick or Minimote to return the Range Extender to a default state.
Aeotec (Aeon Labs) Range Extender 7
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press the Z-Wave button on your Range Extender 7 and quickly release the button (should only be a quick tap of the Action button).
- The Range Extender 7 will quickly flash its white LED up to 30 seconds, or until it is included successfully.
- If successfully included, the LED light will become brighter. If inclusion fails, the LED will return to slow pulsing.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the button on your Range Extender 7.
- If Range Extender has been successfully excluded from your network, its LED will be slowly pulsing.
Factory reset instructions
- Press and hold the Z-Wave button for 20 seconds to completely factory reset your Range Extender 7.
- During the time that you are holding your Range Extender 7 Action button down, the LED will cycle through these stages: OFF (at 1 second) > Pulsing (at 2 seconds) > Flash (at 5 seconds) > Fast Flashing (at 10 seconds) > Solid for 2 seconds then pulsing (at 20 seconds) indicating factory reset complete.
- You may let go of the button. Your Range Extender has now be reset to its original settings, and the LED will continuously pulse until added again.
Aeotec (Aeon Labs) Recessed Door Sensor 7
Join instructions
1. Press the sensor latch with a slotting screwdriver to remove the lid of the sensor.
2. Squeeze the sides of the sensor casing to alleviate pressure on the chipboard; slide the chipboard out.
3. Remove the Pull Tab to engage the pre-installed battery. The sensor’s LED will fade the color red in and out for a few seconds to indicate that it’s powered on.
4. To add the product to your automation network manually:
(a) Select Start Z-Wave Inclusion button.
(b) Single-click the Action Button; its red LED will flash for a few seconds.
(c) If you want to add the product into S2 Authenticated network, please enter the PIN code (the underlined 5-digits of the DSK) when prompted. [IMPORTANT] QR/PIN can be found at the bottom of the product. A full DSK string can be found when you open the packaging on the Aeotec Logo Side. Please cut it out of the packaging and write some memo on its backside. Keep it in a safe place.
(d) Wait for the adding process to end.
(e) Confirm the adding result. Successful adding can be confirmed by your controller’s message or the LED status. If adding is successful, LED will become solid red color for 10 minutes and then off, or goes into sleep immediately if receiving the Wake Up No More Information from the controller. If its LED goes back to slow fade-in fade-out red color for 10 seconds, it indicates adding is unsuccessful. The product will auto-reset and then activate SmartStart. Repeat the above steps or contact us for further support if needed.
6. Squeeze the sides of the sensor casing lightly again and re-insert the chipboard as it was. Re-attach the lid.
7. Recessed Door Sensor 7 is now a part of your Z-Wave home control system. You can configure it and its automations via your Z-Wave system; please refer to your software's user guide for precise instructions.
Exclude instructions
1. Select Start Z-Wave Exclusion button.
2. Make sure the product is powered.
3. Single-click the Action Button; its red LED will flash for a few seconds.
4. Confirm the removing result. Successful removing can be confirmed by your controller’s message or the LED status. If the removing is successful, LED will change to the default unpaired state which is slow fade-in fade-out red color. If its LED extinguish without slow fade-in fade-out red color, it indicates the removing is unsuccessful. Repeat the above steps or contact us for further support if needed.
Factory reset instructions
1. Make sure the product is powered.
2. Press and hold the Action Button for at least 20s, and release when LED becomes solid red color, then Factory Reset is performed.
3. Wait for the LED indicator to be slow fade-in fade-out red LED color, which indicates the reset operation is successful. Otherwise, please try again. Contact us for further support if needed.
Aeotec (Aeon Labs) Recessed Door Sensor Gen 5
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press the Action button on your sensor. If your sensor has been successfully included, its LED will become solid for 2 seconds then disappear.
- If inclusion was unsuccessful, the LED will continue to flash if you tap its button.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the Action button on your sensor. If your sensor has been successfully excluded, its LED will begin to flash for a short time.
- If exclusion was unsuccessful, the LED will return to its last state. Tap the button to confirm if it has been excluded, if excluded successfully, the LED will flash when tapped.
Factory reset instructions
- Press and hold the Action button for 20 seconds and then release it. Your sensor will now be reset to its original settings.
Aeotec (Aeon Labs) Siren
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press the Action button on your siren and its LED will flash rapidly to indicate that it is communicating.
- If your siren has been successfully included, its LED will become solid for 2 seconds and then stop.
- If inclusion was unsuccessful, the LED will flash when you tap its button.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the Action button on your siren.
- If your siren has been successfully excluded, its LED will begin to flash.
Factory reset instructions
- Press and hold the Action button for 20 seconds.
- At 8 seconds, the siren will sound for 1 second and then stop.
- The LED will continue to flash faster and faster and will then turn solid for 2 seconds to indicate a successful factory reset.
- You may let go of the Action button, and the siren factory reset is then complete.
Aeotec (Aeon Labs) Siren 6
Join instructions
- Power Siren 6 through the provided power adapter.
- Ensure that Siren 6 LED is flashing slowly.
- Select the Start Z-Wave Inclusion button.
- Quickly tap the Siren 6 Action button once.
- If Siren 6 has been successfully included, the LED will emit a solid color for 30 seconds, then turn off.
- If the Siren 6 failed inclusion, the LED will continue to flash slowly.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the Action button 6 times within 2 seconds.
- If your Siren 6 has been successfully excluded its LED will begin to flash slowly.
Factory reset instructions
- Press and hold the Action button for 20 seconds.
- Within 2-5 seconds, the test siren sound will run, then stop after 5 seconds has elapsed.
- From 5-10 seconds, the LED will begin to flash faster and faster still, from 10-20 seconds.
- After 21 seconds, the LED will quickly flash 3 times and then the LED will slowly pulse up and down as you hold down the Action button.
- With the LED pulsing, release the Action button, and the Siren 6 will be reset to factory defaults.
Aeotec (Aeon Labs) Smart Energy Switch
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press the button on the device to include it.
- Wait for the inclusion process to end and the device is successfully included.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Use an Aeon Z-Stick or Minimote to exclude the switch. If the Smart Energy Switch was successfully excluded, the LED will be flashing.
- If it was not successfully excluded, the LED will either be solid ON or OFF (depending on if the switch is on or off).
Factory reset instructions
- Factory reset is unavailable for this device. Instead, perform a general exclusion.
Aeotec (Aeon Labs) Smart Switch 6
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press the Action button on your switch 1 time and the LED will flash a green LED.
- If your switch has been successfully included, its LED will become solid green for 2 seconds.
- If inclusion was unsuccessful, the LED will return to a rainbow gradient.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the Action button on your switch.
- If your switch has been successfully excluded, its LED will become a rainbow gradient.
- If exclusion was unsuccessful, the LED will become green or purple depending on how your LED mode is set.
Factory reset instructions
- Press and hold the Action button for 20 seconds.
- The LED will change between these colors: yellow > purple > red (flashes faster and faster).
- When the LED changes to a green state, you may let go of the Action button.
- When the LED changes to a rainbow state, it has been successfully reset.
Aeotec (Aeon Labs) Smart Switch 7 US
Join instructions
- Select Start Z-Wave Inclusion button.
- Short press the Action Button on the product one time.
Exclude instructions
- Select Start Z-Wave Exclusion button.
- Short press the Action Button on the product 2 times.
Factory reset instructions
Press and hold the Action Button for 15-20s.
Aeotec (Aeon Labs) TriSensor
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press the Action button on your sensor once.
- The LED will turn yellow for 10 seconds.
- If the LED flashes green 2 times, then the sensor has successfully been included.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the Action button on your sensor.
- The LED will turn purple for 2 seconds, and then white when exclusion is successful.
Factory reset instructions
- Press and hold the Action button for 15 seconds.
- The red LED flashes to confirm a successful factory reset.
Aeotec (Aeon Labs) WallMote 7
Join instructions
1. Select Start Z-Wave Inclusion button.
2. Tap once the top/ bottom button, then the device will enter pairing mode.
Exclude instructions
1. Select Start Z-Wave Exclusion button.
2. Tap 6 times the top/ bottom button, then the device will enter unpairing mode.
Factory reset instructions
Press and hold the top/buttom button for 20s
Aeotec (Aeon Labs) WallMote Quad
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press the Action button once on the WallMote Quad to include it.
- The green LED will be on for 2 seconds and then the orange LED will fast flash for 10 minutes (if the WallMote Quad does not receive the Wake Up No More Info command from primary Controller) to indicate the inclusion is successful.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the Action button on your WallMote Quad.
- If your WallMote Quad is successfully excluded, the LED will become a colorful gradient for a few seconds and then turn off.
- If the exclusion was unsuccessful, the red LED will be solid for 2 seconds and then turn off, repeat the above steps.
Factory reset instructions
- Press and hold the Action button for 20 seconds.
- The LED should flash between green, purple, then red which will flash rapidly until a green LED becomes solid for 2 seconds to indicate a successful factory reset.
- Let go of the Action button.
Aeotec (Aeon Labs) WallMote Quad
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press the Action button once on the WallMote Quad to include it.
- The green LED will be on for 2 seconds and then the orange LED will fast flash for 10 minutes (if the WallMote Quad does not receive the Wake Up No More Info command from primary Controller) to indicate the inclusion is successful.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the Action button on your WallMote Quad.
- If your WallMote Quad is successfully excluded, the LED will become a colorful gradient for a few seconds and then turn off.
- If exclusion was unsuccessful, the red LED will be solid for 2 seconds and then turn off, repeat the above steps.
Factory reset instructions
- Press and hold the Action button for 20 seconds.
- The LED should flash between green, purple, then red which will flash rapidly until a green LED becomes solid for 2 seconds to indicate a successful factory reset.
- Let go of the Action button.
Aeotec (Aeon Labs) Water Sensor 7 Pro
Join instructions
- Select Start Z-Wave Inclusion button
- Open the housing.
- Remove the battery protection.
- Press the tamper on the side of the appliance three times quickly.
Exclude instructions
- Select Start Z-Wave Exclusion button
- Open the housing.
- Press the tamper on the side of the appliance three times quickly.
Factory reset instructions
Once Cover is removed and the tamper switch is tripped, push the tamper for 5 seconds until the RED LED
blinks once. Then release tamper and push it again for 5 seconds while the RED LED is blinking until the
GREEN LED blinks once.
AGSHome Motion Sensor
Join instructions
- Select the Start Zigbee Pairing button.
- Remove the battery tab.
- The status indicator LED starts blinking to indicate pairing mode is active. If not, press and hold the button for 5 seconds to manually enter the pairing mode.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Press and hold the button for 5 seconds.
Alfred Z-Wave Lock
Join instructions
- Select Start Z-Wave Inclusion button
- Enter master mode(refer to programming instruction)
- Input “8” to enter “function extension settings”
- Input “1” to join a network.
Exclude instructions
- Select Start Z-Wave Exclusion button.
- Enter master mode(refer to programming instruction)
- Input “8” to enter “function extension settings”
- Input “2” to log off a network.
Factory reset instructions
1.Open the door and keep the lock in ""unlock"" status
2.Open battery box and find the reset button.
3.Use a sharp thing to press and hold the reset button.
4.Keep holding the reset button and remove a battery from battery box then replace it.
5.Keep holding the reset button until hearing voice guide.
Amazon Echo
Join instructions
Click Install Integration App above to begin a guided integration process.
August August Pro Lock
Join instructions
- Open the August app
- Go to the Lock Settings screen
- Select Z-Wave Settings
- Select Add To A Z-Wave Network
- Select Start Z-Wave Inclusion button
- Select My Hub is in Inclusion Mode on the August app
Exclude instructions
- Open the August app
- Go to the Lock Settings screen
- Select Z-Wave Settings
- Select Remove Z-Wave Device
- Select Start Z-Wave Exclusion
- Select My Hub is in Exlusion Mode on the August app
Factory reset instructions
1. Open the August app
2. Go to the Lock Settings screen
3. Select Z-Wave Settings
4. Select Remove Z-Wave device
5. Select My Hub Is No Longer Working
6. Caution: Resetting a Z-Wave device without telling the hub can cause performance issues. Use this procedure only when the Z-Wave hub is missing or otherwise inoperable.
7. Select Reset Z-Wave Device
8. On the Reset Z-Wave Device? prompt select Reset
Aurora AOne Smart Double Socket
Join instructions
- On initial power up, the device will automatically enter pairing mode for 3 minutes.
- Pairing is indicated by the LED light around the button flashing Blue quickly.
- Select the Start Zigbee Pairing button.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Press and hold the pairing button for 6 seconds before releasing.
- Cycle mains power to the outlet.
Aurora AOne Smart Plug-In Socket
Join instructions
- Select the Start Zigbee Pairing button.
- Press and hold the pairing button for 6 seconds before releasing. The light on the device will begin flashing.
- The light on the smart socket will stop flashing when pairing is successful.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Plug in the socket.
- Press and hold the pairing button for 6 seconds before releasing.
Aurora AOne Smart Remote
Join instructions
- Remove the battery cover.
- Select the Start Zigbee Pairing button.
- Press and hold the pairing button for 3 seconds before releasing. The light on the front of the remote will flash periodically to confirm it is searching for the hub.
- The light on the remote will remain solid for 10 seconds to confirm pairing was successful.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Remove the battery cover.
- Press and hold the pairing button for 3 seconds before releasing.
Aurora RGBW GLS
Join instructions
- Turn off power before fitting bulb.
- Select the Start Zigbee Pairing button.
- Turn on power, bulb will flash twice indicating that it's in pairing mode.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Switch bulb on and off 6 times.
Aurora RGBW GU10
Join instructions
- Turn off power before fitting bulb.
- Select the Start Zigbee Pairing button.
- Turn on power, bulb will flash twice indicating that it's in pairing mode.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Switch bulb on and off 6 times.
Aurora Smart dimmable GLS Lamp
Join instructions
- Turn off power before fitting bulb.
- Select the Start Zigbee Pairing button.
- Turn on power, bulb will flash twice indicating that it's in pairing mode.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Switch bulb on and off 6 times.
Aurora Smart Door / Window sensor
Join instructions
- Select the Start Zigbee Pairing button.
- Insert the batteries in the sensor.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Hold the button down until the LED flashes continuously, then release the button.
- After releasing the button the sensor should flash once indicating the reset is complete.
Aurora Smart PIR Sensor
Join instructions
- Select the Start Zigbee Pairing button.
- Insert the batteries in the sensor.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Hold the button down until the LED flashes continuously, then release the button.
- After releasing the button the sensor should flash once indicating the reset is complete.
Aurora Smart Tunable GLS
Join instructions
- Turn off power before fitting bulb.
- Select the Start Zigbee Pairing button.
- Turn on power, bulb will flash twice indicating that it's in pairing mode.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Switch bulb on and off 6 times.
Aurora Smart Tunable GU10
Join instructions
- Turn off power before fitting bulb.
- Select the Start Zigbee Pairing button.
- Turn on power, bulb will flash twice indicating that it's in pairing mode.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Switch bulb on and off 6 times.?
Aurora Zigbee vintage G125 Lamp
Join instructions
- Turn off power before fitting bulb.
- Select the Start Zigbee Pairing button.
- Turn on power, bulb will flash twice indicating that it's in pairing mode.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Switch bulb on and off 6 times.
Aurora Zigbee vintage GLS Lamp
Join instructions
- Turn off power before fitting bulb.
- Select the Start Zigbee Pairing button.
- Turn on power, bulb will flash twice indicating that it's in pairing mode.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Switch bulb on and off 6 times.
Aurora Zigbee vintage ST64 Lamp
Join instructions
- Turn off power before fitting bulb.
- Select the Start Zigbee Pairing button.
- Turn on power, bulb will flash twice indicating that it's in pairing mode.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Switch bulb on and off 6 times.
Axis Labs Gear
Join instructions
- Select the Start Zigbee Pairing button.
- Immediately press the Pair button on the device.
- The touch strip should flash green twice to indicate a successful pairing.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Make sure the device is powered on.
- Press and hold the 'SET', 'PAIR', and 'GROUP' buttons at the top of the device for several seconds until the LEDs start flashing.
- The device will then automatically reset after a few short seconds.
BeSense 360 Ceiling Sensor
Join instructions
- Select the Start Z-Wave Inclusion button.
- Activate the inclusion mode at the sensor by pressing the tamper switch 3 times.
- Wait about 15-30 seconds for the inclusion process to finish.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the tamper switch 3 times.
- Wait about 15-30 seconds for the exclusion process to finish.
Factory reset instructions
- Press the tamper switch 6 times to restore factory settings.
BeSense Door/Window Sensor
Join instructions
- Select the Start Z-Wave Inclusion button.
- Activate the inclusion mode at the sensor by pressing the tamper switch 3 times.
- Wait about 15-30 seconds for the inclusion process to finish.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the tamper switch 3 times.
- Wait about 15-30 seconds for the exclusion process to finish.
Factory reset instructions
- Press the tamper switch 6 times to restore factory settings.
BeSense PIR Wall Sensor
Join instructions
- Select the Start Z-Wave Inclusion button.
- Activate the inclusion mode at the sensor by pressing the tamper switch 3 times.
- Wait about 15-30 seconds for the inclusion process to finish.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the tamper switch 3 times.
- Wait about 15-30 seconds for the exclusion process to finish.
Factory reset instructions
- Press the tamper switch 6 times to restore factory settings.
Bond Home Bond Bridge
Join instructions
- Use the Bond Home smartphone app to set up the bridge on the local network.
- Test the device functionality using the smartphone app.
- Click the Install App button below to install the Bond Integration.
- Add device in Bond Integration App, if it is not shown immediately hit refresh.
Bosch PIR Motion Detector
Join instructions
- Unlock the battery cover and slide it upwards to remove.
- Select the Start Zigbee Pairing button.
- Remove both batteries for at least 10 seconds.
- Reinsert both batteries. The LED on the front of the sensor will be solid for 2 seconds.
- The LED will begin to flash On > Off > On > Off > On > Off (for 5 seconds) and will continue to flash in this cycle for up to 3 minutes.
- If the motion sensor does not pair with the hub in less than 3 minutes, perform a factory reset and repeat the above steps to join the Zigbee network.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Unlock the battery cover and slide it upwards to remove.
- Press upward on the tamper switch located in-between the batteries, keeping it engaged while you remove both batteries.
- Wait at least 4 seconds, but do not release the tamper switch.
- Keep the tamper switch engaged while you reinsert both batteries.
- Release the tamper switch. The device is now reset to factory default settings.
Bosch TriTech Motion Detector
Join instructions
- Unlock the battery cover and slide it upwards to remove.
- Select the Start Zigbee Pairing button.
- Remove both batteries for at least 10 seconds.
- Reinsert both batteries. The LED on the front of the sensor will be solid for 2 seconds.
- The LED will begin to flash On > Off > On > Off > On > Off (for 5 seconds) and will continue to flash in this cycle for up to 3 minutes.
- If the motion sensor does not pair with the hub in less than 3 minutes, perform a factory reset and repeat the above steps to join the Zigbee network.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Unlock the battery cover and slide it upwards to remove.
- Press upward on the tamper switch located in-between the batteries, keeping it engaged while you remove both batteries.
- Wait at least 4 seconds, but do not release the tamper switch.
- Keep the tamper switch engaged while you reinsert both batteries.
- Release the tamper switch. The device is now reset to factory default settings.
CEL Cotet Z10 Range Extender
Join instructions
- Select the Start Zigbee Pairing button.
- Press and hold the button for 2 seconds.
- The red LED will begin to blink slowly and then turn solid for 3 seconds.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Unplug the device.
- Hold the button while plugging the device back in.
- Continue to hold the button until the LED turns solid orange and then release the button.
Centralite Contact Sensor
Join instructions
- Select the Start Zigbee Pairing button.
- Slide the sensor off the mount and remove cover. Remove battery for 10 seconds and replace
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Slide the sensor off the mount, remove cover, and remove battery.
- While holding down the reset button, reinsert battery to factory reset the device.
Centralite Keypad
Join instructions
- Select the Start Zigbee Pairing button.
- Remove the battery. Wait 10 seconds then re-insert battery.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Remove the battery and wait 10 seconds.
- Press and hold the tamper switch while inserting one battery. Hold tamper switch for 2 seconds after the battery is installed. The tamper switch is the little flat plastic tab located on the back where the mounting bracket connects to the device, it is above the battery compartment.
- Note: The factory reset process puts the security keypad back into pairing mode.
- Upon a proper reset the top right icon will be flashing green on your keypad.
- You may now insert the 2nd battery.
Centralite Micro Door Sensor
Join instructions
- Select the Start Zigbee Pairing button.
- Slide the sensor off the mount and remove cover. Remove battery for 10 seconds and replace
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Slide the sensor off the mount, remove cover, and remove battery.
- While holding down the reset button, reinsert battery to factory reset the device.
Centralite Motion Sensor
Join instructions
- Select the Start Zigbee Pairing button.
- Slide the sensor off the mount and remove cover. Remove battery for 10 seconds and replace
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Slide the sensor off the mount, remove cover, and remove battery.
- While holding down the reset button, reinsert battery to factory reset the device.
Centralite Nightlight/Repeater
Join instructions
- Select the Start Zigbee Pairing button.
- Plug in the device, the LED should be blue and then start blinking.
- Once joined the LED will blink red, green and blue.
- Press the button to turn off the blinking.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Unplug the device.
- Hold the button while plugging the device back in.
- Continue to hold the button until the LED turns solid orange and then release the button.
Centralite Pearl Thermostat
Join instructions
- Select the Start Zigbee Pairing button.
- Enter Programming Mode, navigate to Menu ID “17”, press HOLD, then navigate to option “11”, then press HOLD again.
- The device will then factory reset itself and begin looking for an open network to join.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Enter Programming Mode, navigate to Menu ID “17”, press HOLD, then navigate to option “11”, then press HOLD again.
- The device will then factory reset itself and begin looking for an open network to join.
Centralite Smart Outlet
Join instructions
- Select the Start Zigbee Pairing button.
- Hold the on/off button while plugging it into the wall and continue to hold the button until the status LED turns on.
- After the Smart Outlet has successfully joined a Zigbee network, the status LED will turn solid green.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Unplug any devices from the module and unplug from the wall.
- Hold the on/off button while plugging it back into the wall and continue to hold the button until the status LED turns on.
Cree Connected A-19 Bulb
Join instructions
Preferred Method:
- Select the Start Zigbee Pairing button.
- Turn ON the bulb > pause 2 seconds > turn OFF the bulb > pause 2 seconds > Turn ON the bulb > pause 2 seconds > turn OFF the bulb > pause 2 seconds > Turn ON the bulb > pause 2 seconds > turn OFF the bulb > pause 2 seconds > Turn ON the bulb
- The bulb will flash once, indicating it is reset and ready for pairing.
Alternate Method:
- Select the Start Zigbee Pairing button.
- See Factory Reset (Alternate Method) to reset the bulb and put it into pairing mode.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
Preferred Method:
- Turn ON the bulb > pause 1 seconds > turn OFF the bulb > pause 2 seconds > Turn ON the bulb > pause 1 seconds > turn OFF the bulb > pause 2 seconds > Turn ON the bulb > pause 1 seconds > turn OFF the bulb > pause 2 seconds > Turn ON the bulb.
- The bulb will flash once, indicating it is reset and ready for pairing.
Alternate Method 1 - Use a Philips Hue Dimmer Switch:
- Turn the bulb on (ensure there are no others in the same lamp, as they could be reset too, using this method).
- Hold the remote within 4 inches of the bulb.
- Press and hold the 1st (On / I in some countries) and the 4th (Off / O in some countries) buttons simultaneously for about 10 seconds, until the bulb starts flashing on and off.
- If the bulb stopped flashing (it will normally turn fully on again after reset) and the green LED on the remote (top left of the remote) flashed green - your bulb is reset.
- This method can be used for nearly ALL Zigbee LL bulbs.
Alternate Method 2 - Use a Lutron LZL-4B Connected Bulb Remote (Discontinued Product):
- Hold the remote within 4 inches of the bulb.
- Press and hold the 2nd (up arrow) and 4th (light off) buttons simultaneously.
- The bulb should flash on and off.
- The green LED on the remote should come on and may flash a few times.
- Continue to hold both buttons on the remote until the green LED goes off completely.
- This method can be used for nearly ALL Zigbee LL bulbs.
Current E-Wand
Join instructions
- Select the Start Zigbee Pairing button.
- Press and release the programming button three times.
- The device should start beeping to indicate it is in pairing mode.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Press and hold the PROGRAMMING BUTTON until you hear a QUINTUPLE BEEP (5), then release.
- To confirm you want to perform a master reset, the E-Wand will play a series of monotone beeps.
- After you hear the beeps, press and hold the PROGRAMMING BUTTON again until you hear a SINGLE BEEP (1).
- Another short tune will play, and you will have successfully performed a master reset.
Danalock V3 Zigbee Lock
Join instructions
- Select the Start Zigbee Pairing button.
- Use the end of a paperclip to click the button in the small center hole on top of the device once, the LED will turn green.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Delete the lock from your mobile phone.
- Use the end of a paperclip to click the button in the small center hole on top of the device 10 times.
- the LED will turn red to indicate the reset command has completed.
Denon Audio Video Receiver
Join instructions
- Click the Install Device button.
- Enter the AVR's IP address in the Denon IP preference field in the driver details, click Save Preferences.
- Turn the AVR on, then select each of the available AVR inputs on the physical device, these will appear in the driver details Current States.
- Any input's display name can be changed by selecting the desired input and clicking the Edit Current Input Name command after adding the new name in the New name field.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Develco Motion sensor 2
Join instructions
- Select the Start Zigbee Pairing button.
- Insert the batteries in the sensor.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Hold the button down until the LED flashes continuously, then release the button.
- After releasing the button the sensor should flash once indicating the reset is complete.
Develco window sensor
Join instructions
- Select the Start Zigbee Pairing button.
- Insert the batteries in the sensor.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Hold the button down until the LED flashes continuously, then release the button.
- After releasing the button the sensor should flash once indicating the reset is complete.
Diese Wall Touch Smart Light Switch
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Dome Door/Window Sensor
Join instructions
- Select the Start Z-Wave Inclusion button.
- Remove the cover of the Door/Window Sensor.
- Press the Connect button quickly 3 times in a row. The LED indicator will flash 5 times indicating successful inclusion.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Remove the cover of the Door/Window Sensor.
- Press the Connect button quickly 3 times in a row. The LED indicator will flash 5 times indicating successful exclusion.
Factory reset instructions
- Open the cover and make sure the Door/Window Sensor is powered.
- Hold the Connect button for 10 seconds until the LED indicator flashes once, then release the button.
Dome Door/Window Sensor Pro
Join instructions
- Select the Start Z-Wave Inclusion button.
- Remove the sensor cover and the LED indicator will start flashing yellow.
- Press the button quickly 3 times in a row.
- The device will enter inclusion mode for 2 minutes and the LED indicator will alternate between green and red.
- After successful inclusion, the LED Indicator will flash green 3 times then flash red until the cover is replaced.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Remove the sensor cover and the LED indicator will start flashing red.
- Press the button quickly 3 times in a row.
- The LED Indicator will flash green 3 times indicating successful exclusion. It will continue flashing red (indicating tamper) until the cover is replaced.
Factory reset instructions
- Remove the Sensor cover and confirm that your Door/Window Sensor is powered up.
- Wait for 5 seconds.
- Move the Magnet and Sensor Base in and out of the closed position 6 times.
- The LED indicator will light up red for 5 seconds when reset successfully. The Door/Window Sensor’s memory will be erased to factory settings.
Dome Leak Sensor
Join instructions
- Select the Start Z-Wave Inclusion button.
- Remove the cover of the Leak Sensor by twisting it apart.
- Press the Connect button quickly 3 times in a row. The LED indicator will flash 5 times indicating successful inclusion.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Remove the cover of the Leak Sensor by twisting it apart.
- Press the Connect button quickly 3 times in a row. The LED indicator will flash 5 times indicating successful exclusion.
Factory reset instructions
- Open the back plate and make sure the Leak Sensor is powered.
- Hold the Connect button for 10 seconds until the LED indicator flashes once, then release the button.
Dome Motion Sensor
Join instructions
- Select the Start Z-Wave Inclusion button.
- Remove the cover of the Motion Sensor by twisting it apart.
- Press the Connect button quickly 3 times in a row.
- The LED indicator will flash 5 times indicating successful inclusion.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Remove the cover of the Motion Sensor by twisting it apart and make sure the Motion Sensor is powered.
- Press the Connect button quickly 3 times in a row.
- The LED indicator will flash 5 times indicating successful exclusion.
Factory reset instructions
- Remove the cover and make sure the Motion Sensor is powered.
- Hold the Connect button for 10 seconds until the LED indicator flashes once, then release the button.
Dome Mouser
Join instructions
- Select the Start Z-Wave Inclusion button.
- Remove the top cover by sliding it back and lifting up. Confirm that your Mouser is powered up.
- Press the Connect button quickly 3 times in a row.
- The LED indicator will flash 5 times indicating successful inclusion.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Remove the top cover by sliding it back and lifting up. Confirm that your Mouser is powered up.
- Press the Connect button quickly 3 times in a row.
- The LED indicator will flash 5 times indicating successful exclusion.
Factory reset instructions
- Remove the top cover by sliding it back and lifting up. Confirm that your Mouser is powered up.
- Press and hold the Connect button for at least 10 seconds and then release.
- A flashing LED indicator indicates a successful factory reset. The Mousers memory will be erased to factory settings.
Dome On/Off Plug
Join instructions
- Select the Start Z-Wave Inclusion button.
- Plug in the On/Off Plug-In Switch.
- Press the Connect button quickly 3 times in a row.
- The LED indicator will flash 5 times indicating successful inclusion.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Plug in the On/Off Plug-In Switch.
- Press the Connect Button quickly 3 times in a row.
- The LED indicator will flash 5 times indicating successful exclusion.
Factory reset instructions
- Plug in the On/Off Plug-In Switch.
- Hold the Connect button for 10 seconds until the LED Indicator flashes once, then release the button.
Dome Range Extender
Join instructions
- For proper inclusion, install the Range Extender in the final location where it will be used.
- Select the Start Z-Wave Inclusion button.
- Plug the Range Extender into an outlet or use a micro USB (not included) to power it.
- The LED will flash 5 times indicating successful inclusion.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the button quickly 3 times in a row.
- The LED will flash 5 times indicating successful exclusion.
Factory reset instructions
- Hold the button for 10 seconds until the LED flashes 10 times, then release the button.
Dome Siren
Join instructions
- Select the Start Z-Wave Inclusion button.
- Remove the back plate of the siren.
- Press the Connect button quickly 3 times in a row.
- The LED Ring will flash 5 times indicating successful inclusion.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Remove the back plate of the siren.
- Press the Connect button quickly 3 times in a row.
- The LED Ring will flash 5 times indicating successful exclusion.
Factory reset instructions
- Open the back plate and make sure the siren is powered.
- Hold the Connect button for 10 seconds until the LED Ring flashes once, then release the button.
Dome Water Shutoff
Join instructions
- Select the Start Z-Wave Inclusion button.
- Make sure the Water Main Shut-Off is powered on, then press the open/close button quickly 3 times in a row.
- The LED will stop flashing and stay on continuously upon successful inclusion.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- When prompted, press the open/close button on the Shut-Off quickly 3 times in a row.
- Wait for the exclusion process to end and the device is successfully excluded.
Factory reset instructions
- Press and hold the open/close button for at least 10 seconds then release.
- The Shut-Off’s memory will be erased to factory settings. A flashing light indicates a successful factory reset.
Dragontech Plug in Z-Wave Plus Dimmer Switch
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press the button on the front of the PD-100.
- Wait for the inclusion process to end and the device is successfully included.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the button on the front of the PD-100.
- Wait for the exclusion process to end and the device is successfully excluded.
Factory reset instructions
- Unplug the PD-100 and anything that is plugged into it.
- Press and hold the button on the front of the PD-100.
- Plug the PD-100 in while still pressing the button.
- After 3 seconds, release the button. If the button flashes, the PD-100 has been successfully reset. If not, repeat the steps to factory reset.
Eaton (Cooper Wiring Devices) Accessory Switch
Join instructions
- Select Start Z-Wave Inclusion button.
- Then press the device ON/OFF button one time to include it in the network.
- After the Device is added to the network, the blue indicator LED will stop blinking. This indicates the device is installed in the Z-Wave network.
Exclude instructions
- Select Start Z-Wave Exclusion button.
- Press the device ON/OFF button one time to exclude it from the network. The LED will start blinking.
Factory reset instructions
1. Turn the device ON.
2. Press and hold ON/OFF button for 20 second till the LED flashes for the third time.
3. Release the ON/OFF button.
4. LED will start flashing rapidly. Once the LED starts blinking slowly, that indicates the device is not part of the network.
Eaton (Cooper Wiring Devices) Dimmer
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press the device switch 1 time to include it in the network.
- The LED will stop flashing, indicating the dimmer has been successfully included.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the device switch 1 time to exclude it.
- The LED will start flashing blue, indicating the dimmer has been successfully excluded.
Factory reset instructions
- Factory reset is unavailable for this device. Instead, perform a general exclusion.
Eaton (Cooper Wiring Devices) Switch
Join instructions
1. Select Start Z-Wave Inclusion button.
2. The hub may ask you to enter 5 digit code under the QR code to install the device as a secured device. You may find this QR code on the device or included in device packaging.
3. After the Device is added to the network, the blue indicator LED will stop blinking. This indicates the device is installed in the Z-Wave network.
Exclude instructions
1. Select Start Z-Wave Exclusion button.
2. Once your controller is in exclusion mode, press the device ON/OFF button one time to exclude it from the network. The LED will start
blinking.
Factory reset instructions
1. Turn the device ON.
2. Press and hold ON/OFF button for 20 second till the LED flashes for the third time.
3. Release the ON/OFF button.
4. LED will start flashing rapidly. Once the LED starts blinking slowly, that indicates the device is not part of the network.
Eaton (Cooper Wiring Devices) Wireless Outlet / Plug
Join instructions
Press On/Off button 3 times within 1.5 seconds to put the unit into inclusion mode.
Exclude instructions
Press On/Off button 3 times within 1.5 seconds to put the unit into exclusion mode.
Factory reset instructions
- Press On/Off button 3 times within 1.5 seconds to put the unit into exclusion mode.
- Within 1 second of step 1, press and hold On/Off button for 5 seconds.
Ecobee Thermostat
Join instructions
- Use Ecobee smartphone app to set up the thermostat on the local network.
- Test thermostat functionality using app.
- Click Install App button below to install Ecobee Integration.
- Log in using your Ecobee login and password
- Add devices in the Ecobee Integration app.
Ecolink Contact Sensor
Join instructions
- Select the Start Z-Wave Inclusion button.
- Remove the battery for at least 5 seconds, then reinstall it.
- When the inclusion process is complete, the LED on the sensor will be solid blue, then go out.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Remove the battery for at least 5 seconds, then reinstall it.
- When the exclusion process is complete, the LED on the sensor will be solid blue, then go out.
Factory reset instructions
- Factory reset is unavailable for this device. Instead, perform a general exclusion.
Ecolink Door/Window Sensor
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Ecolink Flood/Freeze Sensor
Join instructions
- Select the Start Z-Wave Inclusion button.
- Remove the battery for at least 10 seconds, then reinstall it.
- If the LED starts flashing continuously, the sensor has no node ID and was not successfully included, so start from step 1 again. Make sure to remove the battery for 10 seconds if inclusion fails.
- If after 5 seconds the LED is not flashing, look on Hubitat Elevation™ for feedback on whether the sensor was included successfully. If you do not see any feedback that the sensor was included, follow the directions for exclusion of the sensor, and then try including the sensor again. If you are still having problems, you may need to add Z-Wave repeaters in-between the controller and the sensor.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Open the Flood Freeze case and remove the battery for 1 second.
- Replace the battery and the device should be excluded.
Factory reset instructions
- Factory reset is unavailable for this device. Instead, perform a general exclusion.
Ecolink Garage Door Tilt Sensor
Join instructions
- Select the Start Z-Wave Inclusion button.
- Remove the battery for at least 5 seconds, then reinstall it.
- Re-attach the battery cover and the device with enter inclusion mode.
- The LED will flash for 10 seconds and then go out. If the sensor LED continues to flash, repeat the inclusion process.
- Test the sensor before mounting it permanently. The sensor LED will flash each time the sensor position is changed.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Remove the battery for at least 5 seconds, then reinstall it.
- Re-attach the battery cover and the device with enter exclusion mode.
- The LED will flash for 10 seconds and then go out. If the sensor LED continues to flash, repeat the exclusion process from step 2.
Factory reset instructions
- Factory reset is unavailable for this device. Instead, perform a general exclusion.
Ecolink Motion Sensor
Join instructions
- Select the Start Z-Wave Inclusion button.
- Remove the battery for at least 5 seconds, then reinstall it.
- Re-attach the battery cover and the device with enter inclusion mode.
- The LED will flash for 10 seconds and then go out. If the sensor LED continues to flash, repeat the inclusion process.
- Test the sensor before mounting it permanently.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Remove the battery for at least 5 seconds, then reinstall it.
- Re-attach the battery cover and the device with enter exclusion mode.
- The LED will flash for 10 seconds and then go out. If the sensor LED continues to flash, repeat the exclusion process from step 2.
Factory reset instructions
- Factory reset is unavailable for this device. Instead, perform a general exclusion.
Ecolink Pet Immune Motion Detector
Join instructions
- Press and hold the tamper switch while inserting one of the batteries.
- Release the tamper switch within 4 seconds.
- The LED will flash 3 times every 5 seconds indicating the device is ready for pairing.
- Select the Start Zigbee Pairing button.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Press and hold the tamper switch while inserting one of the batteries.
- Release the tamper switch within 4 seconds.
- The LED will flash 3 times every 5 seconds indicating the device is ready for pairing.
Ecolink Siren
Join instructions
- Select the Start Z-Wave Inclusion button.
- Plug in the Z-Wave Plus Siren and verify a single beep sound is heard.
- The LED on the front of the unit will turn off if inclusion is successful.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Plug in the Z-Wave Plus Siren and verify a single beep sound is heard.
- The LED on the front of the unit will turn off if exclusion is successful.
Factory reset instructions
- Factory reset is unavailable for this device. Instead, perform a general exclusion.
Ecolink Smoke/CO Audio Detector
Join instructions
- Select the Start Z-Wave Inclusion button.
- Open the FireFighter case and press the learn button on the device for 1 second.
- If the LED starts flashing continually, the sensor has not been added. Repeat the inclusion steps.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Open the FireFighter case and press the learn button on the device for 1 second.
- If successfully excluded, the devices green LED should flash slowly continuously.
Factory reset instructions
- Factory reset is unavailable for this device. Instead, perform a general exclusion.
Ecolink Tilt Sensor
Join instructions
- Select the Start Z-Wave Inclusion button.
- Remove the battery for at least 5 seconds, then reinstall it.
- Re-attach the battery cover and the device will enter inclusion mode
- The LED will flash for 10 seconds and then go out. If the sensor LED continues to flash, repeat the inclusion process.
- Test the sensor before mounting it permanently. The sensor LED will flash each time the sensor position is changed.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Remove the battery for at least 5 seconds, then reinstall it.
- Re-attach the battery cover and the device with enter exclusion mode.
- The LED will flash for 10 seconds and then go out. If the sensor LED continues to flash, repeat the exclusion process from step 2.
Factory reset instructions
- Factory reset is unavailable for this device. Instead, perform a general exclusion.
Ecolink Wireless Double Rocker Switch
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press the inclusion / exclusion button on the Smart Switch.
- The LED on the front of the unit will turn off if inclusion is successful.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the inclusion / exclusion button on the Smart Switch.
- Wait for the exclusion process to end and the device is successfully excluded.
Factory reset instructions
- Factory reset is unavailable for this device. Instead, perform a general exclusion.
Ecolink Wireless Double Toggle Switch
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press the inclusion / exclusion button on the switch.
- The LED on the front of the switch will turn off if successfully included.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the inclusion / exclusion button on the switch.
- Wait for the exclusion process to end and the device is successfully excluded.
Factory reset instructions
- Factory reset is unavailable for this device. Instead, perform a general exclusion.
Ecolink Wireless Rocker Switch
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press the inclusion / exclusion button on the Smart Switch.
- The LED on the front of the unit will turn off if inclusion is successful.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the inclusion / exclusion button on the Smart Switch.
Factory reset instructions
- Factory reset is unavailable for this device. Instead, perform a general exclusion.
Ecolink Wireless Toggle Switch
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press the inclusion / exclusion button on the Smart Switch.
- The LED on the front of the unit will turn off if inclusion is successful.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the inclusion / exclusion button on the Smart Switch.
Factory reset instructions
- Factory reset is unavailable for this device. Instead, perform a general exclusion.
Enerwave Ceiling Mounted PIR Motion Sensor
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press the inclusion/exclusion button on the sensor 3 times.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the inclusion/exclusion button on the sensor 3 times.
Factory reset instructions
- To reset the sensor, simply press the exclusion button on the sensor 3 times and hold for 3 seconds on the 3rd press.
Enerwave Plug-In Outlet
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
ESTTECH grow light
Join instructions
- Select the Start Zigbee Pairing button.
- Press the network switch button once every second for three times.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Eva Logik Smart Plug
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press the button on the switch 3 times within 2 seconds.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the top button on the switch 3 times within 2 seconds.
Factory reset instructions
- Hold the button for 5 seconds when powered on.
Eva Logik Smart Plug
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press the button on the switch 3 times within 2 seconds.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the button on the switch 3 times within 2 seconds.
Factory reset instructions
- Press and hold the top button for at least 3 seconds while you plug the smart switch into a receptacle.
Everspring Door/Window Detector
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press the tamper switch three times within 1.5 seconds and the sensor will enter inclusion mode.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the tamper switch three times within 1.5 seconds and the sensor will enter exclusion mode. The LED will light up once, each time the tamper switch is pressed.
Factory reset instructions
- Press the tamper switch three times within 1.5 seconds. The LED will be steady on.
- Within 1 second, press and hold the tamper switch until LED is off.
- The LED will cycle on for 2 seconds and off for 2 seconds indicating the sensor has been reset to factory defaults.
Everspring Everspring Illumination Sensor
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press the ESC button three times within 1.5 seconds and the sensor will enter inclusion mode. The sensor LED will flash.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the ESC button three times within 1.5 seconds and the sensor will enter exclusion mode. The sensor LED will flash.
Factory reset instructions
- Press the ESC button three times within 1.5 seconds.
- Within 1 second, press and hold the ESC button.
- The sensor will long beep. Keep holding the link key until the long beep stops.
Everspring Flood Detector
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press the link key three times within 1.5 seconds and the sensor will enter inclusion mode. The sensor will beep once each time the link key is pressed.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the link key three times within 1.5 seconds and the sensor will enter exclusion mode. The sensor will beep once each time the link key is pressed.
Factory reset instructions
- Press the link key three times within 1.5 seconds. The sensor will beep each time the link key is pressed.
- Within 1 second, press and hold the link key. The sensor will long beep for 5 seconds. Keep holding the link key until the long beep stops.
- The LED will cycle on for 2 seconds and off for 2 seconds indicating the sensor has been reset to factory defaults.
Everspring PIR Detector
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press the tamper switch three times within 1.5 seconds and the sensor will enter inclusion mode.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the tamper switch three times within 1.5 seconds and the sensor will enter exclusion mode.
Factory reset instructions
- Press tamper switch three times within 1.5 seconds. The LED will be steady on.
- Within 1 second, press and hold the tamper switch until LED is off.
- The LED will cycle on for 2 seconds and off for 2 seconds indicating the sensor has been reset to factory defaults.
Everspring Smoke Detector
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press the tamper switch three times within 1.5 seconds and the sensor will enter inclusion mode. The LED flashes and the buzzer sounds when the link key is pressed.
- The detector will stay awake and remain in inclusion mode for 10 minutes, or until the device has successfully been included.
- The LED will light for 1 second and the buzzer will sound for 1 second to indicate the detector has been successfully included.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the tamper switch three times within 1.5 seconds and the sensor will enter exclusion mode. The LED flashes and the buzzer sounds when the link key is pressed.
- The detector will stay awake and remain in exclusion mode for 10 minutes, or until the device has successfully been excluded.
- The LED will light for 1 second and the buzzer will sound for 1 second to indicate the detector has been successfully excluded.
Factory reset instructions
- Press tamper switch three times within 1.5 seconds. The LED flashes and the buzzer sounds when the link key is pressed.
- Within 1 second, press and hold the tamper switch for 5 seconds until the LED is off.
- The LED will light for 5 seconds and the buzzer will sound for 5 seconds.
Everspring Temperature/Humidity Sensor
Join instructions
- Select the Start Z-Wave Inclusion button.
- Pressing the temperature unit/linking key 3 times within 1.5 seconds will enter inclusion mode. The linking signal symbol will flash on the display.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Pressing the temperature unit/linking key 3 times within 1.5 seconds will enter exclusion mode. The linking signal symbol will flash on the display.
- When the radio frequency status shows no signal, the device has been excluded from any previously joined Z-Wave networks.
Factory reset instructions
- Pressing the temperature unit/linking key 3 times within 1.5 seconds will enter inclusion mode. The linking signal symbol will flash on the display.
- Within 1 second, press the temperature unit/linking key again, and the sensor will emit a long beep. Keep holding the temperature unit/linking key until the long beep stops.
- When the radio frequency status shows no signal, the device has been excluded from any previously joined Z-Wave networks and has been reset to factory defaults.
Evolve Isolated Contact Fixture Module
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press the button on the device once to include it.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Exclude the module by tapping the button 3 times, then press and hold for 10 seconds.
- LFM-20 release 5.41 requires that you tap 2 times, then press and hold for 10 seconds.
Factory reset instructions
- Factory reset is unavailable for this device. Instead, perform a general exclusion.
eWeLink 10A Outlet
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
eWeLink Relay
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Fibaro Button
Join instructions
- Select the Start Z-Wave Inclusion button.
- Click the button at least 6 times.
- Wait for the device to be included into the system.
- Click the button 4 times to wake it up.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Click the Button at least 6 times.
- Wait for the exclusion process to end and the device is successfully excluded.
Factory reset instructions
- Click the button exactly five times.
- Press and hold the button for at least 5 seconds.
Fibaro Door/Window Sensor 2
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press one of the TMP buttons quickly, 3 times in a row, while keeping other button pressed.
- Wait for the inclusion process to end and the device is successfully included.
Exclude instructions
- Select the Start Z-Wave Inclusion button.
- Press one of the TMP buttons quickly, 3 times in a row, while keeping other button pressed.
- The device will be excluded from the Z-Wave network.
Factory reset instructions
- Open the cover and remove the battery.
- Install the battery while holding both TMP buttons.
- The LED indicator will be flashing slowly for 5 seconds, but keep holding the buttons.
- Release one button when the LED indicator starts flashing quickly.
- Click the released button once to confirm initiation of the reset procedure.
- Wait a few seconds for a long flash of the LED indicator. Do not remove the battery.
- The LED indicator will flash 5 times quickly to confirm reset of the device.
Fibaro Fibaro RGBW Controller
Join instructions
(Auto Inclusion)
- Make sure the RGBW Controller is not connected to a supply.
- Select the Start Z-Wave Inclusion button.
- Connect voltage supply to auto-include the RGBW Controller.
- The RGBW Controller will be automatically recognized and included in the Z-Wave network.
(Manual Inclusion)
- Make sure the RGBW Controller is not connected to a supply.
- To disable auto-inclusion press the B button briefly, after re-connecting the RGBW Controller to its supply voltage.
- Select the Start Z-Wave Inclusion button.
- Triple click the B button or any switch connected to I1-I4 inputs.
- The RGBW Controller will be recognized and included in the Z-Wave network.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Triple click the B button or any switch connected to I1-I4 inputs.
- The device will be excluded from the Z-Wave network.
Factory reset instructions
- Disconnect the supply voltage.
- Press and hold the B button located inside the RGBW Controllers casing.
- Connect the the supply voltage, while still holding the B button.
- Release the B button.
- The B channel will turn on (blue channel).
- Disconnect the power supply.
Fibaro Flood Sensor
Join instructions
- Select the Start Z-Wave Inclusion button.
- Remove the battery for 10 seconds, and then re-install it
- Wait for the inclusion process to end and the device is successfully included.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the TMP button quickly, 3 times in a row.
- The device will be excluded from the Z-Wave network.
Factory reset instructions
- Make sure the sensor is powered.
- Press and hold the TMP button.
- Wait for the visual LED indicator to glow yellow (4th position of the MENU).
- Release the TMP button.
- Click the TMP button once to confirm selection.
- After a few seconds the device will restart with factory settings, which is signaled with the red visual indicator color and an acoustic signal.
Fibaro Flood Sensor ZW5
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press the TMP button quickly, 3 times in a row.
- Wait for the inclusion process to end and the device is successfully included.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the TMP button quickly, 3 times in a row.
- The device will be excluded from the Z-Wave network.
Factory reset instructions
- Make sure the sensor is powered.
- Press and hold the TMP button.
- Wait for the visual LED indicator to glow yellow (4th position of the MENU).
- Release the TMP button.
- Click the TMP button once to confirm selection.
- After a few seconds the device will restart with factory settings, which is signaled with the red visual indicator color and an acoustic signal.
Fibaro KeyFob
Join instructions
- Select the Start Z-Wave Inclusion button.
- The LED will pulse White during the inclusion process.
- Wait for the inclusion process to end.
- Successful inclusion will be confirmed by the remotes Green LED.
Exclude instructions
- Select the Start Z-Wave Inclusion button.
- Click O and – simultaneously.
- Click ? or X until LED is Green.
- Click + to confirm selection.
- The device will be excluded from the Z-Wave network.
Factory reset instructions
- Click O and – simultaneously.
- Click ? or X until LED is Yellow - reset the device.
- Click + to confirm selection, or if you do not wish to reset at this time, click – to exit the menu.
- The LED will pulse Yellow twice to confirm the device has been reset.
Fibaro Motion Sensor ZW5
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press the B button quickly, three times in a row.
- Wait for the inclusion process to end and the device is successfully included.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the B button quickly, three times in a row.
- The device will be excluded from the Z-Wave network.
Factory reset instructions
- Open the cover
- Press and hold the B button.
- Wait for visual indicator to glow Yellow (2nd menu position).
- Release the B button and then briefly click the B button to confirm selection
- After a few seconds the device will be reset, which is signaled with the Red, fading visual indicator color.
Fibaro Radiator Thermostat
Join instructions
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Quickly 3 times in a row, press the at the base of the thermostat head.
- The LED ring will start flashing White.
- Successful inclusion confirmed by the LED ring showing Green.
Exclude instructions
- From the device's details page, select Remove Device, then Remove
- Quickly 3 times in a row, press the at the base of the thermostat head.
- The LED ring will start flashing White.
- Successful exclusion confirmed by the LED ring showing Red.
Factory reset instructions
- Press and hold the button at the base of the thermostat head.
- Release when the LED ring is Yellow.
- Briefly press the button to confirm selection.
- The device will reset and then go into Standby Mode.
- Briefly press the button to activate the thermostat again.
Fibaro Single Switch 2
Join instructions
- Identify the S1 switch.
- Select the Start Z-Wave Inclusion button
- Press the S1 switch quickly 3 times.
- Wait for the inclusion process to end and the device is successfully included.
Exclude instructions
- Select the Start Z-Wave Exclusion button
- Press the S1 switch quickly 3 times.
- The device will be excluded from the Z-Wave network.
Factory reset instructions
- Switch off the mains voltage (disable the breaker).
- Remove the Switch 2 from the wall switch box.
- Switch on the mains voltage.
- Press and hold the B button to enter the menu until the visual LED indicator is Yellow.
- Quickly release and click the B button again.
- After a few seconds the device will be restarted, which is signaled by the Red LED indicator color.
Fibaro Universal Binary Sensor
Join instructions
- Select the Start Z-Wave Inclusion button.
- Quickly press the B button 3 times (the button is located in the center of the device).
- Watch the status in the device details page to confirm proper operation.
- NOTE: Every time changes are made to the configuration of TP and TD lines (1-wire), (i.e. When DS18B20 temperature sensors are Included or Excluded), it is necessary to perform an exclusion and repeated inclusion of the sensor modules to the hub. The system will enter into the programming mode only once all the connected sensors have been detected (about 10 seconds).
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Quickly press the B button 3 times (the button is located in the center of the device).
- Wait for the exclusion process to end and the device is successfully excluded.
Factory reset instructions
- Remove and re-connect the power supply while holding down the B button (the button is located in the center of the device).
- After 10 seconds, remove and re-connect the power supply again.
- The settings of the device are now reset.
Fibaro Wall Plug
Join instructions
- Plug the device into a socket.
- The LED frame will glow red signaling it is not being included (If is doesn't you must first perform a general exclusion and then a factory reset).
- Select the Start Z-Wave Inclusion button.
- Quickly, triple click the button located on the casing.
- Wait for the inclusion process to end and the device is successfully included.
Exclude instructions
- Plug the device into a socket.
- Select the Start Z-Wave Exclusion button.
- The LED frame will glow green signaling it is currently included in a Z-Wave network (If it doesn't, then the exclusion process is not needed at this time).
- Quickly, triple click the button located on the casing.
- The device will be excluded from the Z-Wave network.
Factory reset instructions
- Make sure the device is powered.
- Press and hold the button.
- Wait for the LED frame to glow yellow (3rd menu position).
- Release the button and then briefly click the button once to confirm the selection.
- After a few seconds the device will restart with factory settings, which is signaled with the red frame color.
First Alert Smoke & CO Alarm
Join instructions
- Slide battery door open and insert batteries.
- Select the Start Z-Wave Inclusion button.
- Press and hold the test button. Keep it held down as you slide the battery drawer closed. You may then release the button and the alarm will remain awake for 30 seconds on inclusion.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Slide battery door open, then remove and re-insert batteries.
- Press and hold the test button. Keep it held down as you slide the battery drawer closed. You may then release the button and the alarm will be excluded from the network.
Factory reset instructions
- Power up the device with the test button held down for 10 or more seconds.
- The device will reset all Z-Wave settings and leave the network. NOTE: The device will not remain awake after resetting and will go into standby mode.
First Alert Smoke & CO Alarm
Join instructions
- Slide battery door open and insert batteries.
- Select the Start Z-Wave Inclusion button.
- Press and hold the test button. Keep it held down as you slide the battery drawer closed. You may then release the button and the alarm will remain awake for 30 seconds on inclusion.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Slide battery door open, then remove and re-insert batteries.
- Press and hold the test button. Keep it held down as you slide the battery drawer closed. You may then release the button and the alarm will be excluded from the network.
Factory reset instructions
- Power up the device with the test button held down for 10 or more seconds.
- The device will reset all Z-Wave settings and leave the network. NOTE: The device will not remain awake after resetting and will go into standby mode.
FortrezZ MIMO2+
Join instructions
- Select the Start Z-Wave Inclusion button.
- Briefly press the program button once.
- The status LED will flash when the device has been included.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Briefly press the program button once.
- The status LED will flash when the device has been excluded.
Factory reset instructions
- Press and hold the program button for 15 seconds and then release.
FortrezZ MIMOlite
Join instructions
- Select the Start Z-Wave Inclusion button.
- When the LED has a periodic single flash, the unit will be automatically included.
- The LED will flash 2 times when the device is successfully included.
- If the LED flashes 4 times, then the button has been previously pressed and automatic inclusion mode is no longer active. In this case, reset the device and repeat inclusion steps.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Briefly press the program button once.
- The status LED will flash 4 times when the device has been excluded from the Z-Wave network.
Factory reset instructions
- Press and hold the program button for 15 seconds and then release.
frient Air Quality Sensor
Join instructions
- Select the Start Zigbee Pairing button.
- Insert the batteries in the sensor.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Hold the button down until the LED flashes continuously, then release the button.
- After releasing the button the sensor should flash once indicating the reset is complete.
frient Entry Sensor
Join instructions
- Select the Start Zigbee Pairing button.
- Insert the batteries in the sensor.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Hold the button down until the LED flashes continuously, then release the button.
- After releasing the button the sensor should flash once indicating the reset is complete.
frient Entry Sensor Pro
Join instructions
- Select the Start Zigbee Pairing button.
- Insert the batteries in the sensor.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Hold the button down until the LED flashes continuously, then release the button.
- After releasing the button the sensor should flash once indicating the reset is complete.
frient Heat Alarm
Join instructions
- Select the Start Zigbee Pairing button.
- Insert the batteries in the sensor.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Hold the button down until the LED flashes continuously, then release the button.
- After releasing the button the sensor should flash once indicating the reset is complete.
frient Motion Sensor
Join instructions
- Select the Start Zigbee Pairing button.
- Insert the batteries in the sensor.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Hold the button down until the LED flashes continuously, then release the button.
- After releasing the button the sensor should flash once indicating the reset is complete.
frient Motion Sensor Pro
Join instructions
- Select the Start Zigbee Pairing button.
- Insert the batteries in the sensor.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Hold the button down until the LED flashes continuously, then release the button.
- After releasing the button the sensor should flash once indicating the reset is complete.
frient Smart Humidity Sensor
Join instructions
- Select the Start Zigbee Pairing button.
- Insert the batteries in the sensor.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Hold the button down until the LED flashes continuously, then release the button.
- After releasing the button the sensor should flash once indicating the reset is complete.
frient Smart Mini Plug
Join instructions
- Select the Start Zigbee Pairing button.
- Push the button on the smart plug.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Hold the button down until the LED flashes continuously, then release the button.
- Do not unplug or switch the device off until the LED turns off.
frient Smart Plug Mini
Join instructions
- Select the Start Zigbee Pairing button.
- Push the button on the smart plug.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Hold the button down until the LED flashes continuously, then release the button.
- Do not unplug or switch the device off until the LED turns off.
frient Smart Siren
Join instructions
- Select the Start Zigbee Pairing button.
- Plug in the Siren.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Hold the button down until the LED flashes continuously, then release the button.
- After releasing the button the sensor should flash once indicating the reset is complete.
frient Smoke Alarm
Join instructions
- Select the Start Zigbee Pairing button.
- Insert the batteries in the sensor.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Hold the button down until the LED flashes continuously, then release the button.
- After releasing the button the sensor should flash once indicating the reset is complete.
GE/Jasco Enbrighten Smart Dimmer
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press and release the top or bottom of the wireless smart dimmer rocker to include it.
- Note: While some switches have a small tab to pull out, commonly referred to as an air gap, certain older GE switches do not disable power to the internal Z-Wave radio when the air gap is pulled. In such cases, where a mains powered device is refusing to include, perform an exclusion and then cut the power at the breaker box for 30 seconds before attempting the inclusion procedure again.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press and release the top or bottom of the wireless smart dimmer rocker to exclude it.
Factory reset instructions
- Factory reset is unavailable for this device. Instead, perform a general exclusion.
GE/Jasco Enbrighten Smart Switch
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press and release the top or bottom of the wireless smart switch rocker to include it.
- Note: While some switches have a small tab to pull out, commonly referred to as an air gap, certain older GE switches do not disable power to the internal Z-Wave radio when the air gap is pulled. In such cases, where a mains powered device is refusing to include, perform an exclusion and then cut the power at the breaker box for 30 seconds before attempting the inclusion procedure again.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press and release the top or bottom of the wireless smart switch rocker to exclude it.
Factory reset instructions
- Quickly press ON (Top) button 3 times then immediately press the OFF (Bottom) button 3 times.
- The LED will flash ON/OFF 5 times when completed successfully.
GE/Jasco In-Wall Smart Dimmer
Join instructions
- Select the Start Zigbee Pairing button.
- Press the top rocker paddle once.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Press the top rocker paddle 10 times quickly.
GE/Jasco In-Wall Smart Dimmer
Join instructions
- Select the Start Zigbee Pairing button.
- Press the top rocker paddle once.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Press the top rocker paddle 10 times quickly.
GE/Jasco In-Wall Smart Dimmer
Join instructions
- Select the Start Zigbee Pairing button.
- Press the top rocker paddle once.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Press the top rocker paddle 10 times quickly.
GE/Jasco In-Wall Smart Dimmer
Join instructions
- Select the Start Zigbee Pairing button.
- Press the top rocker paddle once.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Press the top rocker paddle 10 times quickly.
GE/Jasco In-Wall Smart Dimmer
Join instructions
- Select the Start Zigbee Pairing button.
- Press the top rocker paddle once.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Press the top rocker paddle 10 times quickly.
GE/Jasco In-Wall Smart Dimmer
Join instructions
- Remove power from the dimmer at the circuit breaker.
- Select the Start Zigbee Pairing button.
- Restore power to the Smart Dimmer at the circuit breaker.
- Pairing Begins Automatically: LED Status Indicator flashes as the Smart Dimmer automatically scans for a compatible network controller to pair with.
- After the Smart Dimmer is located and paired to the Zigbee network, the LED Status Indicator will stop flashing on the Smart Dimmer.
- Note: LED Status Indicator stops flashing if a timeout occurs: Auto-Scan mode will eventually time out if the device has not joined a Zigbee network. Press and release the front panel to restart pairing process following timeout.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Lift the air-gap switch at the bottom of the rocker to OFF position to power down the device.
- Hold down the UP button.
- Push In the air-gap switch to ON position to power up the device.
- Release the UP button within 4 seconds of power up.
GE/Jasco In-Wall Smart Outlet
Join instructions
- Select the Start Zigbee Pairing button.
- Press the button once.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Press the button 10 times quickly.
GE/Jasco In-Wall Smart Paddle Switch
Join instructions
- Select the Start Zigbee Pairing button.
- Press the top rocker paddle once.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Press the top rocker paddle 10 times quickly.
GE/Jasco In-Wall Smart Switch
Join instructions
- Select the Start Zigbee Pairing button.
- Press the top rocker paddle once.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Press the top rocker paddle 10 times quickly.
GE/Jasco In-Wall Smart Switch
Join instructions
- Select the Start Zigbee Pairing button.
- Press the top rocker paddle once.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Press the top rocker paddle 10 times quickly.
GE/Jasco In-Wall Smart Switch
Join instructions
- Select the Start Zigbee Pairing button.
- Press the top rocker paddle once.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Press the top rocker paddle 10 times quickly.
GE/Jasco In-Wall Smart Switch
Join instructions
- Remove power from the dimmer at the circuit breaker.
- Select the Start Zigbee Pairing button.
- Restore power to the Smart Dimmer at the circuit breaker
- Pairing Begins Automatically: LED Status Indicator flashes as the Smart Dimmer automatically scans for a compatible network controller to pair with.
- After the Smart Dimmer is located and paired to the Zigbee network, the LED Status Indicator will stop flashing on the Smart Dimmer.
- Note: LED Status Indicator stops flashing if a timeout occurs: Auto-Scan mode will eventually time out if the device has not joined a Zigbee network. Press and release the front panel to restart pairing process following timeout.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Tap the top of the rocker (ON Switch) with 10 quick short presses.
GE/Jasco In-Wall Smart Toggle Switch
Join instructions
- Select the Start Zigbee Pairing button.
- Toggle the switch on once.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Toggle the switch 10 times quickly.
GE/Jasco Plug-In Dimmer Module Dual Controlled Plug
Join instructions
- Select the Start Zigbee Pairing button.
- Press the button once.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Press the button 10 times quickly.
GE/Jasco Plug-In Dimmer Module Dual Controlled Plug
Join instructions
- Select the Start Zigbee Pairing button.
- Press the button once.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Press the button 10 times quickly.
GE/Jasco Plug-In Outdoor Smart Outlet
Join instructions
- Select the Start Zigbee Pairing button.
- Press the button once.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Press the button 10 times quickly.
GE/Jasco Plug-In Smart Switch
Join instructions
- Select the Start Zigbee Pairing button.
- Hold the button and plug in the switch.
- Keep the button held down for 10 seconds.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Unplug the switch.
- Hold the button and plug in the switch.
- Keep the button held down for 10 seconds.
GE/Jasco Plug-In Smart Switch With Dual Controlled Outlets
Join instructions
- Select the Start Zigbee Pairing button.
- Press the button once.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Press the button 10 times quickly.
GE/Jasco Plug-In Smart Switch With Dual Controlled Outlets
Join instructions
- Select the Start Zigbee Pairing button.
- Press the button once.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Press the button 10 times quickly.
GE/Jasco Plug-In Switch Module Dual Controlled Plug
Join instructions
- Select the Start Zigbee Pairing button.
- Press the button once.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Press the button 10 times quickly.
GE/Jasco Smart Dimmer
Join instructions
- Select Start Z-Wave Inclusion button
- Press and release the top button of the wireless smart switch
Exclude instructions
- Select Start Z-Wave Exclusion button.
- Press and release the top button of the wireless smart switch
Factory reset instructions
Quickly press ON (Top) button 3 times then immediately press the OFF (Bottom) button 3 times. The LED will flash ON/OFF 5 times when completed successfully.
GE/Jasco Smart Dimmer
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press and release the top or bottom of the wireless smart dimmer rocker to include it.
- Note: While some switches have a small tab to pull out, commonly referred to as an air gap, certain older GE switches do not disable power to the internal Z-Wave radio when the air gap is pulled. In such cases, where a mains powered device is refusing to include, perform an exclusion and then cut the power at the breaker box for 30 seconds before attempting the inclusion procedure again.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press and release the top or bottom of the wireless smart dimmer rocker to exclude it.
Factory reset instructions
- Quickly press ON (Top) button 3 times then immediately press the OFF (Bottom) button 3 times.
- The LED will flash ON/OFF 5 times when completed successfully.
GE/Jasco Smart Motion Switch
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press and release the top or bottom button on the smart switch to include it.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press and release the top or bottom button on the smart switch to exclude it.
Factory reset instructions
- Press and release the top button 10 times within 5 seconds.
GE/Jasco Smart Switch
Join instructions
- Select Start Z-Wave Inclusion button
- Press and release the top button of the wireless smart switch
Exclude instructions
- Select Start Z-Wave Exclusion button.
- Press and release the top button of the wireless smart switch
Factory reset instructions
Quickly press ON (Top) button 3 times then immediately press the OFF (Bottom) button 3 times. The LED will flash ON/OFF 5 times when completed successfully.
GE/Jasco Smart Switch
Join instructions
- Select Start Z-Wave Inclusion button
- Press and release the top button of the wireless smart switch
Exclude instructions
- Select Start Z-Wave Exclusion button.
- Press and release the top button of the wireless smart switch
Factory reset instructions
Quickly press ON (Top) button 3 times then immediately press the OFF (Bottom) button 3 times. The LED will flash ON/OFF 5 times when completed successfully.
GE/Jasco Smart Switch
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press and release the top or bottom of the wireless smart switch rocker to include it.
- Note: While some switches have a small tab to pull out, commonly referred to as an air gap, certain older GE switches do not disable power to the internal Z-Wave radio when the air gap is pulled. In such cases, where a mains powered device is refusing to include, perform an exclusion and then cut the power at the breaker box for 30 seconds before attempting the inclusion procedure again.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press and release the top or bottom of the wireless smart switch rocker to exclude it.
Factory reset instructions
- Quickly press ON (Top) button 3 times then immediately press the OFF (Bottom) button 3 times.
- The LED will flash ON/OFF 5 times when completed successfully.
GE/Jasco Tamper Resistant Smart Outlet
Join instructions
- Select the Start Zigbee Pairing button.
- Press the button once.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Press the button three times, then press and hold the button for at least three seconds. The LED will blink three times to confirm.
GLEDOPTO Mini RGB+CCT Controller
Join instructions
- Remove power from the GLEDOPTO Mini RGB+CCT controller.
- Select the Start Zigbee Pairing button.
- Power ON the device and within 2 seconds remove power.
- Repeat the OFF and ON 4 times in a row.
- The device will reset to factory default on the 5th time the power is applied.
- Reset is confirmed by the lights flashing 4 times.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Power ON the device and within 2 seconds remove power.
- Repeat the OFF and ON 4 times in a row.
- The device will reset to factory default on the 5th time the power is applied.
- Reset is confirmed by the lights flashing 4 times.
Global Cache Global Connect IR Module
Join instructions
- Click the Install Device button.
- Enter the IR modules IP address in the IP preference field in the driver details, click Save Preferences.
- Navigate to the IR Modules configuration web page (enter the device IP address in your browser), click the IR Settings menu item.
- Set each port to Sensor, then click Apply Settings.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Global Cache Global Connect Relay Module
Join instructions
- Click the Install Device button.
- Enter the Relay modules IP address in the IP preference field in the driver details, click Save Preferences.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
GoControl Garage Door Controller
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press and release the Link button to include the device.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press and release the Link button to exclude the device.
Factory reset instructions
- Reset the controller by pressing the Link button 5 times.
- A quick beep followed by a longer beep will indicate proper reset for the GD00Z series or ND00Z.
GoControl Z-Wave Thermostat
Join instructions
- Press FAN button for 5 seconds until SETUP appears in status display line.
- Use ? and? buttons to select ZWAVE in status display line.
- Press Mode button to select menu item.
- Click Start Z-Wave Inclusion button.
- Thermostat's status display line should say INSTALL, press Mode button to select.
Exclude instructions
- Press FAN button for 5 seconds until SETUP appears in status display line.
- Use ? and? buttons to select ZWAVE in status display line.
- Press Mode button to select menu item.
- Click Start Z-Wave Exclusion button.
- Thermostat's status display line should say REMOVE, press Mode button to select.
Factory reset instructions
- Take the batteries out.
- Press and hold MODE and FAN buttons.
- Insert batteries while holding MODE and FAN buttons.
- Thermostat's status display line will show alphanumeric product id (like NTBZ48).
- Once you see the message, release MODE and FAN buttons.
Google Google Home Assistant
Join instructions
Click Install Integration App above to begin a guided integration process.
Graber Z-Wave+ Roller Blinds (Motorized Shades)
Join instructions
- Select the Start Z-Wave Inclusion button.
- Place the single channel remote in programming mode by pressing and holding the programming button until the LED light bar begins to flash Green.
- Release the button.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Place the single channel remote in programming mode by pressing and holding the programming button until the LED light bar begins to flash Green.
- Release the button.
Factory reset instructions
- Press and hold the button on the headrail end cap for 7 seconds or until the shade jogs once.
- Release the button.
- NOTE: This will not reset the shade limits.
Halo Labs Halo+ Smoke Alarm
Join instructions
- Select the Start Zigbee Pairing button.
- Once Halo greets you, it will automatically begin searching for a Zigbee network. Halo will glow for a couple minutes before timing out.
- To awaken the detector, double-tap the center button or hold the button for approximately 3 or more seconds.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- To reset, hold down center button for approximately 20 or more seconds.
Hampton Bay Ceiling Fan Controller
Join instructions
- Select the Start Zigbee Pairing button.
- Turn on your fan.
- When successful, the fan will turn on at low speed and the light will flash 3 times.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Turn off your fan for 3 seconds, then turn it on for 3 seconds (Repeat 5 times).
- The light will flash 3 times when the factory reset is successful.
Hank Four-Key Scene Controller
Join instructions
- Select the Start Z-Wave Inclusion button.
- Insert the battery.
- Triple click the center "Z-button".
- If inclusion is successful, the LED will flash blue for less than 5 seconds, and then it will remain solid for 15 seconds.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- If exclusion is successful, the LED will flash orange for less than 5 seconds, and then it will remain solid for 3 seconds.
Factory reset instructions
- Press and hold the center "Z-button" for 20 seconds.
- Release the button after 20 seconds and the LED will stay yellow for 3 seconds.
- Within the 3 second period where the LED is yellow, short-press the Z-button to reset the controller to factory defaults.
Hank One-Key Scene Controller
Join instructions
- Select the Start Z-Wave Inclusion button.
- Insert the battery.
- Triple click the center "Z-button".
- If inclusion is successful, the LED will flash blue for less than 5 seconds, and then it will remain solid for 15 seconds.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- If exclusion is successful, the LED will flash orange for less than 5 seconds, and then it will remain solid for 3 seconds.
Factory reset instructions
- Press and hold the center "Z-button" for 20 seconds.
- Release the button after 20 seconds and the LED will stay yellow for 3 seconds.
- Within the 3 second period where the LED is yellow, short-press the Z-button to reset the controller to factory defaults.
Hank RGBW LED Bulb
Join instructions
- Select the Start Z-Wave Inclusion button.
- Make sure power to the bulb is disconnected and the RGB BULB is close to the hub.
- Insert the bulb into a socket and then turn it on.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Toggle power to the bulb off and on 3 times quickly.
- Within 3 times toggling the bulb, the final ending state of the switch or plug must be on.
- If the exclusion is successful, the RGB BULB will quickly flash orange for less than 5 seconds, and then it will remain solid for 3 seconds.
- The bulb will remain warm white after the exclusion procedure is complete.
Factory reset instructions
- Factory reset is unavailable for this device. Instead, perform a general exclusion.
Heatit Heatit Z-Water
Join instructions
- Select Start Z-Wave Inclusion button.
- press the ”INCLUSION” button once on the device.
Exclude instructions
- Select Start Z-Wave Exclusion button.
- press the ”INCLUSION” button once on the device.
Factory reset instructions
Heatit Z-Water can be factory reset by pressing the small button through the little hole, marked with the text “INCLUSION”,
in front of the Heatit Z-Water regulator for at least 10 seconds.
Heatit Heatit ZM Single Relay
Join instructions
- Select Start Z-Wave Inclusion button.
- Add mode is indicated on the device by a blinking green LED. This lasts until timeout occurs after 90 seconds, or until the module has been added to the network. The LED will light up for 3 seconds if adding is successful.
Exclude instructions
- Select Start Z-Wave Exclusion button.
- Remove mode is indicated on the device by a blinking green LED. This lasts until timeout occurs after 90 seconds, or until the module has been removed from the network. The LED will light up for 3 seconds if removing is successful.
Factory reset instructions
Press and hold the configuration button. After 3 seconds the LED will start to blink in green. After 20 seconds the LED will stop blinking and emit a constant light. You may now release the button.
Heatit Heatit ZM Thermostat
Join instructions
- Select Start Z-Wave Inclusion button.
- Add mode is indicated on the device by a blinking green LED. It indicated this for 90 seconds until a timeout occurs, or until the module has been added to the network. To start the configuration process, press the configuration button 3 times in rapid succession. The LED will light up green for 3 seconds if adding is successful.
Exclude instructions
- Select Start Z-Wave Exclusion button.
- Remove mode is indicated on the device by a blinking green LED. It indicated this for 90 seconds until a timeout occurs, or until the module has been removed from the network. To start the configuration process, press the configuration button 3 times in rapid succession. The LED will light up green for 3 seconds if removing is successful.
Factory reset instructions
Press and hold the configuration button. After 3 seconds the LED will start to blink in green. After 20 seconds the LED will start to blink green rapidly for 5 seconds. You may now release the button
Heatit Z-Dim
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press the main button on the dimmer 6 times quickly.
- Wait for the inclusion process to end and the device is successfully included.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the main button on the dimmer 6 times quickly.
- Wait for the exclusion process to end and the device is successfully excluded.
Factory reset instructions
- By pressing and holding the main button for 20 seconds, the dimmer will be factory reset.
- The connected light source will blink once and go in the OFF state if successfully reset.
Heatit Z-Repeater
Join instructions
- Select the Start Z-Wave Inclusion button.
- Plug-in the device and within 1.5 seconds, press the function button 3 times.
- Wait for the inclusion process to end and the device is successfully included.
Exclude instructions
- Unplug the device.
- Select the Start Z-Wave Exclusion button.
- Plug-in the device and within 1.5 seconds, press the function button 3 times.
- Wait for the exclusion process to end and the device is successfully excluded.
Factory reset instructions
- Factory reset is unavailable for this device. Instead, perform a general exclusion.
Heatit Z-Smoke 230V
Join instructions
- When power is applied, the smoke detector initiates a 1 minute warm-up period and will automatically enter inclusion mode.
- NOTE: After the calibration process is finished, access inclusion mode by pressing the function button 3 times within 1.5 seconds.
- Select the Start Z-Wave Inclusion button.
- Wait for the inclusion process to end and the device is successfully included.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the function button 3 times within 1.5 seconds.
- Wait for the exclusion process to end and the device is successfully excluded.
Factory reset instructions
- Factory reset is unavailable for this device. Instead, perform a general exclusion.
Heatit Z-Temp2
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press the link button 3 times quickly.
- The thermostat will display INC when the thermostat is successfully included.
- If inclusion fails, Err (error) will appear.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the link button 3 times quickly.
- Wait for the exclusion process to end and the device is successfully excluded.
Factory reset instructions
- Press and hold the link button for 20 seconds.
- rES will be displayed when reset is complete.
Heatit Z-TRM3
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press and hold the center button until OFF is shown on the display (approx. 10 seconds).
- Press the down button 5 times until you reach CON.
- Press and hold until the display shows a rotating light pattern. The thermostat will display INC when the thermostat has been successfully included.
- If inclusion fails, Err (error) will appear.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the down button 5 times until you reach CON.
- Press the center (confirm) for approximately 2 seconds.
- Wait for the exclusion process to end and the device is successfully excluded.
Factory reset instructions
- Press both the Right and Center (down and confirm) buttons for 20 seconds.
- The thermostat will be factory reset.
Heiman Zigbee Gas Detector
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- From the device's details page, select Remove Device, then Remove.
HomePro Outlet
Join instructions
- Select the Start Z-Wave Inclusion button.
- Tap the button on the front of the module once to include it.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Tap the button on the front of the module once to exclude it.
Factory reset instructions
- Factory reset is unavailable for this device. Instead, perform a general exclusion.
Homeseer HomeSeer Fan Controller
Join instructions
1. Select Start Z-Wave Inclusion button.
2. Tap the paddle of your new HomeSeer switch to begin the inclusion process. This will take a few moments to complete.
Exclude instructions
1. Select Start Z-Wave Exclusion button.
2. Tap the paddle of your new HomeSeer switch to begin the Exclusion process. This will take a few moments to complete.
Factory reset instructions
(1) Turn switch on by tapping the top of the paddle once.
(2) Quickly ap top of the paddle 3 times.
(3) Quickly tap bottom of paddle 3 times.
(4) If the LED turns off then on again, switch is reset. If not, repeat manual rest.
Homeseer HomeSeer Indicator Light Sensor
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press the Z-Wave network button on the front of the unit once.
- Wait for the inclusion process to end and the device is successfully included. This may take some time.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the Z-Wave network button on the front of the unit once.
- Wait for the exclusion process to end and the device is successfully excluded. This may take some time.
Factory reset instructions
- Factory reset is unavailable for this device. Instead, perform a general exclusion.
Homeseer HomeSeer Perimeter Water Sensor
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press the Z-Wave network button on the front of the unit once.
- Wait for the inclusion process to end and the device is successfully included. This may take some time.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the Z-Wave network button on the front of the unit once.
- Wait for the exclusion process to end and the device is successfully excluded. This may take some time.
Factory reset instructions
- Factory reset is unavailable for this device. Instead, perform a general exclusion.
Homeseer Leak Sensor
Join instructions
- Select the Start Z-Wave Inclusion button.
- Click the Z-Wave button inside the sensor body once.
- Wait for the inclusion process to end and the device is successfully included.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Triple-click the Z-Wave button inside the sensor body.
- Wait for the exclusion process to end and the device is successfully excluded.
Factory reset instructions
- Press and hold the Z-Wave button for 20 seconds. Release the button once the LED stops flashing and glows solidly.
Homeseer Wall Dimmer
Join instructions
- Select the Start Z-Wave Inclusion button.
- Tap the paddle of the dimmer to begin the inclusion process.
- Wait for the inclusion process to end and the device is successfully included.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Tap the paddle of the dimmer to begin the exclusion process.
- Wait for the exclusion process to end and the device is successfully excluded.
Factory reset instructions
- Turn dimmer on by tapping the top of the paddle once.
- Quickly tap the top of the paddle 3 times.
- If the light turns off and then on again, the dimmer is reset. If not, repeat manual reset.
Homeseer Wall Switch
Join instructions
- Select the Start Z-Wave Inclusion button.
- Tap the paddle of the dimmer to begin the inclusion process.
- Wait for the inclusion process to end and the device is successfully included.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Tap the paddle of the dimmer to begin the exclusion process.
- Wait for the exclusion process to end and the device is successfully excluded.
Factory reset instructions
- Turn dimmer on by tapping the top of the paddle once.
- Quickly tap the top of the paddle 3 times.
- If the light turns off and then on again, the dimmer is reset. If not, repeat manual reset.
Homeseer ZWave Plus Door/Window Sensor
Join instructions
- Select the Start Z-Wave Inclusion button.
- Triple-click the Z-Wave button inside the sensor body and wait for the process to finish.
- If successful, the sensor body LED will flash briefly and then stay on for 3 seconds.
- If unsuccessful, the LED with flash briefly and then turn off. If this happens, repeat the inclusion process.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Triple-click the Z-Wave button inside the sensor body.
- If successful, the LED will turn off within 1 second.
- If unsuccessful, the LED with flash for 5 seconds. If this happens, repeat the exclusion process.
Factory reset instructions
- Press and hold the Z-Wave button inside the sensor body for 20 seconds, the LED will stay on until the button is released.
Honeywell T6 Pro Z-Wave Thermostat
Join instructions
- To include the thermostat, go to the thermostat Menu, then Z-Wave Setup. and touch Select.
- Select the Start Z-Wave Inclusion button.
- If the inclusion procedure is successful, INCLUDED, the node ID, and the Z-Wave connected status icon appear on the screen. If the procedure fails, then FAILED TO INCLUDE will appear on the screen.
- NOTE: • Before adding the thermostat to a Z-Wave network, check that it does not already belong to one. If the thermostat is included in Z-Wave network, it offers to Exclude. If the thermostat is excluded from Z-Wave network, it offers to include. You can also check the status by viewing the Node ID located in the thermostat MENU/ DEVICE INFO. An excluded thermostat should show zero for the Node ID (000).
- The T6 Pro Z-Wave thermostat works in the optional Z-Wave battery mode or normal power mode based on its power source. The Z-Wave power mode can only be changed when thermostat is NOT included in Z-Wave network. You can check the power mode in the thermostat menu under MENU/DEVICE INFO. • If 24 VAC power source is not used or available, the thermostat must be powered by batteries. The thermostat will operate in LSS mode (power-save, sleep mode) to help conserve battery life after it has been included in a Z-Wave network. The Z-Wave radio supports beaming. It allows other devices in the network to wake up the Z-Wave thermostat, accept commands, and then go back to sleep.
- If you need the thermostat to operate AOS mode (always listening mode) to act as signal repeater and to increase network reliability, you need to power the thermostat by 24 VAC.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- To exclude the thermostat, go to the thermostat Menu, then Z-Wave Setup. and touch Select.
Factory reset instructions
- Press and hold the Menu button for 5 seconds to access the Advanced Menu.
- Touch the left < or right > arrow keys to go through the options in the advanced menu.
- Choose Reset.
IKEA SYMFONISK Sound Remote
Join instructions
- Select the Start Zigbee Pairing button.
- Remove the battery cover from the bottom of the remote and hold the button for 10 seconds.
- Save the device and without deleting it from the hub, repeat steps 1 and 2 above.
- The hub will report that it found the previously paired device.
- NOTE: If you do not pair a second time with the device already in the Hubitat Elevation™ database, the remote may not work properly.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Remove the battery cover from the bottom of the remote and hold the button for 10 seconds to factory reset.
- Wait for at least 10 seconds after reset is complete before attempting to pair the remote.
IKEA TRÅDFRI Bulb E26
Join instructions
- Select the Start Zigbee Pairing button.
- Cycle power 6 times. The bulb will begin to dim and finally flash 1 time to confirm pairing was successful.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Cycle power 6 times. The bulb will begin to dim and finally flash 1 time to indicate that it has been successfully reset.
- Wait for at least 10 seconds after reset is complete before attempting to pair the bulb.
IKEA TRÅDFRI Outlet
Join instructions
- Select the Start Zigbee Pairing button.
- Using a straightened paperclip, insert it into the small hole on the left side of the outlet next to the LED.
- Press and hold the paperclip in the hole for 2-4 seconds (you will feel the paperclip depressing a tiny button inside the outlet).
- The LED will pulse slowly when pairing and will be steady when pairing has been successfully completed.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Using a straightened paperclip, insert it into the small hole on the left side of the outlet next to the LED.
- Press and hold the paperclip in the hole for at least 5 seconds (you will feel the paperclip depressing a tiny button inside the outlet).
- The LED will pulse quickly and then pulse slowly when you release the internal button.
- Wait for at least 10 seconds after reset is complete before attempting to pair the device.
IKEA TRÅDFRI Signal Repeater
Join instructions
- Select the Start Zigbee Pairing button.
- Using a straightened paperclip, insert it into the small hole at the end of the repeater next to the USB port.
- Press and hold the paperclip in the hole for 2-4 seconds (you will feel the paperclip depressing a tiny button inside the repeater).
- The LED will pulse slowly when pairing and will be steady when pairing has been successfully completed.
- The signal repeater will pair as Device. No driver will be assigned and it is not necessary to have one since this device only repeats Zigbee radio signals.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Using a straightened paperclip, insert it into the small hole at the end of the repeater next to the USB port.
- Press and hold the paperclip in the hole for at least 5 seconds (you will feel the paperclip depressing a tiny button inside the repeater).
- An LED will pulse quickly and then pulse slowly when you release the internal button.
- Wait for at least 10 seconds after reset is complete before attempting to pair the device.
Innr Smart Plug
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Innr Smart Spot Colour GU10
Join instructions
- Select the Start Zigbee Pairing button.
- Cycle power 6 times.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Cycle power 6 times.
Innr Zigbee outlet - UK version
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Inovelli On/Off Switch S2
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press the configure button 3 times. The LED bar will flash Blue.
- If the switch was included successfully, the LED bar will turn Green. If the inclusion process was not successful, the LED bar will turn Red.
- You can check the Z-Wave range by holding the configure button for 5-10 seconds. A Red bar indicates the switch is not in range of the controller or a signal repeater. Green indicates a good signal.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the configure button 3 times.
Factory reset instructions
- Select the Start Z-Wave Exclusion button.
- Hold down the configure button for 20 seconds.
Inovelli Outlet
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press in and release the button on the switch 3-5 times within 3 seconds to include it.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press in and release the button on the switch 3-5 times within 3 seconds to exclude it.
Factory reset instructions
- Press and hold the top button for at least 3 seconds while you plug the outlet into a receptacle.
Inovelli Smart Dimmer
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press the Top button on the switch 6 times within 2 seconds to include it.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the Top button on the switch 6 times within 2 seconds to exclude it.
Factory reset instructions
- Hold the UP button for 5 seconds when powered on.
Inovelli Smart Scene Dimmer
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press the Top button on the switch 6 times within 2 seconds to include it.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the Top button on the switch 6 times within 2 seconds to exclude it.
Factory reset instructions
- Hold the UP button for 5 seconds when powered on.
Inovelli Smart Scene Switch
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press the Top button on the switch 6 times within 2 seconds to include it.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the Top button on the switch 6 times within 2 seconds to exclude it.
Factory reset instructions
- Hold the UP button for 5 seconds when powered on.
Inovelli Smart Scene Switch S2
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press the configure button 3 times. The LED bar will flash Blue.
- If the switch was included successfully, the LED bar will turn Green. If the inclusion process was not successful, the LED bar will turn Red.
- You can check the Z-Wave range by holding the configure button for 5-10 seconds. A Red bar indicates the switch is not in range of the controller or a signal repeater. Green indicates a good signal.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the configure button 3 times.
Factory reset instructions
- Select the Start Z-Wave Exclusion button.
- Hold down the configure button for 20 seconds.
Inovelli Smart Switch
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press the Top button on the switch 6 times within 2 seconds to include it.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the Top button on the switch 6 times within 2 seconds to exclude it.
Factory reset instructions
- Hold the UP button for 5 seconds when powered on.
Inovelli Switch
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press the Top button on the switch 6 times within 2 seconds to include it.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the Top button on the switch 6 times within 2 seconds to exclude it.
Factory reset instructions
- Hold the UP button for 5 seconds when powered on.
Inovelli Switch Module
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press the center button 5 times within 1 second to include it.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the center button 5 times within 1 second to exclude it.
Factory reset instructions
- Factory reset is unavailable for this device. Instead, perform a general exclusion.
Iris Garage Door Opener
Join instructions
- Select the Start Z-Wave Inclusion button.
- Ensure your Iris Garage Door Controller is plugged in, and the tilt sensor battery is active/working.
- Press the Link (Z-Wave) button once located on the left of the Iris Garage Door Controller.
- When your device triple beeps, it has been successfully included.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Once the controller is ready to exclude your device, press the Link (Z-Wave) button once located on the left side of the device.
- The garage door controller should give a short beep immediately followed by a long beep to indicate successful exclusion.
Factory reset instructions
- Unplug your device and wait 10 seconds.
- Restore power to the device.
- Press the Link (Z-Wave) button on the left side of the device 5 times within 10 seconds to reset your device.
Iris Smart Water Sensor
Join instructions
- Select the Start Zigbee Pairing button.
- Remove the battery and wait 10 seconds.
- Re-insert the battery
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Remove the cover from the sensor, then remove the battery for at least 10 seconds.
- Press and hold the reset button while reinserting the battery.
- Hold for an additional 2 seconds and release.
- A successful reset will be indicated by a flashing blue light on your sensor
Iris V2 Button
Join instructions
- Select the Start Zigbee Pairing button.
- At this point, a blue light should be flashing on the button's top. If you don't see this, take the battery back out and try again.
- NOTES: The + side of the battery should be facing the bottom of the button when you insert the tray. At this point, a blue light should be flashing on the button's top. If you don't see this, take the battery back out and try again.
- The LED can be dim, if you're in a well lighted area this light could be difficult to see.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Remove the battery. Wait 10 seconds then re-insert battery.
- Within 10 seconds after re-inserting battery, press the button 8 times. The light will very dimly flash solid blue, than flash blue (even more faintly).
- NOTES: The + side of the battery should be facing the bottom of the button when you insert the tray. At this point, a blue light should be flashing on the button's top. If you don't see this, take the battery back out and try again.
- The LED can be dim, if you're in a well lighted area this light could be difficult to see.
Iris V2 Door/Window Sensor
Join instructions
- Select the Start Zigbee Pairing button.
- Remove battery. Wait 10 seconds then re-insert battery.
- Wait for the pairing process to end and the device is successfully paired.
- After pairing test your Iris Contact Sensor is working by opening and closing the door or window it's set up on (The LED should flash green when opened/closed).
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Slide the battery cover off, remove the battery and wait 10 seconds.
- Using a paper clip, press and hold the reset button completely down while reinserting the battery.
- Hold the reset button for an additional 2 seconds and release. The contact sensor should begin flashing blue.
- NOTE: The reset button is a small black button above the battery.
Iris V2 Keypad
Join instructions
- Select the Start Zigbee Pairing button.
- Remove the battery. Wait 10 seconds then re-insert battery.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Remove the battery and wait 10 seconds.
- Press and hold the tamper switch while inserting one battery. Hold tamper switch for 2 seconds after the battery is installed. The tamper switch is the little flat plastic tab located on the back where the mounting bracket connects to the device, it is above the battery compartment.
- Note: The factory reset process puts the security keypad back into pairing mode.
- Upon a proper reset the top right icon will be flashing green on your keypad.
- You may now insert the 2nd battery.
Iris V2 Motion Sensor
Join instructions
- Select the Start Zigbee Pairing button.
- Remove the battery for 10 seconds and re-insert.
- Replace the battery cover. The sensor's blue LED will flash while searching for the hub.
- Once paired the LED will stop flashing.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Remove the battery and wait 10 seconds
- Press and hold the reset button on the left side of the device as you reinsert the battery.
- Hold for an additional 2 seconds and release.
- Note: The reset button is a small white button located on the side of the motion sensor.
- Upon a successful reset your device will now be flashing blue, indicating it's ready to pair.
Iris V2 Outlet
Join instructions
- Select the Start Zigbee Pairing button.
- Insert your smart plug into any wall outlet. Your smart plug should be flashing Blue, that means it's in pairing mode.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Remove the Smart Plug from the outlet and wait 10 seconds.
- Press and hold the small white button on the front of the plug.
- While holding the button, insert the Smart Plug back into the outlet.
- As soon as the LED on the front of the plug lights up, release the button.
- If the reset was successful the blue LED on the front of the smart plug will be flashing. This means your smart plug is now ready to pair.
Iris V2 Smart Fob
Join instructions
- Select the Start Zigbee Pairing button.
- Insert the battery so the plus sign is facing you. Put the cover on and twist tighten with a coin.
- The Smart Fob's LED will flash blue while searching for the hub.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Twist open the battery cover on the back of the Smart Fob.
- Remove the battery and wait 10 seconds
- Reinstall the battery with the positive side facing you.
- Once the battery is installed, push any of the four buttons 8 times in a row, once per second.
- Confirm that the fob has been reset by checking that the fob's background light is flashing blue. If it does not do this, check the battery and retry from step 2.
Iris V3 Contact Sensor
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Iris V3 Keypad
Join instructions
- Select the Start Zigbee Pairing button.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Remove only 1 AA battery and wait 10 seconds.
- Re-insert the battery while holding down the reset button on the left side of the keypad and release when the status light flashes red once.
- A flashing blue light indicates the device is reset and ready to pair again.
Iris V3 Motion Sensor
Join instructions
- Select the Start Zigbee Pairing button.
- Remove the battery and wait 10 seconds.
- Re-insert the battery while holding down the reset button on the left side and release when the status light turns red.
- A flashing blue light indicates the device is ready to pair.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Remove the battery and wait 10 seconds.
- Re-insert the battery while holding down the reset button on the left side and release when the status light turns red.
- A flashing blue light indicates the device is ready to pair.
Iris V1 (AlertMe.com) Smart Plug
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Iris V1 (AlertMe.com) V1 Button
Join instructions
- Select the Start Zigbee Pairing button.
- With the smart button, squeeze the two sides together by the ridges and gently pull them apart to reveal the battery compartment.
- Remove and re-insert the battery. When the smart button begins looking for your hub, the light around the button will flash green.
- NOTE: The LED can be dim, if you're in a well lighted area this light could be difficult to see.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Squeeze the two sides of the smart button together by the ridges and gently pull them apart to reveal the battery compartment.
- Remove the battery for at least 10 seconds. Reinsert the battery.
- Within 10 seconds of reinserting the battery press the reset button next to the battery 8 times in a row, once per second.
- Upon a successful reset, the smart button will flash green indicating the device is now ready to pair.
- NOTE: The green light can be dim, if you're in a well lighted area this light could be difficult to see.
- If your button does not flash green check your battery, then retry from step 2.
Iris V1 (AlertMe.com) V1 Care Pendant
Join instructions
- Select the Start Zigbee Pairing button.
- Insert the supplied access tool into the small opening at the top of the pendant. Gently pry open the case to reveal the battery compartment.
- Insert the battery in the correct orientation. The pendant will light up and start flashing as it begins searching for your hub.
- NOTE: The LED can be dim, if you're in a well lighted area this light could be difficult to see.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Insert the supplied access tool into the small opening at the top of the key fob. Gently pry open the case to reveal the battery compartment.
- Remove the battery for at least 10 seconds. Reinsert the battery.
- Within 10 seconds of reinserting the battery, press either button 8 times in a row, once per second. The lights on the pendant should begin to flash.
- NOTE: The LED can be dim, if you're in a well lighted area this light could be difficult to see.
Iris V1 (AlertMe.com) V1 Door/Window Sensor
Join instructions
- Select the Start Zigbee Pairing button.
- On the large piece, remove the back by squeezing the semi-circles on either side.
- The sensor's LED will flash while searching for the hub.
- NOTE: The LED can be dim, if you're in a well lighted area this light could be difficult to see.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Squeeze the sides and pop open the sensor to reveal the battery, remove the battery and wait 10 seconds.
- Reinsert the battery and immediately press the white reset button 8 times.
- Your Iris Contact Sensor should now be flashing green indicating it's ready to pair.
- NOTE: The LED can be dim, if you're in a well lighted area this light could be difficult to see.
Iris V1 (AlertMe.com) V1 Keyfob
Join instructions
- Select the Start Zigbee Pairing button.
- Insert the supplied access tool into the small opening at the top of the key fob. Gently pry open the case to reveal the battery compartment.
- Insert the battery in the correct orientation. The fob will light up and start flashing as it begins searching for your hub.
- NOTE: The LED can be dim, if you're in a well lighted area this light could be difficult to see.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Insert the supplied access tool into the small opening at the top of the key fob. Gently pry open the case to reveal the battery compartment.
- Remove the battery for at least 10 seconds. Reinsert the battery.
- Within 10 seconds of reinserting the battery, press either button 8 times in a row, once per second. The lights on the key fob should begin to flash.
- NOTE: The LED can be dim, if you're in a well lighted area this light could be difficult to see.
Iris V1 (AlertMe.com) V1 Motion Sensor
Join instructions
- Select the Start Zigbee Pairing button.
- On the large piece, remove the back by squeezing the raised edges on both sides.
- Insert the battery. The sensor's LED will flash while searching for the hub.
- NOTE: The LED can be dim, if you're in a well lighted area this light could be difficult to see.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Squeeze the raised edges on the sides of the motion sensor to take it apart to expose the battery.
- Remove the battery for at least 10 seconds. Reinsert the battery.
- As soon as the battery is reinserted, press the reset button 8 times in a row, once per second. The lights on the top right corner of the motion sensor should begin to flash. (You may have to make a shadow over the device to see the flashing light). Once the light is flashing you're ready to pair.
- NOTE: The LED can be dim, if you're in a well lighted area this light could be difficult to see.
Iris V1 (AlertMe.com) V1 Smart Plug
Join instructions
- Select the Start Zigbee Pairing button.
- Insert the Smart Plug into any wall outlet.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Remove the Smart Plug from the receptacle.
- Press and hold the button on the front for 15 seconds.
- Insert the Smart Plug back into the receptacle.
- Immediately press the button on the front of the Smart Plug 8 times, allowing 1 second between each press.
KEEN Home Smart Vent
Join instructions
- Select the Start Zigbee Pairing button.
- Remove the battery cartridge and reinsert it to bring the vent online.
- Press the black button on the back inside of the Smart Vent battery compartment 5 times.
- This should force the vent into join-mode once again.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Press the black button on the back inside of the Smart Vent battery compartment 5 times.
- You will know that the Smart Vent has been properly reset when the LED starts double flashing green.
Kwikset 10-Button Deadbolt
Join instructions
- Select the Start Zigbee Pairing button.
- Press the A button 4 times.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Remove battery pack.
- Press and HOLD the Program button while reinserting the battery pack. Keep holding the button for 30 seconds until the lock beeps and the status LED flashes red.
- Press the Program button once more. The status LED will flash green and red several times.
Kwikset 10-Button Touch Deadbolt
Join instructions
- Select the Start Zigbee Pairing button.
- Press the A button 4 times.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Remove battery pack.
- Press and HOLD the Program button while reinserting the battery pack. Keep holding the button for 30 seconds until the lock beeps and the status LED flashes red.
- Press the Program button once more. The status LED will flash green and red several times.
Kwikset 5-Button Deadbolt
Join instructions
- Select the Start Zigbee Pairing button.
- Press the A button 4 times.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Remove battery pack.
- Press and HOLD the Program button while reinserting the battery pack. Keep holding the button for 30 seconds until the lock beeps and the status LED flashes red.
- Press the Program button once more. The status LED will flash green and red several times.
Kwikset 5-Button Lever
Join instructions
- Select the Start Zigbee Pairing button.
- Press the A button 4 times.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Remove battery pack.
- Press and HOLD the Program button while reinserting the battery pack. Keep holding the button for 30 seconds until the lock beeps and the status LED flashes red.
- Press the Program button once more. The status LED will flash green and red several times.
Kwikset 910/912/914 Lock
Join instructions
- Hold the interior assembly a maximum of 12" (305 mm) from your Hubitat Elevation hub.
- Select the Start Z-Wave Inclusion button.
- Press button A on the lock 1 time to include it. The controller and lock must remain stationary for a total of 60 seconds during the inclusion process.
- Wait for the inclusion process to end and the device is successfully included.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press button A on the lock 1 time to exclude it. The controller and lock must remain stationary for a total of 60 seconds during the exclusion process.
- Wait for the exclusion process to end and the device is successfully excluded.
Factory reset instructions
- Remove the battery pack
- Press and HOLD the Program button while reinserting the battery pack. Keep holding the button for 30 seconds until the lock beeps and the status LED flashes red.
- Press the Program button once more. When the LED flashes green and you hear 1 beep, the lock has been reset.
- Perform the door handing process again.
- Press and hold the Lock button while installing battery pack.
- Hold button until the latch bolt starts moving on its own. If the latch bolt retract and extend on its own when the battery pack was installed, then the handing process was successful.
- If the latch bolt does not retract and extend on its own, remove the battery pack and wait 15 seconds, before attempting the handing process again.
Kwikset Smartcode Lock
Join instructions
- Select the Start Zigbee Pairing button.
- Press the A button 4 times.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Remove battery pack.
- Press and HOLD the Program button while reinserting the battery pack. Keep holding the button for 30 seconds until the lock beeps and the status LED flashes red.
- Press the Program button once more. The status LED will flash green and red several times.
Kwikset Touchscreen Deadbolt
Join instructions
- Select the Start Zigbee Pairing button.
- Press the A button 4 times.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Remove battery pack.
- Press and HOLD the Program button while reinserting the battery pack. Keep holding the button for 30 seconds until the lock beeps and the status LED flashes red.
- Press the Program button once more. The status LED will flash green and red several times.
Leaksmart Water Sensor
Join instructions
- Select the Start Zigbee Pairing button.
- Press the black button in the battery compartment once.
- When paring is successful the sensors light will blink slowly five times and you will hear three beeps.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Press and hold the black button for 15 seconds.
- Remove and replace the batteries.
- The sensor should beep indicating a successful reset.
Leaksmart Water Valve
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Leviton In-Wall Dimmer
Join instructions
- Select the Start Zigbee Pairing button.
- Power up the dimmer.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Press and hold the top paddle for 14 seconds.
- After 14 seconds the LED will flash red/amber.
- Release the paddle .
Leviton In-Wall Switch
Join instructions
- Select the Start Zigbee Pairing button.
- Power up the switch.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Press and hold the top paddle for 14 seconds.
- After 14 seconds the LED will flash red/amber.
- Release the paddle .
Leviton Plug-in Appliance Module
Join instructions
- Enter programming mode by holding the control button for 7 seconds until the locator LED flashes amber.
- Select the Start Z-Wave Inclusion button.
- Tap the control button 1 time and the locator LED will quickly flash green.
- Upon successful inclusion the LED will turn off and then flash green 3 times.
- If inclusion fails, the LED will flash red 3 times.
- Wait for the inclusion process to end and the device is successfully included.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Enter programming mode by holding the control button for 7 seconds until the locator LED flashes amber.
- Tap the locator button 1 time and the locator LED will quickly flash green.
- Wait for the exclusion process to end and the device is successfully excluded.
Factory reset instructions
- Hold the control button for a total of 7 seconds and the locator LED flashes amber.
- Following the first 7 seconds, the locator LED will flash quickly, alternating between red and amber after 14 seconds.
- Release the top paddle to complete the reset process.
Leviton Plug-in Dimmer
Join instructions
- Select the Start Zigbee Pairing button.
- Plug in the dimmer.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Press and hold the button for 14 seconds.
- After 14 seconds the LED will flash red/amber.
- Release the button.
Leviton Plug-in Outlet
Join instructions
- Select the Start Zigbee Pairing button.
- Plug in the outlet.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Press and hold the button for 14 seconds.
- After 14 seconds the LED will flash red/amber.
- Release the button.
Leviton Scene controller
Factory reset instructions
- On the 4-Scene controller, press and hold buttons 1 and 3.
- Wait approximately 5 seconds until the LED turns amber and then solid red.
- Release the buttons and the 4-Scene controller will be reset.
NOTE: Factory reset does not exclude the device from any previous networks it has joined. The exclusion process must still be performed separately.
Leviton Smart Dimmer
Join instructions
- Enter programming mode by holding the control button for 7 seconds until the locator LED flashes amber.
- Select the Start Z-Wave Inclusion button.
- Tap the locator button 1 time and the locator LED will quickly flash green.
- Upon successful inclusion the LED will turn off and then flash green 3 times.
- If inclusion fails, the LED will flash red 3 times.
- Wait for the inclusion process to end and the device is successfully included.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Enter programming mode by holding the control button for 7 seconds until the locator LED flashes amber.
- Tap the locator button 1 time and the locator LED will quickly flash green.
- Wait for the exclusion process to end and the device is successfully excluded.
Factory reset instructions
- Hold the top paddle button for a total of 14 seconds.
- Following the first 7 seconds, the LED will turn amber.
- The locator LED will flash quickly, alternating between red and amber after 14 seconds.
- Release the top paddle to complete the reset process.
Leviton Switch
Join instructions
- Hold the top paddle for 7 seconds (The locator LED will flash amber).
- Tap the top paddle and the Locator LED will quickly flash green.
- Select the Start Zigbee Pairing button.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Hold the top paddle for 14 seconds (after the first 7 seconds the LED will turn amber).
- The Locator LED will alternate flashing red and amber after 14 seconds.
- Release the top paddle to complete the factory reset.
Life360 Life360 App
Join instructions
See Life360 Connector documentation page.
Exclude instructions
See Life360 Connector documentation page.
Factory reset instructions
See Life360 Connector documentation page.
LIFX 4-Gang Switch
Join instructions
- Use LIFX smartphone app to set up the bulb on the local network.
- Test device functionality using app.
- Click Install App button below to install LIFX integration.
- Add device in LIFX Integration App, if it is not shown immediately hit refresh.
LIFX A19 Bulb
Join instructions
- Use LIFX smartphone app to set up the bulb on the local network.
- Test device functionality using app.
- Click Install App button below to install LIFX integration.
- Add device in LIFX Integration App, if it is not shown immediately hit refresh.
LIFX BR30 Bulb
Join instructions
- Use LIFX smartphone app to set up the bulb on the local network.
- Test device functionality using app.
- Click Install App button below to install LIFX integration.
- Add device in LIFX Integration App, if it is not shown immediately hit refresh.
LIFX Candle White to Warm
Join instructions
- Use LIFX smartphone app to set up the bulb on the local network.
- Test device functionality using app.
- Click Install App button below to install LIFX integration.
- Add device in LIFX Integration App, if it is not shown immediately hit refresh.
LIFX Color bulb
Join instructions
- Use LIFX smartphone app to set up the bulb on the local network.
- Test device functionality using app.
- Click Install App button below to install LIFX integration.
- Add device in LIFX Integration App, if it is not shown immediately hit refresh.
LIFX CT Bulb
Join instructions
- Use LIFX smartphone app to set up the bulb on the local network.
- Test device functionality using app.
- Click Install App button below to install LIFX integration.
- Add device in LIFX Integration App, if it is not shown immediately hit refresh.
LIFX Mini Color Bulb
Join instructions
- Use LIFX smartphone app to set up the bulb on the local network.
- Test device functionality using app.
- Click Install App button below to install LIFX integration.
- Add device in LIFX Integration App, if it is not shown immediately hit refresh.
LIFX Mini Day Dusk Bulb
Join instructions
- Use LIFX smartphone app to set up the bulb on the local network.
- Test device functionality using app.
- Click Install App button below to install Wiz integration.
- Add device in LIFX Integration App, if it is not shown immediately hit refresh.
LIFX Mini White Bulb
Join instructions
- Use LIFX smartphone app to set up the bulb on the local network.
- Test device functionality using app.
- Click Install App button below to install LIFX integration.
- Add device in LIFX Integration App, if it is not shown immediately hit refresh.
LIFX Strip
Join instructions
- Use LIFX smartphone app to set up the bulb on the local network.
- Test device functionality using app.
- Click Install App button below to install LIFX integration.
- Add device in LIFX Integration App, if it is not shown immediately hit refresh.
LIFX Switch
Join instructions
- Use LIFX smartphone app to set up the bulb on the local network.
- Test device functionality using app.
- Click Install App button below to install LIFX integration.
- Add device in LIFX Integration App, if it is not shown immediately hit refresh.
LIFX White Bulb
Join instructions
- Use LIFX smartphone app to set up the bulb on the local network.
- Test device functionality using app.
- Click Install App button below to install LIFX integration.
- Add device in LIFX Integration App, if it is not shown immediately hit refresh.
Linear Contact Sensor
Join instructions
- Unscrew the screw on the rear cover and slide the rear cover down.
- Insert a CR123A battery into the battery compartment and LED will start to flash slowly, which means the sensor has not yet performed inclusion with the controller.
- Select the Start Z-Wave Inclusion button.
- Upon successful inclusion the LED will stop flashing.
- If the LED does not stop flashing and is not discovered by your hub, relocate the WADWAZ-1 to within 100 feet (line of sight) of a Z-Wave repeater or your hub and restart Z-Wave Inclusion.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the program switch of WADWAZ-1 for 1 second and release. The LED light will flash continuously when the sensor has been successfully excluded.
Factory reset instructions
- Factory reset is unavailable for this device. Instead, perform a general exclusion.
Linear Motion Sensor
Join instructions
- Select the Start Z-Wave Inclusion button.
- Depress the Tamper switch for 1 second then release. The LED on the sensor will begin flashing.
- Wait for the inclusion process to end. The LED on the sensor will stop flashing when the device is successfully included.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the Tamper switch for 1 second then release it to exclude the device.
- Wait for the exclusion process to end. The LED light will flash continuously when the sensor is successfully excluded.
Factory reset instructions
- Factory reset is unavailable for this device. Instead, perform a general exclusion.
Linear Siren
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press the siren/strobe Program/Tamper switch for 1 second then release. The LED on the sensor will begin flashing.
- Wait for the exclusion process to end. The LED on the sensor will stop flashing when the device is successfully included.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the siren/strobe Program/Tamper switch for 1 second then release to exclude the device form the Z-wave network.
- Wait for the exclusion process to end. The LED light will flash continuously when the sensor is successfully excluded.
Factory reset instructions
- Factory reset is unavailable for this device. Instead, perform a general exclusion.
Linkind Dimmable White Bulb
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Linkind Door/Window Sensor
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Linkind Motion Sensor
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Linkind Smart Plug
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Linkind Tunable White Bulb
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Lutron Aurora Controller
Join instructions
- Select the Start Zigbee Pairing button.
- Quickly press the center button on the Aurora 2 times to begin pairing.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Quickly press the center button 3 times and hold on the third press for approximately 6 seconds until the LED flashes.
- Once the LED is flashing quickly tap the button 3 times again.
- The LED will flash rapidly to indicate the device has been successfully reset to factory defaults.
Lutron Caséta Fan Control
Join instructions
See the online Lutron Integrator Documentation here.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
- Perform a factory reset on the device.
Factory reset instructions
- Tap the tapswitch 3 times on a control. DO NOT release after the third tap.
- Keep the tapswitch pressed on the third tap (for approximately 3 seconds) until the LEDs on the dimmer start to scroll up and down quickly, or the LED on the switch flashes quickly
- Release the tapswitch and immediately tap it 3 times again.
- The LEDs on the dimmer will scroll up and down slowly and then the LED on the switch will flash slowly, indicating it has now been returned to Factory Default Settings.
Lutron Caséta In-Wall Smart Dimmer Switch
Join instructions
See the online Lutron Integrator Documentation here.
Exclude instructions
- From the device's details page, select Remove Device, then Remove
- Perform a factory reset on the device
Factory reset instructions
- Tap the "On" button quickly 3 times, holding on the last press.
- Continue to hold the "On" button until the light begins to flash quickly.
- Release the button, then immediately tap the button 3 more times.
- All paired Pico remote controls are removed and all settings are returned to factory default.
Lutron Caséta In-Wall Smart Dimmer Switch for ELV
Join instructions
See the online Lutron Integrator Documentation here.
Lutron Caséta Lamp Dimming Smart Plug
Join instructions
See the online Lutron Integrator Documentation here.
Lutron Caséta Outdoor Smart Plug
Join instructions
See the online Lutron Integrator Documentation here.
Lutron Caséta Serena Shades
Join instructions
See the online Lutron Integrator Documentation here.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
- Perform a factory reset on the device.
Factory reset instructions
- Tap the shade button quickly 3 times, and hold the shade button after the third tap until the shade button LED flashs Green rapidly.
- Immediately tap the shade button quickly 3 more times, until the shade button LED flashes Green rapidly, then flashes Red/Green 3 times, and turns off.
- The Serena shade has now been returned to Factory Default Settings.
Lutron Caséta Smart Switch For Light or Fan Control
Join instructions
See the online Lutron Integrator Documentation here.
Exclude instructions
- From the device's details page, select Remove Device, then Remove
- Perform a factory reset on the device
Factory reset instructions
- Tap the "On" button quickly 3 times, holding on the last press.
- Continue to hold the "On" button until the light begins to flash quickly.
- Release the button, then immediately tap the button 3 more times.
- All paired Pico remote controls are removed and all settings are returned to factory default.
Lutron Caséta SmartBridge Pro
Join instructions
- Click the Install App button below to install the Lutron Bridge Integrator.
- Follow the online instructions here, beginning at step "Gathering required information" to complete the installation.
Factory reset instructions
Network Reset
- First, press and hold the black button on the back of your Smart Bridge for 20 seconds.
Factory Reset
- Quickly tap the button 3 times and hold. DO NOT release after the third tap.
- Continue to hold the Add button for a few seconds. The LEDs will begin to flash slowly (approximately once per second).
- Release the button and quickly tap the button 3 times. The LEDs will flash quickly and then will turn off. (*Note* The time between release and the second triple tap must be less than half a second, thus must be performed very quickly)
- The Lutron Smart Bridge Pro has now been returned to Factory Default Settings.
- NOTE: Lutron does not recommend factory resetting a Smart Bridge Pro unless advised by a member of the Lutron technical support team.
Lutron Lutron fan control (no level)
Join instructions
See the online Lutron Integrator Documentation here.
This is an alternate driver to the Lutron Shade driver that's installed via the Lutron Integration.
Lutron Lutron Shade (no level or switch commands)
Join instructions
See the online Lutron Integrator Documentation here.
This is an alternate driver to the Lutron Shade driver that's installed via the Lutron Integration.
Lutron Pico Remote
Join instructions
See the online Lutron Integrator Documentation here.
Exclude instructions
- From the device's details page, select Remove Device, then Remove
- Perform a factory reset on the device
Factory reset instructions
- Tap the "On" button quickly 3 times, holding on the last press.
- Continue to hold the "On" button until the light begins to flash quickly.
- Release the button, then immediately tap the button 3 more times.
- All paired Pico remote controls are removed and all settings are returned to factory default.
Lutron RadioRA2 Dimmer
Join instructions
See the online Lutron Integrator Documentation here.
Exclude instructions
- From the device's details page, select Remove Device, then Remove
- Perform a factory reset on the device
Factory reset instructions
- Tap the "On" button quickly 3 times, holding on the last press.
- Continue to hold the "On" button until the light begins to flash quickly.
- Release the button, then immediately tap the button 3 more times.
- All paired Pico remote controls are removed and all settings are returned to factory default.
Lutron RadioRA2 HVAC Controller
Join instructions
See the online Lutron Integrator Documentation here.
Lutron RadioRA2 Keypad
Join instructions
See the online Lutron Integrator Documentation here.
Exclude instructions
- From the device's details page, select Remove Device, then Remove
- Perform a factory reset on the device
Factory reset instructions
- Tap the "On" button quickly 3 times, holding on the last press.
- Continue to hold the "On" button until the light begins to flash quickly.
- Release the button, then immediately tap the button 3 more times.
- The RA2 keypad has now been returned to Factory Default Settings.
Lutron RadioRA2 Main Repeater
Join instructions
- Click the Install App button below to install the Lutron Bridge Integrator.
- Follow the online instructions here, beginning at step "Create a New Caséta/RA2 Integration" to complete the installation.
Exclude instructions
- From the device's details page, select Remove Device, then Remove
- Perform a factory reset on the device
Factory reset instructions
- Tap the Test button on a Main Repeater 3 times. DO NOT release the button after the third tap.
- Keep the Test button pressed on the third tap until all the LEDs start to flash red slowly (approximately 3 seconds).
- Release the Test button and immediately tap 3 times again. All the LEDs will flash Red quickly.
- When the LEDs stop flashing, the Main Repeater has been returned to factory settings
Lutron RadioRA2 Motion/Occupancy Sensor
Join instructions
See the online Lutron Integrator Documentation here.
Exclude instructions
- From the device's details page, select Remove Device, then Remove
- Perform a factory reset on the device
Factory reset instructions
Radio Powr Savr™ Occupancy/Vacancy Ceiling Sensor – 1st Generation (LRF2-xCRB-)
- Quickly tap 3 times and hold the Test, Lights ON, or Lights OFF button on the Sensor. DO NOT release after third tap.
- Keep the button pressed after the third tap for a few seconds until the dome LED begins to flash slowly (approximately once per second).
- Release the button and tap it again 3 times until the dome LED on the Sensor flashes quickly. (*Note* The time between release and the second triple tap must be less than half a second, thus must be performed very quickly).
- The Sensor has now been returned to Factory Default Settings.
Radio Powr Savr™ Occupancy/Vacancy Ceiling Sensor – 2nd Generation (LRF2- xCR2B-)
- Quickly tap 3 times and hold the Test or Light button on the Sensor. DO NOT release after third tap.
- Keep the button pressed after the third tap for a few seconds until the dome LED begins to flash slowly (approximately once per second).
- Release the button and tap 3 times again until the dome LED on the Sensor flashes quickly. (*Note* The time between release and the second triple tap must be less than half a second, thus must be performed very quickly).
- The Sensor has now been returned to Factory Default Settings.
Radio Powr Savr™ Occupancy/Vacancy Wall-Mounted Sensor
- Quickly triple tap and hold the Sensor, Lights ON, or Lights OFF button on the Sensor. DO NOT release after third tap.
- Keep the button pressed after the third tap for a few seconds until the lens LED begins to flash slowly (approximately once per second).
- Release the button and tap it again 3 times until the lens LED on the Sensor flashes quickly. (*Note* The time between release and the second triple tap must be less than half a second, thus must be performed very quickly).
- The Sensor has now been returned to Factory Default Settings.
Lutron RadioRA2 Select Main Repeater
Join instructions
- Click the Install App button below to install the Lutron Bridge Integrator.
- Follow the online instructions here, beginning at step "Create a New Caséta/RA2 Integration" to complete the installation.
Lutron RadioRA2 Switch
Join instructions
See the online Lutron Integrator Documentation here.
Exclude instructions
- From the device's details page, select Remove Device, then Remove
- Perform a factory reset on the device
Factory reset instructions
- Tap the "On" button quickly 3 times, holding on the last press.
- Continue to hold the "On" button until the light begins to flash quickly.
- Release the button, then immediately tap the button 3 more times.
- All paired Pico remote controls are removed and all settings are returned to factory default.
Lutron RadioRA2 VCRX Visor Controller Receiver
Join instructions
See the online Lutron Integrator Documentation here.
Exclude instructions
- From the device's details page, select Remove Device, then Remove
- Perform a factory reset on the device.
Factory reset instructions
- Quickly tap 3 times and hold any button (except Learn) on the VCRX. DO NOT release after third tap.
- Keep the button pressed after the third tap for a few seconds until all the status LEDs start to flash slowly (approximately once per second).
- Release the button and tap 3 times again until all the status LEDs on the VCRX flash quickly. (*Note* The time between release and the second triple tap must be less than half a second, thus must be performed very quickly).
- The VCRX has now been returned to Factory Default Settings.
Lutron Sivoia QS Triathlon Shades
Join instructions
See the online Lutron Integrator Documentation here.
Exclude instructions
- From the device's details page, select Remove Device, then Remove
- Perform a factory reset on the device
Factory reset instructions
- Tap the shade button quickly 3 times, and hold the shade button after the third tap until the shade button LED flashs Green rapidly.
- Immediately tap the shade button quickly 3 more times, until the shade button LED flashes Green rapidly, then flashs Red/Green 3 times, and turns off.
- The Sivoia shade has now been returned to Factory Default Settings.
Lux Zigbee Thermostat
Join instructions
- KONOz is now ready to be configured for your heating and cooling system. The KONOz will guide you through the initial system configuration.
- After confirming your system settings, KONOzwill ask if you would like to connect to a Smart Hub. Select “SET” to establish a connection.
- Select the Start Zigbee Pairing button.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Access the installation settings by going to the main menu and selecting the gear icon.
- You will see “IS” on the screen and will be prompted to select “yes” or “no”.
- Select “yes” to access the installation settings.
- Rotate the knob to view settings and press the knob to confirm.
- Once in the installer settings, rotate the knob to 99.
- Press the knob to confirm, then press and hold the knob for 3 seconds.
Marantz Audio Video Receiver
Join instructions
- Click the Install Device button.
- Enter the AVR's IP address in the Denon IP preference field in the driver details, click Save Preferences.
- Turn the AVR on, then select each of the available AVR inputs on the physical device, these will appear in the driver details Current States.
- Any inpu'ts display name can be changed by selecting the desired input and clicking the Edit Current Input Name command after adding the new name in the New name field.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
MCOHome Dimmer Switch
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press 3 times on the "+" button to add the device. If successful, the green LED flashes 4 times.
- Note: If an external switch is wired to the dimmer, you may also toggle that 3 times to include the device.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press 3 times on the "-" button to exclude the device. If successful, the green LED flashes 4 times.
- Note: If an external switch is wired to the dimmer, you may also toggle that 3 times to exclude the device.
Factory reset instructions
- Press any button 10 times or perform a Z-Wave Exclusion, then cut-off the main power.
- The factory settings will be restored.
MHCOZY Relay
Join instructions
- Select the Start Zigbee Pairing button.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Press and hold any of the manual switch buttons for 15 seconds.
Minoston Mini Smart Plug Dimmer
Join instructions
Once the controller is ready to add your device, press the Manual/Program button on the smart plug 3 times quickly. The blue LED will blink quickly.
Auto-add mode: LED will blink within 30 seconds after first plugged in.
Exclude instructions
Once the controller is ready to remove your device, press the Manual/Program button on the smart plug 3 times quickly.
Factory reset instructions
Click the Manual/Program button 2 times quickly then hold for at least 10 seconds .
Mode Lighting eDIN+ Network Processor Module
Join instructions
- Click the Install Device button.
- Enter the Network Module's IP address in the IP Address preference field in the driver details, click Save Preferences.
Monoprice 6 Zone Audio Controller
Join instructions
- Click the Install Device button.
- Enter the Zone Controller IP address in the IP preference field in the driver details.
- Enter the Telnet port used by the device, for the Multi Zone Pre Amp the port is 8080, for the Multi Zone Amp, the port depends on the serial to IP adapter being used, click Save Preferences.
- Any input's display name can be changed by selecting the desired input and clicking the Edit Current Input Name command after adding the new name in the New name field.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Monoprice Contact Sensor
Join instructions
- Select the Start Z-Wave Inclusion button.
- Rapidly press the Z button 3 times to include the device.
- Wait for the inclusion process to end and the device is successfully included.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Rapidly press the Z button 3 times to exclude the device.
- Wait for the exclusion process to end and the device is successfully excluded.
Factory reset instructions
- To reset the sensor, press and hold the Z button for about 20 seconds.
- The LED will change from steadily illuminated to flashing then back to steadily illuminated, indicating that the reset operation was successful.
Monoprice Outlet
Join instructions
- Select the Start Z-Wave Inclusion button.
- If the plug-in has not already been included into a Z-Wave network, the LED indicator will flash rapidly. Otherwise, the plug-in has already been included and must first be excluded before it can join the Hubitat Elevation™ Z-Wave network.
- Wait for the inclusion process to end and the device is successfully included.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Click the Z button 3 times to exclude the device.
- Wait for the exclusion process to end and the device is successfully excluded.
Factory reset instructions
- Press and hold the Z button for 20 seconds and then release it. Your sensor will now be reset to its original settings.
Monoprice Plugin Dimmer
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press and hold the program button on the front for about 1 second to include the device.
- Wait for the inclusion process to end and the device is successfully included.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press and hold the program button on the front for about 1 second to exclude the device.
- Wait for the exclusion process to end and the device is successfully excluded.
Factory reset instructions
- Factory reset is unavailable for this device. Instead, perform a general exclusion.
Monoprice Z-Wave Plugin On/Off
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press and hold the program button on the front for about 1 second to include the device.
- Wait for the inclusion process to end and the device is successfully included.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press and hold the program button on the front for about 1 second to exclude the device.
- Wait for the exclusion process to end and the device is successfully excluded.
Factory reset instructions
- Factory reset is unavailable for this device. Instead, perform a general exclusion.
Monoprice Z-Wave Plus Door/Window Sensor
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press and hold the program button on the front for about 1 second to include the device.
- The LED will stop flashing and glow steadily to indicate the device has been successfully included.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press and hold the program button on the front for about 1 second to exclude the device.
- Wait for the exclusion process to end and the device is successfully excluded.
Factory reset instructions
- Factory reset is unavailable for this device. Instead, perform a general exclusion.
Monoprice Z-Wave Plus PIR Motion Detector With Temperature Sensor
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press and hold the program button on the front for about 1 second to include the device.
- The LED will stop flashing and glow steady to indicate successful inclusion.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press and hold the program button on the front for about 1 second to exclude the device.
- Wait for the exclusion process to end and the device is successfully excluded.
Factory reset instructions
- Factory reset is unavailable for this device. Instead, perform a general exclusion.
Monoprice Z-Wave Plus PIR Multi Sensor
Join instructions
- Select the Start Z-Wave Inclusion button.
- Momentarily press the Program button.
- The LED should flash 5 times indicating the sensor is ready for inclusion.
- Wait for the inclusion process to end and the device is successfully included.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the program button. The LED will flash, indicating the device has been successfully excluded.
Factory reset instructions
- Factory reset is unavailable for this device. Instead, perform a general exclusion.
Monoprice Z-Wave Plus Recessed Door/Window Sensor
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press the Z button on your sensor. The LED will turn solid for 2 seconds and then turn off to indicate successful inclusion.
- If inclusion was unsuccessful, the LED will continue to flash if you tap its button.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the Z button on your sensor. If your device has been successfully excluded the LED will start to flash for a short time.
- If exclusion was unsuccessful, the LED will return to its last state.
Factory reset instructions
- Press and hold the Z button for 20 seconds and then release it. Your sensor will now be reset to its original settings
Monoprice Z-Wave Plus Smart Plug and Repeater with 2 USB ports
Join instructions
- Select the Start Z-Wave Inclusion button.
- Rapidly press the Z button 3 times to include the device.
Testing the Smart Plug Z-Wave connection
You can test the connectivity of the Z-Wave network connection, with the RGB LED being used to indicate the connection quality.
To begin testing, press and hold the Z button for 6-9 seconds, releasing the button when the RGB LED illuminates violet.
Note: The smart plug must be included into a Z-Wave network to test the network connection. You can abort the test at any time by pressing the Z button.
- Flashing Green: The RGB LED will flash Green while the smart plug is attempting to establish a connection with the main controller.
- Solid Green: The RGB LED will illuminate Green for about 2 seconds to indicate that direct communications are stable.
- Flashing Orange: The RGB LED will flash Orange while the smart plug is attempting to establish a connection with the main controller with intermediate radio transmitting power.
- Solid Orange: The RGB LED will illuminate Orange for about 2 seconds to indicate that the communication quality is moderate.
- Solid Red: The RGB LED will illuminate Red for about 2 seconds to indicate that they communications attempt has failed.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Rapidly press the Z button 3 times to exclude the device.
- The RGB LED will flash orange while the smart plug is being excluded.
- When successfully excluded the RGB LED will illuminate orange steadily for about 2 seconds.
Factory reset instructions
- Ensure that the smart plug is inserted into an AC outlet.
- Press and hold the Z button on the smart plug for more than 20 seconds.
- The LED indicator will illuminate yellow steadily for about 2 seconds.
NanoLeaf Aurora Light Panels
Join instructions
- Use the NanoLeaf Smarter Series app from your mobile device to setup your light panels on the WiFi network.
- Click the Install Device button.
- In the Preferences field of the driver, enter the IP address of your Nanoleaf panel, click Save Preferences.
- One your NanoLeaf panel, press the pairing button.
- In the NanoLeaf Aurora driver, press the Get Auth Token button.
- Test your panel for proper operation.
NanoLeaf Canvas Light Panels
Join instructions
- Use the NanoLeaf Smarter Series app from your mobile device to setup your light panels on the WiFi network.
- Click the Install Device button.
- In the Preferences field of the driver, enter the IP address of your Nanoleaf panel, click Save Preferences.
- One your NanoLeaf panel, press the pairing button.
- In the NanoLeaf Aurora driver, press the Get Auth Token button.
- Test your panel for proper operation.
NEEO NEEO Remote
Join instructions
- Click the Install Device button.
- Enter the Brain's Wi-Fi IP address in the NEEO ip address field in the driver details, click Save Preferences.
NEO Door Sensor
Join instructions
- Power up the device.
- Select the Start Z-Wave Inclusion button.
- Press and hold the button for 5 seconds until the white led is on, then release the button before the led turns off.
- Wait for the inclusion process to end and the device is successfully included.
Exclude instructions
- Power up the device.
- Select the Start Z-Wave Exclusion button.
- Press and hold the button for 5 seconds until the white led light is on, then release the button before led turns off.
- Wait for the exclusion process to end and the device is successfully excluded.
Factory reset instructions
- Power up the device.
- Press and hold the button for 10 seconds until pink led light is on, then release the button before the led turns off.
NEO NEO Coolcam Door/Window Sensor
Join instructions
- Select the Start Z-Wave Inclusion button.
- Quickly click the code button 3 times, the LED light will flash 5 times.
- Wait for the inclusion process to end and the device is successfully included.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Quickly click the code button 3 times.
- The LED light will flash 5 times to indicate the device has been successfully excluded.
Factory reset instructions
- Remove the cover of contact sensor main body.
- Make sure the sensor is connected to a power source.
- Press and hold the reset button for 10 seconds, the LED light will flash red once.
- Release the button.
NEO NEO Coolcam Door/Window Sensor
Join instructions
- Select the Start Z-Wave Inclusion button.
- Quickly click the code button 3 times, the LED light will flash 5 times.
- Wait for the inclusion process to end and the device is successfully included.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Quickly click the code button 3 times.
- The LED light will flash 5 times to indicate the device has been successfully excluded.
Factory reset instructions
- Remove the cover of contact sensor main body.
- Make sure the sensor is connected to a power source.
- Press and hold the reset button for 10 seconds, the LED light will flash red once.
- Release the button.
NEO NEO Coolcam Motion Sensor
Join instructions
- Select the Start Z-Wave Inclusion button.
- Quickly click the Code button 3 times, the LED light will flash 5 times.
- Wait for the inclusion process to end and the device is successfully included.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Quickly click the Code button 3 times, the LED light will flash 5 times and the sensor will be excluded from the Z-Wave network.
Factory reset instructions
- Remove the sensor’s cover.
- Make sure the sensor is connected to a power source.
- Press the Code button for 10 seconds, the LED will flash red once.
- Release the Code button.
- NOTE: When the PIR is being restored to factory settings, please make sure a power source is connected.
NEO NEO Coolcam Power Plug
Join instructions
- Select the Start Z-Wave Inclusion button.
- Quickly click the Code button 3 times, the LED light will flash 5 times.
- Wait for the inclusion process to end and the device is successfully included.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Quickly click the code button 3 times, the LED light will flash for 5 times and the device will be excluded from the Z-Wave network.
Factory reset instructions
- Press and hold the Code button on the front of the outlet for 10 seconds.
- When the LED flashes, release the button.
- When the outlet has been reset, the LED will flash on and off 5 times within a 2 second period.
NEO NEO Coolcam Remote Control
Join instructions
- Select the Start Z-Wave Inclusion button.
- Quickly click the red SOS alarm button 3 times.
- Wait for the inclusion process to end and the device is successfully included.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Quickly click the red SOS alarm button 3 times and the device will be excluded from the Z-Wave network.
Factory reset instructions
- Press and hold the Code button for 10 seconds.
- Release the Code button.
- Note: Do not power off during factory reset.
NodOn Octan Remote
Join instructions
- Select the Start Z-Wave Inclusion button.
- Simultaneously push on the "O" and "+" for 1 second.
- The LED glows in pink to confirm the selection.
- Push on the "O" within 10 seconds.
- The LED flashes in pink to confirm your choice and then flashes in green to confirm the procedure.
- Wait for the inclusion process to end and the device is successfully included.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Simultaneously push on the "O" and "+" for 1 second.
- The LED glows in pink to confirm the selection.
- Push on the "O" within 10 seconds.
- The LED flashes in pink to confirm your choice and then flashes in green to confirm the procedure.
- Wait for the exclusion process to end and the device is successfully excluded.
Factory reset instructions
- A simultaneous long press (1 second) on "O" and "–" will perform a factory reset.
- The LED will flash red and green to validate the device has been reset.
NodOn Soft Remote
Join instructions
- Select the Start Z-Wave Inclusion button.
- Simultaneously push on the "O" and "+" for 1 second.
- The LED glows in pink to confirm the selection.
- Push on "O" within 10 seconds.
- The LED flashes in pink to confirm your choice and then flashes in green to confirm the procedure.
- Wait for the inclusion process to end and the device is successfully included.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Simultaneously push on the "O" and "+" for 1 second.
- The LED glows in pink to confirm the selection.
- Push on the "O" within 10 seconds.
- The LED flashes in pink to confirm your choice and then flashes in green to confirm the procedure.
- Wait for the exclusion process to end and the device is successfully excluded.
Factory reset instructions
- A simultaneous long press (1 second) on "O" and "–" will perform a factory reset.
- The LED will flash red and green to validate the device has been reset.
Nue 1 Gang Light Switch
Join instructions
- Select the Start Zigbee Pairing button.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Remove the device cover.
- Press and hold the button for 10 seconds.
Nue 2 Gang Light Switch
Join instructions
- Select the Start Zigbee Pairing button.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Remove the device cover.
- press and hold the button for 10 seconds.
Nue 3 Gang Light Switch
Join instructions
- Select the Start Zigbee Pairing button.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Remove the device cover.
- press and hold the button for 10 seconds.
Nue 4 Gang Light Switch
Join instructions
- Select the Start Zigbee Pairing button.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Remove the device cover.
- press and hold the button for 10 seconds.
Nue RGBW Strip Controller
Join instructions
- Select the Start Zigbee Pairing button.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Press and hold the reset until the LED begins flashing red.
Nue Zigbee 3.0 Light Controller
Join instructions
- Select the Start Zigbee Pairing button.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Press and hold the reset button until the LED begins blinking red.
Nue Zigbee 3.0 Smart Socket Plug
Join instructions
- Select the Start Zigbee Pairing button.
Factory reset instructions
- Press and hold the power button for 10 seconds.
- The LED will blink red.
Nue Zigbee Dimmer
Join instructions
- Select the Start Zigbee Pairing button.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Remove the device cover.
- Press and hold the button for 10 seconds.
Nue Zigbee Dimmer
Join instructions
- Select the Start Zigbee Pairing button.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Remove the device cover.
- Press and hold the button for 10 seconds.
Nue Zigbee Fan Contoller
Join instructions
- Select the Start Zigbee Pairing button.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Remove the device cover.
- Press and hold the button for 10 seconds.
Nue Zigbee Scene Contoller
Join instructions
- Select the Start Zigbee Pairing button.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Remove the device cover.
- Press and hold the button for 10 seconds.
Nue Zigbee Switch
Join instructions
- Select the Start Zigbee Pairing button.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Remove the device cover.
- press and hold the button for 10 seconds.
NYCE Ceiling Motion Sensor
Join instructions
- Select the Start Zigbee Pairing button.
- Remove the Mounting Plate by rotating the Housing counter-clockwise.
- Inside the battery compartment is a small button on the side of the circuit board.
- Note: The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.
- Press the button 4 times to pair the device.
- The LED will flash in the following sequences:
- Yellow - red - yellow flashes indicate it is searching for a network to join.
- Yellow - green - yellow flashes indicate the device is being configured.
- 3 green flashes indicate the device has successfully paired.
- 3 red flashes indicate the devices failed to pair. If this happens, ensure a factory reset has been performed and repeat the process from step 4.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Remove the Mounting Plate by rotating the Housing counter-clockwise.
- Inside the battery compartment is a small button on the side of the circuit board.
- Note: The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.
- Pressing the button 10 times will leave the network and reset the device to factory defaults.
- The LED will flash red 3 times to indicate is has left the network (If joined), and it will flash green 5 times to indicate defaults have been restored.
NYCE Curtain Motion Sensor
Join instructions
- Select the Start Zigbee Pairing button.
- To open the battery cover, use a flathead screwdriver in the recessed slot at the bottom of the sensor housing.
- Inside the battery compartment at the top, is a small button.
- Note: The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.
- Press the button 4 times to pair the device.
- The LED will flash in the following sequences:
- Yellow - red - yellow flashes indicate it is searching for a network to join.
- Yellow - green - yellow flashes indicate the device is being configured.
- 3 green flashes indicate the device has successfully joined the network.
- 3 red flashes indicate the devices failed to join the network. If this happens, ensure a factory reset has been performed and repeat the process from step 4.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- To open the battery cover, use a flathead screwdriver in the recessed slot at the bottom of the sensor housing.
- Inside the battery compartment at the top, is a small button.
- Note: The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.
- Pressing the button 10 times will leave the network and reset the device to factory defaults.
- The LED will flash red 3 times to indicate is has left the network (If joined), and it will flash green 5 times to indicate defaults have been restored.
NYCE Door/Window Sensor
Join instructions
- Select the Start Zigbee Pairing button.
- Slide open the Door/Window Sensor’s top housing.
- Inside the battery compartment is a small button.
- Note: The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.
- Press the button 4 times to pair the device.
- The LED will flash in the following sequences:
- Yellow - red - yellow flashes indicate it is searching for a network to join.
- Yellow - green - yellow flashes indicate the device is being configured.
- 3 green flashes indicate the device has successfully paired.
- 3 red flashes indicate the device has failed to pair. If this happens, perform a factory reset and repeat the process from step 4.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Slide open the Door/Window Sensor’s top housing.
- Inside the battery compartment is a small button.
- Note: The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.
- Pressing the button 10 times will remove the device from the network and reset the device to factory defaults.
- The LED will flash red 3 times to indicate is has left the network (If joined), and it will flash green 5 times to indicate defaults have been restored.
NYCE Garage Door (Tilt) Sensor
Join instructions
- Select the Start Zigbee Pairing button.
- Slide open the Garage Door (Tilt) Sensor’s top housing.
- Inside the battery compartment is a small button.
- Note: The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.
- Press the button 4 times to pair the device.
- The LED will flash in the following sequences:
- Yellow - red - yellow flashes indicate it is searching for a network to join.
- Yellow - green - yellow flashes indicate the device is being configured.
- 3 green flashes indicate the device has successfully paired.
- 3 red flashes indicate the device failed to pair. If this happens, perform a factory reset and repeat the process from step 4.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Slide open the Garage Door (Tilt) Sensor’s top housing.
- Inside the battery compartment is a small button.
- Note: The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.
- Pressing the button 10 times will leave the network and reset the device to factory defaults.
- The LED will flash red 3 times to indicate is has left the network (If joined), and it will flash green 5 times to indicate defaults have been restored.
NYCE Motion Sensor
Join instructions
- Select the Start Zigbee Pairing button.
- To open the battery cover, use a flathead screwdriver in the recessed slot at the bottom of the sensor housing.
- Inside the battery compartment at the top, is a small button.
- Note: The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.
- Press the button 4 times to pair the device.
- The LED will flash in the following sequences:
- Yellow - red - yellow flashes indicate it is searching for a network to join.
- Yellow - green - yellow flashes indicate the device is being configured.
- 3 green flashes indicate the device has successfully paired.
- 3 red flashes indicate the devices failed to pair. If this happens, ensure a factory reset has been performed and repeat the process from step 4.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- To open the battery cover, use a flathead screwdriver in the recessed slot at the bottom of the sensor housing.
- Inside the battery compartment at the top, is a small button.
- Note: The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.
- Pressing the button 10 times will leave the network and reset the device to factory defaults.
- The LED will flash red 3 times to indicate is has left the network (If joined), and it will flash green 5 times to indicate defaults have been restored.
Onkyo Audio Video Receiver
Join instructions
- Click the Install Device button.
- Enter the AVR's IP address in the Onkyo IP preference field in the driver details, click Save Preferences.
- Turn the AVR on, then select each of the available AVR inputs on the physical device, these will appear in the driver details Current States.
- Any input's display name can be changed by selecting the desired input and clicking the Edit Current Input Name command after adding the new name in the New name field.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Orbit 12-Station Sprinkler Controller
Join instructions
- Select the Start Zigbee Pairing button.
- Ensure the controller is connected to power.
- Turn the dial to AUTO.
- When the controller is first connected to power, it will automatically attempt to connect.
- NOTE: If pairing is not successful after 10 minutes, the controller will stop trying to pair. To re-enter pairing mode, push the 'SYNC' button 5 times in rapid succession
- The wireless icon will flash until the controller is paired. Once paired, the wireless icon will remain solid, and the words SMART MODE will appear on the screen.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Ensure the controller is connected to power.
- Press the SYNC button 5 times in rapid secession. The device will try to re-connect again, so you will need to let it time out or hold the SYNC button for 5 seconds to cancel re-pairing.
Orbit Smart Hose Faucet Timer
Join instructions
- Select the Start Zigbee Pairing button.
- Slide out the battery tray on the back of the timer.
- Insert two AA alkaline batteries and re-insert the tray.
- NOTE: Firmly replace the battery tray to ensure water resistance and increase battery life. You will know the battery tray is fully inserted if it does not pull out easily.
- Turn the dial to AUTO.
- When batteries are inserted, the timer will automatically attempt to connect and the wireless icon on screen will begin to flash.
- NOTE: The timer will remain in pairing mode for 10 minutes or until paired. If pairing is not successful after 10 minutes, the timer will stop trying to pair. To enter pairing mode again press the RESET button 5 times in rapid secession.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Insert two AA alkaline batteries and re-insert the tray.
- Press the RESET button 5 times in rapid secession.
Orvibo Motion Sensor
Join instructions
- Remove the cover by rotating it counter-clockwise
- Select the Start Zigbee Pairing button.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Hold down the reset button on the front of the motion sensor until the green light goes out.
- This will disconnect the sensor from the Zigbee network.
- Short-press the reset button and the green light will flash slowly.
- The sensor is now in pairing mode.
Osram Lightify Flex RGBW
Join instructions
- Select the Start Zigbee Pairing button.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Start with the Light Strip powered ON.
- Repeat 5 times - Unplug for 1 second and then plug in for 1 second
- On the fifth time plugging in the Light Strip, leave it plugged in
- After about 3 seconds, the Light Strip will flash rapidly 3 times to show a successful reset and ready for pairing.
Osram Lightify LED Classic B40 Tunable White 60W
Join instructions
- Select the Start Zigbee Pairing button.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Turn the light off.
- Turn the light on for three 3 seconds.
- Turn the light off.
- Repeat this cycle 5 times.
- Wait 10 seconds for the light to flash 3 times.
- Repeat these steps if the light does not flash 3 times.
Osram Lightify LED Flood BR30 Tunable White
Join instructions
- Select the Start Zigbee Pairing button.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Turn the light off.
- Turn the light on for three 3 seconds.
- Turn the light off.
- Repeat this cycle 5 times.
- Wait 10 seconds for the light to flash 3 times.
- Repeat these steps if the light does not flash 3 times.
Osram Lightify LED Recessed Kit RT 5/6 Tunable
Join instructions
- Select the Start Zigbee Pairing button.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Turn the light off.
- Turn the light on for three 3 seconds.
- Turn the light off.
- Repeat this cycle 5 times.
- Wait 10 seconds for the light to flash 3 times.
- Repeat these steps if the light does not flash 3 times.
Osram Lightify LED Tunable White 60W
Join instructions
- Select the Start Zigbee Pairing button.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Turn the light off.
- Turn the light on for three 3 seconds.
- Turn the light off.
- Repeat this cycle 5 times.
- Wait 10 seconds for the light to flash 3 times.
- Repeat these steps if the light does not flash 3 times.
Osram Smart Outdoor Plug
Join instructions
- Select the Start Zigbee Pairing button.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
Method 1
- Hold the button for 30 seconds.
- The outdoor plug will click 5 times.
- The outdoor plug is now reset and ready for pairing.
Method 2
- Turn the outdoor plug off.
- Turn the outdoor plug on for 5 seconds.
- Turn the outdoor plug off.
- Repeat this cycle 5 times.
- The outdoor plug is now reset and ready for pairing.
Osram Smart+ Classic E27 Multicolor
Join instructions
- Select the Start Zigbee Pairing button.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Turn the light off.
- Turn the light on for three 3 seconds
- Turn the light off.
- Repeat this cycle 5 times.
- Wait 10 seconds for the light to flash 3 times.
- Repeat these steps if the light does not flash 3 times.
PEQ Contact Sensor
Join instructions
- Select the Start Zigbee Pairing button.
- Slide the sensor off the mount and remove cover. Remove battery for 10 seconds and replace
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Slide the sensor off the mount, remove cover, and remove battery.
- While holding down the reset button, reinsert battery to factory reset the device.
PEQ Moisture Sensor
Join instructions
- Select the Start Zigbee Pairing button.
- Slide the sensor off the mount and remove cover. Remove battery for 10 seconds and replace
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Slide the sensor off the mount, remove cover, and remove battery.
- While holding down the reset button, reinsert battery to factory reset the device.
PEQ Motion Sensor
Join instructions
- Select the Start Zigbee Pairing button.
- Slide the sensor off the mount and remove cover. Remove battery for 10 seconds and replace
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Slide the sensor off the mount, remove cover, and remove battery.
- While holding down the reset button, reinsert battery to factory reset the device.
Philio Philio PST02
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press tamper key three times within 1.5 seconds
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press tamper key three times within 1.5 seconds
Factory reset instructions
1. Pressing tamper key four times within 1.5 seconds and do not release the tamper key on the 4th press, the LED lite will ON.
2. After 3 seconds the LED will turn OFF, after that within 2 seconds, release the tamper key. If successful, the LED will light ON one second.
Otherwise, the LED will flash once.
Philips Hue Bloom Lights
Join instructions
- Select the Start Zigbee Pairing button.
- Power on the light.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- You must use a Hue Dimmer to factory reset a Hue bulb, light fixture or LED strip that is not attached to a Hue bridge.
- Turn on the light to be reset.
- NOTE: ensure other bulbs within a few inches are unscrewed or unplugged or they may be reset too.
- Hold the remote within 4 inches of the light.
- Press and hold the 1st (On / I in some countries) and the and 4th (Off / O in some countries) buttons simultaneously for about 10 seconds, until the light starts flashing on and off.
- When the light stops flashing, it will remain ON at full brightness, and the green LED on the remote will flash, indicating the bulb has been factory reset.
Philips Hue Bridge
Join instructions
- Click the Install App button below to install the Hue Bridge Integration.
- Follow the online instructions beginning at step 4 here to complete setup.
Philips Hue Dimmer Switch
Join instructions
- Select the Start Zigbee Pairing button.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Turn the dimmer switch over and use a straightened paperclip to press the setup button on the back for 1 second.
Philips Hue Dimmer Switch V2
Join instructions
- Select the Start Zigbee Pairing button.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Turn the dimmer switch over and use a straightened paperclip to press the setup button on the back for 1 second.
Philips Hue Indoor Motion Sensor V2
Join instructions
- Select the Start Zigbee Pairing button.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- On the back of the motion sensor, press the setup button for 1 second.
Philips Hue Living Colors Lights
Join instructions
- Select the Start Zigbee Pairing button.
- Power on the light.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- You must use a Hue Dimmer to factory reset a Hue bulb, light fixture or LED strip that is not attached to a Hue bridge.
- Turn on the light on to be reset.
- NOTE: ensure other bulbs within a few inches are unscrewed or unplugged or they may be reset too.
- Hold the remote within 4 inches of the light.
- Press and hold the 1st (On / I in some countries) and the and 4th (Off / O in some countries) buttons simultaneously for about 10 seconds, until the light starts flashing on and off.
- When the light stops flashing, it will remain ON at full brightness, and the green LED on the remote will flash, indicating the bulb has been factory reset.
Philips Hue Lux
Join instructions
- Select the Start Zigbee Pairing button.
- Power on the light.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- You must use a Hue Dimmer to factory reset a Hue bulb, light fixture or LED strip that is not attached to a Hue bridge.
- Turn on the light on to be reset.
- NOTE: ensure other bulbs within a few inches are unscrewed or unplugged or they may be reset too.
- Hold the remote within 4 inches of the light.
- Press and hold the 1st (On / I in some countries) and the and 4th (Off / O in some countries) buttons simultaneously for about 10 seconds, until the light starts flashing on and off.
- When the light stops flashing, it will remain ON at full brightness, and the green LED on the remote will flash, indicating the bulb has been factory reset.
Philips Hue Motion Sensor
Join instructions
- Select the Start Zigbee Pairing button.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- On the back of the motion sensor, use a straightened paperclip to press the setup button for 1 second.
Philips Hue Outdoor Motion Sensor
Join instructions
- Select the Start Zigbee Pairing button.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- On the back of the motion sensor, use a straightened paperclip to press the setup button for 1 second.
Philips Hue Philips wall switch module
Join instructions
- Select the Start Zigbee Pairing button.
- Toggle input number 1
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Hold the reset button until LED turns red, then turns off.
Philips Hue Smart Button
Join instructions
- Select the Start Zigbee Pairing button.
- Press the button until the LED on the front of the button is flashing.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Turn the smart button over and remove the back cover. Use a straightened paperclip to press the setup button on the back for 5 seconds. An LED on the front of the sensor will flash once to confirm factory reset.
Philips Hue Smart Plug
Join instructions
- Select the Start Zigbee Pairing button.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Press the power button for 10 seconds.
Philips Hue Strip Lights
Join instructions
- Select the Start Zigbee Pairing button.
- Power on the light.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- You must use a Hue Dimmer to factory reset a Hue bulb, light fixture or LED strip that is not attached to a Hue bridge.
- Turn on the light on to be reset.
- NOTE: ensure other bulbs within a few inches are unscrewed or unplugged or they may be reset too.
- Hold the remote within 4 inches of the light.
- Press and hold the 1st (On / I in some countries) and the and 4th (Off / O in some countries) buttons simultaneously for about 10 seconds, until the light starts flashing on and off.
- When the light stops flashing, it will remain ON at full brightness, and the green LED on the remote will flash, indicating the bulb has been factory reset.
Philips Hue White Ambiance
Join instructions
- Select the Start Zigbee Pairing button.
- Power on the light.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- You must use a Hue Dimmer to factory reset a Hue bulb, light fixture or LED strip that is not attached to a Hue bridge.
- Turn on the light on to be reset.
- NOTE: ensure other bulbs within a few inches are unscrewed or unplugged or they may be reset too.
- Hold the remote within 4 inches of the light.
- Press and hold the 1st (On / I in some countries) and the and 4th (Off / O in some countries) buttons simultaneously for about 10 seconds, until the light starts flashing on and off.
- When the light stops flashing, it will remain ON at full brightness, and the green LED on the remote will flash, indicating the bulb has been factory reset.
Philips Hue White and Color Ambiance Bulb
Join instructions
- Select the Start Zigbee Pairing button.
- Power on the light.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- You must use a Hue Dimmer to factory reset a Hue bulb, light fixture or LED strip that is not attached to a Hue bridge.
- Turn on the light on to be reset.
- NOTE: ensure other bulbs within a few inches are unscrewed or unplugged or they may be reset too.
- Hold the remote within 4 inches of the light.
- Press and hold the 1st (On / I in some countries) and the and 4th (Off / O in some countries) buttons simultaneously for about 10 seconds, until the light starts flashing on and off.
- When the light stops flashing, it will remain ON at full brightness, and the green LED on the remote will flash, indicating the bulb has been factory reset.
Philips Hue White and Color Ambiance LightStrip
Join instructions
- Select the Start Zigbee Pairing button.
- Power on the light.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- You must use a Hue Dimmer to factory reset a Hue bulb, light fixture or LED strip that is not attached to a Hue bridge.
- Turn on the light on to be reset.
- NOTE: ensure other bulbs within a few inches are unscrewed or unplugged or they may be reset too.
- Hold the remote within 4 inches of the light.
- Press and hold the 1st (On / I in some countries) and the and 4th (Off / O in some countries) buttons simultaneously for about 10 seconds, until the light starts flashing on and off.
- When the light stops flashing, it will remain ON at full brightness, and the green LED on the remote will flash, indicating the bulb has been factory reset.
Philips Wiz Wi-Fi Wiz Connected Smart LED Light Bulb
Join instructions
- Use Wiz smartphone app to set up the bulb on the local network.
- Test bulb functionality using app.
- Click the Install App button below to install the Wiz integration.
- Enable Wiz integration if it is disabled.
- Click Start device discovery and wait. Integration app should find the bulb in 30 seconds or less.
Exclude instructions
Wiz integration finds all local Wiz compatible devices automatically. If a device is no longer on the network, remove it using Remove button at the bottom of device details page.
Philips Wiz Wi-Fi Wiz Wireless Connected Smart Plug
Join instructions
- Use Wiz smartphone app to set up the bulb on the local network.
- Test bulb functionality using app.
- Click the Install App button below to install the Wiz integration.
- Enable Wiz integration if it is disabled.
- Click Start device discovery and wait. Integration app should find the bulb in 30 seconds or less.
Exclude instructions
Wiz integration finds all local Wiz compatible devices automatically. If a device is no longer on the network, remove it using Remove button at the bottom of device details page.
Pioneer Audio Video Receiver
Join instructions
- Click the Install Device button.
- Enter the AVR's IP address in the Pioneer IP preference field in the driver details, click Save Preferences.
- Turn the AVR on, then select each of the available AVR inputs on the physical device, these will appear in the driver details Current States.
- Any input's display name can be changed by selecting the desired input and clicking the Edit Current Input Name command after adding the new name in the New name field.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Powely Thermostat
Join instructions
- Select the Start Z-Wave Inclusion button.
- To put your thermostat into inclusion mode, press and hold Mode for 5 seconds.
- CONNECT will scroll across the thermostat display once in inclusion mode.
- SUCCESS will scroll across the thermostat display once included, but FAIL will scroll across the thermostat display if inclusion is unsuccessful.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press and hold Mode for 5 seconds to initiate the Z-Wave exclusion process.
- DELETE will scroll across the thermostat display once in exclusion mode. If you need to cancel the exclusion process, press Mode.
- To complete exclusion, press either the up or down arrow.
- SUCCESS will scroll across the thermostat display once excluded.
Factory reset instructions
- To reset to factory defaults, turn the thermostat off by pressing Mode repeatedly until OFF scrolls across the display.
- Press and hold the down and up Setpoint arrows at the same time for 5 seconds.
- If successful, RESET will scroll across the display and the device will be restored to its default settings.
Qubino Flush 1 Relay
Join instructions
- Select the Start Z-Wave Inclusion button.
- Connect the device to the power supply (with the temperature sensor already connected*).
- Toggle the switch connected to the I1 terminal 3 times within 5 seconds. The device has to get On/Off signal 3 times, meaning pushing on the push button 3 times or 6 times flip of a switch.
- NOTE: If the device is powered by 24 V SELV supply, press and hold the S (Service) button between 2-6 seconds.
- NOTE: *If connecting the temperature sensor, switch off the power supply and make sure the device is excluded from your network BEFORE connecting the sensor.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Toggle the switch connected to the I1 terminal 3 times within 5 seconds.
- NOTE: If the device is powered by 24 V SELV supply, press and hold the S (Service) button between 2-6 seconds.
Factory reset instructions
- Connect the device to a power supply.
- Within the first 60 seconds the device is connected to the power supply, toggle the switch connected to the I1 terminal 5 times within 5 seconds (switch state 5 times).
- NOTE: If the device is powered by 24 V SELV supply, press and hold the S (Service) button for more than 6 seconds.
- NOTE: By resetting the device, all custom parameters previously set on the device will return to their default values, and the owner ID will be deleted.
Qubino Flush 1D Relay
Join instructions
- Select the Start Z-Wave Inclusion button.
- Connect the device to a power supply (with the temperature sensor already connected*).
- Toggle the switch connected to the I1 terminal 3 times within 5 seconds. The device has to get the On/Off signal 3 times, meaning push on the push button 3 times or flip of a switch 6 times.
- NOTE: If the device is powered by 24 V SELV supply, press and hold the S (Service) button between 2-6 seconds.
- NOTE: *If connecting the temperature sensor, switch off the power supply and make sure the device is excluded from your network BEFORE connecting the sensor
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Toggle the switch connected to the I1 terminal 3 times within 3 seconds.
- NOTE: If the device is powered by 24 V SELV supply, press and hold the S (Service) button between 2-6 seconds.
Factory reset instructions
- Connect the device to a power supply.
- Within the first 60 seconds the device is connected to the power supply, toggle the switch connected to the I1 terminal 5 times within 5 seconds (change the switch state 5 times).
- NOTE: If the device is powered by 24 V SELV supply, press and hold the S (Service) button for more than 6 seconds.
- NOTE: By resetting the device, all custom parameters previously set on the device will return to their default values, and the owner ID will be deleted.
Qubino Flush 2 Relay
Join instructions
- Select the Start Z-Wave Inclusion button.
- Connect the device to the power supply (with the temperature sensor already connected*).
- Toggle the switch connected to the I1 terminal 3 times within 3 seconds. The device has to get On/Off signal 3 times, meaning push on the push button 3 times or flip of a switch 6 times.
- NOTE: If the device is powered by 24 V SELV supply, press and hold the S (Service) button between 2-6 seconds.
- NOTE: *If connecting the temperature sensor, switch off the power supply and make sure the device is excluded from your network BEFORE connecting the sensor.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Toggle the switch connected to the I1 terminal 3 times within 3 seconds.
- NOTE: If the device is powered by 24 V SELV supply, press and hold the S (Service) button between 2-6 seconds.
Factory reset instructions
- Connect the device to a power supply.
- Within the first 60 seconds the device is connected to the power supply, toggle the switch connected to the I1 terminal 5 times within 5 seconds (change switch state 5 times).
- NOTE: If the device is powered by 24 V SELV supply, press and hold the S (Service) button for more than 6 seconds.
- NOTE: By resetting the device, all custom parameters previously set on the device will return to their default values, and the owner ID will be deleted.
Qubino Flush Dimmer
Join instructions
- Select the Start Z-Wave Inclusion button.
- Connect the device to a power supply (with the temperature sensor already connected*).
- Toggle the switch connected to the I1 terminal 3 times within 3 seconds. The device has to get On/Off signal 3 times, meaning push on the push button 3 times or flip of a switch 6 times.
- NOTE: If the device is powered by 24 V SELV supply, press and hold the S (Service) button between 2-6 seconds.
- NOTE: *If connecting the temperature sensor, switch off the power supply and make sure the device is excluded from your network BEFORE connecting the sensor.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Toggle the switch connected to the I1 terminal 3 times within 3 seconds.
- NOTE: If the device is powered by 24 V SELV supply, press and hold the S (Service) button between 2-6 seconds.
Factory reset instructions
- Connect the device to the power supply
- Within the first 60 seconds the device is connected to the power supply, toggle the switch connected to the I1 terminal 5 times within 3 seconds (5 times change switch state).
- If the device is powered by 24 V SELV supply, press and hold the S (Service) button for more than 6 seconds.
- NOTE: By resetting the device, all custom parameters previously set on the device will return to their default values, and the owner ID will be deleted.
Qubino Flush ON/OFF Thermostat
Join instructions
- Select the Start Z-Wave Inclusion button.
- Connect the device to a power supply (with the temperature sensor already connected*).
- Toggle the switch connected to the I1 terminal 3 times within 3 seconds. The device has to get On/Off signal 3 times, meaning push on the push button 3 times or flip of a switch 6 times.
- NOTE: If the device is powered by 24 V SELV supply, press and hold the S (Service) button between 2-6 seconds.
- NOTE: *If connecting the temperature sensor, switch off the power supply and make sure the device is excluded from your network BEFORE connecting the sensor.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Toggle the switch connected to the I1 terminal 3 times within 3 seconds.
- NOTE: If the device is powered by 24 V SELV supply, press and hold the S (Service) button between 2-6 seconds.
Factory reset instructions
- Connect the device to a power supply.
- Within the first 60 seconds the device is connected to the power supply, toggle the switch connected to the I1 terminal 5 times within 5 seconds (change switch state 5 times).
- NOTE: If the device is powered by 24 V SELV supply, press and hold the S (Service) button for more than 6 seconds.
- NOTE: By resetting the device, all custom parameters previously set on the device will return to their default values, and the owner ID will be deleted.
Qubino Flush Shutter
Join instructions
- Select the Start Z-Wave Inclusion button.
- Connect the device to a power supply (with the temperature sensor already connected*).
- Toggle the switch connected to the I1 terminal 3 times within 3 seconds. The device has to get On/Off signal 3 times, meaning push on the push button 3 times or flip of a switch 6 times.
- NOTE:If the device is powered by 24 V SELV supply, press and hold the S (Service) button between 2-6 seconds.
- NOTE: *If connecting the temperature sensor, switch off the power supply and make sure the device is excluded from your network BEFORE connecting the sensor.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Toggle the switch connected to the I1 terminal 3 times within 3 seconds
- NOTE: If the device is powered by 24 V SELV supply, press and hold the S (Service) button between 2-6 seconds.
Factory reset instructions
- Connect the device to a power supply
- Within the first 60 seconds the device is connected to the power supply, toggle the switch connected to the I1 terminal 5 times within 5 seconds (change switch state 5 times).
- NOTE: If the device is powered by 24 V SELV supply, press and hold the S (Service) button for more than 6 seconds.
- NOTE: By resetting the device, all custom parameters previously set on the device will return to their default values, and the owner ID will be deleted.
Qubino Flush Shutter DC
Join instructions
- Select the Start Z-Wave Inclusion button.
- Connect the device to a power supply (with the temperature sensor already connected*).
- Toggle the switch connected to the I1 terminal 3 times within 3 seconds. The device has to get On/Off signal 3 times, meaning push on the push button 3 times or flip of a switch 6 times.
- NOTE: If the device is powered by 24 V SELV supply, press and hold the S (Service) button between 2-6 seconds.
- NOTE: *If connecting the temperature sensor, switch off the power supply and make sure the device is excluded from your network BEFORE connecting the sensor.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Toggle the switch connected to the I1 terminal 3 times within 3 seconds
- If the device is powered by 24 V SELV supply, press and hold the S (Service) button between 2-6 seconds.
Factory reset instructions
- Connect the device to a power supply.
- Within the first 60 seconds the device is connected to the power supply, toggle the switch connected to the I1 terminal 5 times within 3 seconds (change switch state 5 times).
- NOTE: If the device is powered by 24 V SELV supply, press and hold the S (Service) button for more than 6 seconds.
- NOTE: By resetting the device, all custom parameters previously set on the device will return to their default values, and the owner ID will be deleted.
Qubino Mini Dimmer
Join instructions
- Select the Start Z-Wave Inclusion button.
- Connect the device to a power supply.
- Toggle the switch connected to the I1 terminal 3 times within 3 seconds (this procedure puts the device in LEARN MODE).
- NOTE: Inclusion with the switch connected to I1 terminal is not limited by time.
- Alternatively, press and hold the S (Service) button between 2-6 seconds if connected to 24-30VDC (to put the device in LEARN MODE).
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Connect the device to a power supply.
- Toggle the switch connected to the I1 terminal 3 times within 3 seconds (this procedure puts the device in LEARN MODE).
- NOTE: Exclusion with the switch connected to I1 terminal is not limited by time.
- Alternatively, press and hold the S (Service) button between 2-6 seconds if connected to 24-30VDC (to put the device in LEARN MODE).
Factory reset instructions
- Connect the device to a power supply.
- Within the first 60 seconds the device is connected to the power supply, toggle the switch connected to the I1 terminal 5 times within 3 seconds.
- Alternatively, press and hold the S (Service) button for at least 6 seconds if connected to 24-30VDC.
Quotra Quotra Wireless Smart Dimmer
Join instructions
- Select the Start Zigbee Pairing button.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Press and hold the power button for 10 seconds.
- Release when the LED slowly fades in and out (this will only happen for 3 seconds).
Radio CT100 Thermostat
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press/touch the MATE button on the MENU screen. A large r1 will be displayed.
- This will bring you to the network include screen. Confirm by touching MATE again to initiate the mating process. The MATE icon and the status indicator LEDs will flash.
- When a device has been successfully included, the LINK icon will appear under the radio tower.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press/touch the MATE button on the MENU screen. A large r1 will be displayed.
- This will bring you to the network include screen. Confirm by touching MATE again to initiate the mating process. The MATE icon and the status indicator LEDs will flash.
- When a device has successfully been excluded, the LINK icon will disappear under the radio tower.
Factory reset instructions
Preferred Method:
- The thermostat must be in OFF mode.
- Wait until the radio wave icons on the left side of the screen stop flashing then touch the screen once to turn on the back light and then hold the center of the screen for about 8 seconds until the thermostat beeps.
Alternate Method:
- Place the CT101 in the off position by pressing mode button until OFF is shown at the top left of the screen.
- Press the menu button.
- Press and hold the center of the screen for about 5 sec or until the screen changes, then release.
- You will see two arrows. First press the up arrow and wait for the count down.
- Now press the down arrow and again, wait for the count down.
- All parameter values will be restored to defaults and a message is sent to any radio module installed to instruct the module to restore its own default values.
- Press the house to get back to the main screen.
Radio CT101 Thermostat
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press/touch the MATE button on the MENU screen. A large r1 will be displayed.
- This will bring you to the network include screen. Confirm by touching MATE again to initiate the mating process. The MATE icon and the status indicator LEDs will flash.
- When a device has been successfully included, the LINK icon will appear under the radio tower.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press/touch the MATE button on the MENU screen. A large r1 will be displayed.
- This will bring you to the network include screen. Confirm by touching MATE again to initiate the mating process. The MATE icon and the status indicator LEDs will flash.
- When a device has been successfully excluded, the LINK icon will disappear under the radio tower.
Factory reset instructions
Preferred method:
- The thermostat must be in OFF mode.
- Wait until the radio wave icons on the left side of the screen stop flashing then touch the screen once to turn on the back light and then hold the center of the screen for about 8 seconds until the thermostat beeps.
Alternate Method:
- Place the CT101 in the off position by pressing mode button until OFF is shown at the top left of the screen.
- Press the menu button.
- Press and hold the center of the screen for about 5 sec or until the screen changes, then release.
- You will see two arrows. First press the up arrow and wait for the count down.
- Now press the down arrow and again, wait for the count down.
- All parameter values will be restored to defaults and a message is sent to any radio module installed to instruct the module to restore its own default values.
- Press the house to get back to the main screen.
Remotec ZFM-80 Relay / Fixture Switch
Join instructions
- Select the Start Z-Wave Inclusion button.
- Click once on the PROG button or external attached switch.
- Wait for the inclusion process to end and the device is successfully included.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Click once on the PROG button or external attached switch.
- Wait for the exclusion process to end and the device is successfully excluded.
Factory reset instructions
- Factory reset is unavailable for this device. Instead, perform a general exclusion.
Remotec ZRC-90 Button Controller
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press L & R buttons simultaneously until the LED lights up. The LED will keep flashing slowly.
- Press the program button. The LED will flash 1 time, then remain off if the device was successfully included.
- If the LED flashes 6 times rapidly, then remains off, the device has failed to be inclusion.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Click 1 time on the R button. The LED will continue flashing slowly.
- Press the program button. The LED will flash 1 time, then remain off if the device has been successfully excluded.
- If the LED flashes 6 times rapidly, then remains off, the device has failed exclusion.
- Perform a factory reset and repeat the above steps to exclude the device.
Factory reset instructions
- Press and keep holding the R button for a minimum of 10 seconds.
- Release the R button and then click 3 times on the same R button within 2 seconds.
RGBgenie 3 Scene Color Touch Panel and Dimmer
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
RGBgenie 3 Zone Color Touch Panel
Join instructions
- Select the Start Zigbee Pairing button.
- Press and hold the power button until the LED status indicator turns on.
- Immediately press the S1 button once to enable the Touch Panel to search for nearby networks. The LED indicator will flash once every second.
- Wait for the pairing process to end and the device is successfully paired.
- Quickly press any button and the LED indicator should flash once indicating device was successfully paired.
- If the LED indicator does not respond, the Touch Panel is not paired with a network.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Press and hold down the power button on the Touch Panel until the LED indicator turns on.
- Immediately press the power button 5 times.
- The LED indicator will flash 3 times quickly to indicate successful removal from the network and is now reset to factory default.
RGBgenie 4 Channel Dimming Controller
Join instructions
- Select the Start Zigbee Pairing button.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Press the program button quickly 5 times, or if the unit is not accessible, power the device off and on quickly 5 times.
- The LED will flash quickly and then stay in a slow rhythmic breathing pattern to indicate a successful reset.
RGBgenie 4 Zone 2 Scene Remote
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
RGBgenie 5 Zone Remote and Dimmer
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
RGBgenie Color Micro Remote with single scene recall
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
RGBgenie Color Remote
Join instructions
- Select the Start Zigbee Pairing button.
- Press and hold the power button until the LED status indicator turns on.
- Immediately press the S1 button once to enable the Touch Panel to search for nearby networks. The LED indicator will flash once every second.
- Wait for the pairing process to end and the device is successfully paired.
- Quickly press any button and the LED indicator should flash once indicating device was successfully paired.
- If the LED indicator does not respond, the Touch Panel is not paired with a network.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Press and hold down the power button on the Touch Panel until the LED indicator turns on.
- Immediately press the power button 5 times.
- The LED indicator will flash 3 times quickly to indicate successful removal from the network and is now reset to factory default.
RGBgenie Micro Controller and Lamp Module
Join instructions
- Power on the micro controller.
- Select the Start Z-Wave Inclusion button.
- Press the Reset button 3 times quickly.
- Wait for the inclusion process to end and the device is successfully included.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the Reset button 3 times quickly.
- Wait for the exclusion process to end and the device is successfully excluded.
Factory reset instructions
- Press and hold down the Reset button for over 10 seconds.
RGBgenie RGBW Color Controller
Join instructions
- Select the Start Zigbee Pairing button.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Press the program button quickly 5 times, or if the unit is not accessible, power the device off and on quickly 5 times.
- The LED will flash 3 times quickly to indicate successful removal from the network and is now reset to factory default.
RGBgenie RGBW Color Controller
Join instructions
- Power on the LED dimmer
- Select the Start Z-Wave Inclusion button.
- Wait for the inclusion process to end and the device is successfully included.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the Inclusion/Exclusion button 3 times.
- The LED dimmer will be set to Exclusion mode and the connected LED light will flash quickly for 6 seconds.
- The LED light will stay ON solid for 3 seconds to indicate successful exclusion.
Factory reset instructions
- Press and hold down the Inclusion/Exclusion button for over 10 seconds.
- The connected LED light will stays ON solid for 3 seconds to indicate successful factory reset.
- Release the Inclusion/Exclusion button and all 4 PWM outputs will restore to 50% brightness.
RGBgenie Single Channel Micro Controller and Lamp Module
Join instructions
- Select the Start Zigbee Pairing button.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Short press the Reset button 5 times in a row, or if the button is not accessible, power cycle the device 5 times.
RGBgenie Single Channel Trailing Edge Dimmer
Join instructions
- Select the Start Zigbee Pairing button.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Short press the Reset button 5 times in a row, or if the button is not accessible, power cycle the device 5 times.
RGBgenie Single color controller
Join instructions
- Power on the LED dimmer.
- Select the Start Z-Wave Inclusion button.
- Wait for the inclusion process to end and the device is successfully included.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the Inclusion/Exclusion button 3 times.
- The LED dimmer will be set to Exclusion mode and the connected LED light will flash quickly for 6 seconds.
- The LED light will stay ON solid for 3 seconds to indicate successful exclusion.
Factory reset instructions
- Press and hold down the Inclusion/Exclusion button for over 10 seconds.
- The connected LED light will stays ON solid for 3 seconds to indicate successful factory reset.
- Release the Inclusion/Exclusion button and all 4 PWM outputs will restore to 50% brightness.
RGBgenie Single Color Controller Panel
Join instructions
- Select the Start Zigbee Pairing button.
- Press and hold the power button until the LED status indicator turns on.
- Immediately press the S1 button once to enable the Touch Panel to search for nearby networks. The LED indicator will flash once every second.
- Wait for the pairing process to end and the device is successfully paired.
- Quickly press any button and the LED indicator should flash once indicating device was successfully paired.
- If the LED indicator does not respond, the Touch Panel is not paired with a network.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Press and hold down the power button on the Touch Panel until the LED indicator turns on.
- Immediately press the power button 5 times.
- The LED indicator will flash 3 times quickly to indicate successful removal from the network and is now reset to factory default.
RGBgenie Single Color Wall Mounted Remote Controller
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Ring Ring Alarm Contact Sensor V1
Join instructions
- Select the Start Z-Wave Inclusion button.
- Open the contact sensor cover.
- Quickly remove and replace the battery to begin the inclusion process.
- Wait for the inclusion process to end and the device is successfully included.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Open the contact sensor cover.
- Quickly remove and replace the battery to exclude the device.
Factory reset instructions
- Open the contact sensor cover.
- Remove the battery from the device.
- Press and hold the tamper switch while reinstalling the battery.
- The LED will be flashing. Keep holding the tamper switch until the LED turns off.
Ring Ring Alarm Motion Sensor V1
Join instructions
- Select the Start Z-Wave Inclusion button.
- Open the motion sensor cover.
- Quickly remove and replace the battery to begin the inclusion process.
- Wait for the inclusion process to end and the device is successfully included.
Exclude instructions
- Select the Start Z-Wave Inclusion button.
- Open the motion sensor cover.
- Quickly remove and replace the battery to exclude the device.
Factory reset instructions
- Insert a straightened paper clip into the pinhole at the back of the motion detector.
- Press and hold the Reset button.
- The LED will be flashing. Keep holding the Reset button until the LED turns off.
- Open the motion sensor cover.
- Quickly remove and replace the battery to complete factory reset of the device.
Ring Ring Alarm Range Extender V1
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press the button on the right side of the device to begin the inclusion process.
- Wait for the inclusion process to end and the device is successfully included.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the button on the right side of the device to exclude the device.
Factory reset instructions
- Plug in the Range Extender.
- Press and hold the button on the right side of the device. The LED on the device will flash rapidly.
- When the LED begins to flash slowly, release the button.
Ring Ring Alarm Smoke/CO Listener
Join instructions
- Select the Start Z-Wave Inclusion button.
- Open the Smoke/CO Listener cover.
- Quickly remove and replace the battery.
- Press the setup button on the side of the device to begin the inclusion process.
- Wait for the inclusion process to end and the device is successfully included.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Open the Smoke/CO Listener cover.
- Quickly remove and replace the battery.
- Press the setup button on the side of the device to exclude it.
Factory reset instructions
- Press and hold the Setup button on the side of the device for 10 seconds.
- When the LED stops flashing, the device has been factory reset.
Ring Ring Outdoor Siren
Join instructions
- Select the Start Z-Wave Inclusion button.
- After powering on the device, press and hold the test button under the battery cover for 3 seconds. Release the button and the device will enter Classic inclusion mode which implements both classic inclusion with a Node Information Frame, and Network Wide Inclusion. During Classic Inclusion mode, the green LED will blink 3 times followed by a brief pause, repeatedly. When Classic inclusion times-out, the device will blink alternating red and green a few times.
- Enter the 5-digit DSK when prompted.
- Wait for the inclusion process to end and the device is successfully included.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Locate the reset button on the back of the device under the battery compartment.
- With the controller in Remove (Z-Wave Exclusion) mode, use a paper clip or similar object and tap the pinhole button. The device’s red LED will turn on solid to indicate the device was excluded.
Factory reset instructions
- To restore Ring Alarm Outdoor Siren to factory default settings, locate the reset button underneath the battery cover.
- Note: Use this procedure only in the event that the network primary controller is missing or otherwise inoperable.
- Using a paperclip or similar object, insert it into the pinhole, press and hold the button down for 10 seconds.
- The device will rapidly blink green continuously for 10 seconds. After about 10 seconds, when the green blinking stops, release the button. The red LED will turn on solid to indicate the device was reset.
Rotel Rotel AVR
Join instructions
- Click the Install Device button.
- Enter the AVR's IP address in the Rotel IP preference field in the driver details, click Save Preferences.
- Turn the AVR on, then select each of the available AVR inputs on the physical device, these will appear in the driver details Current States.
- Any input's display name can be changed by selecting the desired input and clicking the Edit Current Input Name command after adding the new name in the New name field.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Sage A19 Bulb
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Sage BR30 Bulb
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Sage Doorbell Sensor
Join instructions
- Select the Start Zigbee Pairing button.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Remove the plastic cover and the battery.
- Press and hold the tiny RESET button (next to where the wires attach to the circuit board) while you reinstall the battery.
- Continue holding RESET until the red LED flashes.
Sage Light Switch Controller
Join instructions
- Select the Start Zigbee Pairing button.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Remove the battery from the light switch.
- Press and hold the rocker switch in the ON position as you reinstall the battery.
- Continue to hold the switch in the ON position until the red LED flashes.
Salus Smart Plug
Join instructions
- Select the Start Zigbee Pairing button.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Press the button on the outlet for 10 seconds.
- The light surrounding the button will flash Red 5 times, and will then go out.
Samotech Zigbee Control Module
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Samsung SmartThings Button V5
Join instructions
- Select the Start Zigbee Pairing button.
- Hold the recessed connect button for 5 seconds.
- Release the button when the LED starts flashing Red.
- The LED will flash Red and Green while attempting to connect.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Hold the recessed connect button for 5 seconds.
- Release the button when the LED starts flashing red.
Samsung SmartThings Motion Sensor V5
Join instructions
- Select the Start Zigbee Pairing button.
- Hold the recessed connect button for 5 seconds.
- Release the button when the LED starts flashing red.
- The LED will flash red and green while attempting to connect.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Hold the recessed connect button for 5 seconds.
- Release the button when the LED starts flashing red.
Samsung SmartThings Multi Sensor V5
Join instructions
- Select the Start Zigbee Pairing button.
- Hold the recessed connect button for 5 seconds.
- Release the button when the LED starts flashing red.
- The LED will flash red and green while attempting to connect.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Hold the recessed connect button for 5 seconds.
- Release the button when the LED starts flashing red.
Samsung SmartThings Outlet (2017 Model)
Join instructions
- Select the Start Zigbee Pairing button.
- Make sure the Outlet is within 15 feet (4.5 meters) of the hub during setup.
- Hold the Connect button for 5 seconds, and release it when the LED starts flashing Blue.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Hold the Connect button for 5 seconds, and release it when the LED starts flashing Blue.
Samsung SmartThings Outlet V5
Join instructions
- Select the Start Zigbee Pairing button.
- Hold the Connect button for 5 seconds, and release it when the LED flashes blue 3 times.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Hold the Connect button for 5 seconds, and release it when the LED flashes blue 3 times.
Samsung SmartThings Water Leak Sensor V5
Join instructions
- Select the Start Zigbee Pairing button.
- Hold the recessed connect button for 5 seconds.
- Release the button when the LED starts flashing red.
- The LED will flash red and green while attempting to connect.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Hold the recessed connect button for 5 seconds.
- Release the button when the LED starts flashing red.
Samsung SmartThings Zigbee Smart Plug
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Sengled Button Controller
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Sengled Element Classic Bulb
Join instructions
- Select the Start Zigbee Pairing button.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Power cycle on and off 15 times, VERY quickly, ending on the ON position.
- NOTE: An on and off cycle counts as 1.
- If successful, the bulb will flash 5 times, and will then be in pairing mode.
Sengled Element Multicolor Bulb
Join instructions
- Select the Start Zigbee Pairing button.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Power cycle on and off 15 times, VERY quickly, ending on the ON position.
- NOTE: An on and off cycle counts as 1.
- If successful, the bulb will flash 5 times, and will then be in pairing mode.
Sengled Element Plus Bulb
Join instructions
- Select the Start Zigbee Pairing button.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Power cycle on and off 15 times, VERY quickly, ending on the ON position.
- NOTE: An on and off cycle counts as 1.
- If successful, the bulb will flash 5 times, and will then be in pairing mode.
Sengled Multicolor Light Strip
Join instructions
- Select the Start Zigbee Pairing button.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Press and hold the reset button inside the unit for 10 seconds.
- If successful, the light strip will flash 5 times.
Sengled Sengled Element Classic with motion
Join instructions
- Select the Start Zigbee Pairing button.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Power cycle on and off 15 times, VERY quickly, ending on the ON position.
- NOTE: An on and off cycle counts as 1.
- If successful, the bulb will flash 5 times, and will then be in pairing mode.
Sengled Smart Plug
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Sengled Smart Plug
Join instructions
- Select the Start Zigbee Pairing button.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Press and hold the power button for 15 seconds.
- If successful blue indicator light will stay on briefly, and then slowly pulse on and off.
Sengled Smart Window and Door Sensor
Join instructions
- Select the Start Zigbee Pairing button.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- To reset the sensor, use the provided tool, or something equally thin like a paper clip.
- Press and hold the reset button inside the unit for 8 seconds.
- If successful, a red light on the face of the sensor will flash 2 times.
- NOTE: After the sensor is reset, you will have one minute to add it to your hub.
Sensative Strips Comfort
Join instructions
- Select the Start Z-Wave Inclusion button.
- Move the magnet towards the rounded edge until you see 2 LED flashes.
- Move the magnet between the logo and the rounded edge 2 times slowly.
- Remove the magnet. If you see 1 LED flash, inclusion was successful.
- If you see 5 short LED flashes, then inclusion has failed and you should perform a factory reset, then repeat the inclusion process.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Move the magnet towards the rounded edge until 1 LED flashes.
- Move the magnet between the logo and the rounded edge 2 times slowly.
- Remove the magnet. If you see 1 LED flash, it indicates successful exclusion.
- If you see 5 short LED flashes, then exclusion has failed and you should perform a factory reset, then repeat the exclusion process.
Factory reset instructions
- Place the magnet 2cm from the rounded edge for 2 seconds. You should see 1 short LED flash.
- Move between the logo and the round edge 2 times.
- On the second pass, leave the magnet there for 10 seconds and wait for 1 long LED flash.
Sensative Strips Drips
Join instructions
- Select the Start Z-Wave Inclusion button.
- Move the magnet towards the rounded edge until you see 2 LED flashes.
- Move the magnet between the logo and the rounded edge slowly 2 times.
- Remove the magnet. If you see 1 LED flash, inclusion was successful.
- If you see 5 short LED flashes, then inclusion has failed and you should perform a factory reset, then repeat the inclusion process.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Move the magnet towards the rounded edge until 1 LED flashes.
- Move the magnet between the logo and the rounded edge 2 times slowly.
- Remove the magnet. If you see 1 LED flash, it indicates successful exclusion.
- If you see 5 short LED flashes, then exclusion has failed and you should perform a factory reset, then repeat the exclusion process.
Factory reset instructions
- Place the magnet 2cm from the rounded edge for 2 seconds. You should see 1 short LED flash.
- Move between the logo and the round edge 2 times.
- On the second pass, leave the magnet there for 10 seconds and wait for 1 long LED flash.
Sensative Strips Guard
Join instructions
- Select the Start Z-Wave Inclusion button.
- Keep Strips close to its intended location during the inclusion process.
- Remove both magnets. 1 long flash confirms proper inclusion of the device.
- Move the squared magnet away from the squared end and watch the status in the device details to ensure proper functionality.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Remove both magnets. 1 long flash confirms successful exclusion of the device.
Factory reset instructions
- Move the magnet all the way to the rounded edge, You should see 1 short LED flash.
- Move the magnet towards the center 2 times. You should see 2 LED flashes.
- On the last pass, leave at rounded edge for 10 seconds.
- If successful, you should see 1 long LED flash.
- If you do not see any flashes, then the reset process was not completed successfully.
Shelly Shelly 1
Join instructions
- Click the Install Device button.
- Enter the IP address of the Shelly device in the Shelly IP address preference field in the driver details.
- Enter a user ID and password if these were configured on the shelly device, leave blank otherwise.
- Click Save Preferences.
Shelly Shelly 1PM
Join instructions
- Click the Install Device button.
- Enter the IP address of the Shelly device in the Shelly IP address preference field in the driver details.
- Enter a user ID and password if these were configured on the shelly device, leave blank otherwise.
- Click Save Preferences.
Shelly Shelly 2.5
Join instructions
- Click the Install Device button.
- Enter the IP address of the Shelly device in the Shelly IP address preference field in the driver details.
- Enter a user ID and password if these were configured on the shelly device, leave blank otherwise.
- Click Save Preferences.
Shelly Shelly Bulb
Join instructions
- Click the Install Device button.
- Enter the IP address of the Shelly device in the Shelly IP address preference field in the driver details.
- Enter a user ID and password if these were configured on the shelly device, leave blank otherwise.
- Click Save Preferences.
Shelly Shelly DUO
Join instructions
- Click the Install Device button.
- Enter the IP address of the Shelly device in the Shelly IP address preference field in the driver details.
- Enter a user ID and password if these were configured on the shelly device, leave blank otherwise.
- Click Save Preferences.
Shelly Shelly Plug
Join instructions
- Click the Install Device button.
- Enter the IP address of the Shelly device in the Shelly IP address preference field in the driver details.
- Enter a user ID and password if these were configured on the shelly device, leave blank otherwise.
- Click Save Preferences.
Shelly WiFi Dimmer
Join instructions
- Click the Install Device button.
- Enter the IP address of the Shelly device in the Shelly IP address preference field in the driver details.
- Enter a user ID and password if these were configured on the shelly device, leave blank otherwise.
- Click Save Preferences.
Shelly WiFi Switch
Join instructions
- Click the Install Device button.
- Enter the IP address of the Shelly device in the Shelly IP address preference field in the driver details.
- Enter a user ID and password if these were configured on the shelly device, leave blank otherwise.
- Click Save Preferences.
Sinopé In-Wall Outlet
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Sinopé Multi Controller
Join instructions
- Select the Start Zigbee Pairing button.
- Push the connect button.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Hold the connect button for more than 10 seconds.
Sinopé Sinope DM2550ZB Dimmer
Join instructions
- Select the Start Zigbee Pairing button.
- Press top and bottom buttons at the same time for 10 seconds.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Sinopé Smart Dimmer
Join instructions
- Select the Start Zigbee Pairing button.
- Simultaneously press the up and down dimmer buttons for 1 second.
- The LED will flash blue while connecting
- The LED with flash green when connected.
- If the LED is flashing red, the connection has failed.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Simultaneously press the up and down dimmer buttons for 10 seconds.
Sinopé Smart Double-Pole Thermostat
Join instructions
- Select the Start Zigbee Pairing button.
- Simultaneously press the UP and DOWN arrow buttons to initiate device paring.
- On the thermostat display, a radio signal icon will flash while connecting, and will remain solid once connected to the hub.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Simultaneously press the UP and DOWN arrow buttons for 10 seconds.
- On the thermostat display, the radio signal icon will disappear.
Sinopé Smart Electrical Load Controller
Join instructions
- Select the Start Zigbee Pairing button.
- Press the button next to the radio signal icon to initiate device paring.
- On the device, the LED next to the radio signal icon will flash while connecting, and will remain solid once connected to the hub.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Press the button next to the radio signal icon for 10 seconds.
- On the device, the LED next to the radio signal icon will turn off.
- All settings will be reset to factory defaults.
Sinopé Smart Floor Heating Thermostat
Join instructions
- Select the Start Zigbee Pairing button.
- Simultaneously press the UP and DOWN arrow buttons to initiate device paring.
- On the thermostat display, a radio signal icon will flash while connecting, and will remain solid once connected to the hub.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Simultaneously press the UP and DOWN arrow buttons for 10 seconds.
- On the thermostat display, the radio signal icon will disappear.
Sinopé Smart Low Voltage Thermostat
Join instructions
- Select the Start Zigbee Pairing button.
- Simultaneously press the UP and DOWN arrow buttons to initiate device paring.
- On the thermostat display, a radio signal icon will flash while connecting, and will remain solid once connected to the hub.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Simultaneously press the UP and DOWN arrow buttons for 10 seconds.
- On the thermostat display, the radio signal icon will disappear.
Sinopé Smart Plug
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Sinopé Smart Switch
Join instructions
- Select the Start Zigbee Pairing button.
- Simultaneously press the ON and OFF buttons for 1 second.
- The LED will flash blue while connecting
- The LED with flash green when connected.
- If the LED is flashing red, the connection has failed.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Simultaneously press the ON and OFF buttons for 10 seconds.
Sinopé Smart Thermostat for Electric Heating
Join instructions
- Select the Start Zigbee Pairing button.
- Simultaneously press the UP and DOWN arrow buttons to initiate device paring.
- On the thermostat display, a radio signal icon will flash while connecting, and will remain solid once connected to the hub.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Simultaneously press the UP and DOWN arrow buttons for 10 seconds.
- On the thermostat display, the radio signal icon will disappear.
Sinopé Smart thermostat for electric heating
Join instructions
- Select the Start Zigbee Pairing button.
- Simultaneously press the UP and DOWN arrow buttons to initiate device paring.
- On the thermostat display, a radio signal icon will flash while connecting, and will remain solid once connected to the hub.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Simultaneously press the UP and DOWN arrow buttons for 10 seconds.
- On the thermostat display, the radio signal icon will disappear.
Sinopé Smart Water Leak Detector
Join instructions
- Select the Start Zigbee Pairing button.
- Remove the battery cover.
- Press the Link button to initiate device paring:
- The LED will flash green while connecting.
- The LED will remain solid green for 10 seconds upon successful pairing.
- If the LED is flashing red, pairing has failed.
- Test the sensor by exposing the electrodes to a damp cloth and observing the device status on the device details page on your Hubitat Elevation™.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Remove the battery cover.
- Press the Link button for 10 seconds.
- The LED will flash green.
Sinopé Smart Water Leak Detector with Sensor
Join instructions
- Select the Start Zigbee Pairing button.
- Remove the battery cover.
- Press the Link button to initiate device paring:
- The LED will flash green while connecting.
- The LED will remain solid green for 10 seconds upon successful pairing.
- If the LED is flashing red, pairing has failed.
- Test the sensor by exposing the electrodes to a damp cloth and observing the device status on the device details page on Hubitat Elevation™.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Remove the battery cover.
- Press the Link button for 10 seconds.
- The LED will flash green.
Sinopé Smart Water Valve
Join instructions
- Select the Start Zigbee Pairing button.
- Remove the battery cover.
- Ensure the switch is set to position 3 (Zigbee connection).
- Plug the valve power adapter into an AC outlet.
- Press the A button to initiate device paring:
- The LED will flash green while connecting.
- The LED will remain solid green for 10 seconds upon successful pairing.
- If the LED is flashing red, pairing has failed.
- Test the valve by toggling Open and Close in the device detail page on Hubitat Elevation™, and observe that the valve properly opens and closes in response to the pressing to the Open and Close buttons.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Remove the battery cover.
- Ensure the switch is set to position 3 (Zigbee connection).
- Plug the valve power adapter into an AC outlet.
- Simultaneously press buttons A and B for 10 seconds.
- The LED will flash green.
Sinopé Tank Level Monitor
Join instructions
- Select the Start Zigbee Pairing button.
- Push the connect button.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Hold the connect button for more than 10 seconds.
Sinopé Water Heater Controller
Join instructions
- Select the Start Zigbee Pairing button.
- Push the connect button.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Hold the connect button for more than 10 seconds.
Sinopé Zigbee Water Valve
Join instructions
- Select the Start Zigbee Pairing button.
- Set the device mode switch to 3
- Press the A button on the device.
- The LED should blink green then turn solid for 10 seconds when connected.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Press simultaneously the A and B buttons on the smart water valve for about 15 seconds.
- Verify that the indicator lights come on. They should all be green, except for one which will appear orange.
- The valve will turn off to indicate that it has been reset.
SmartThings Arrival/Presence Sensor V4
Join instructions
- Select the Start Zigbee Pairing button.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Remove the cover and hold the Connect button for 5 seconds.
- Release the button when the LED turns off.
SmartThings Contact Sensor
Join instructions
- Select the Start Zigbee Pairing button.
- Hold the recessed connect button for 5 seconds.
- Release the button when the LED starts flashing red.
- The LED will flash red and green while attempting to connect.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Hold the recessed connect button for 5 seconds.
- Release the button when the LED starts flashing red.
SmartThings Humidity Sensor
Join instructions
- Select the Start Zigbee Pairing button.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Slide the sensor off the mount, remove the cover, and then the battery.
- While holding down the reset button, reinsert battery to factory reset the device.
SmartThings Motion Sensor V2
Join instructions
- Select the Start Zigbee Pairing button.
- Remove the cover of the Motion Sensor.
- Remove the battery, then hold the Connect button while inserting the battery.
- Release the button once the LED is lit.
- The LED will flash blue while attempting to connect.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Remove the cover of the Motion Sensor.
- Remove the battery, then hold the Connect button while inserting the battery.
- Release the button once the LED is lit.
SmartThings Motion Sensor V3
Join instructions
- Select the Start Zigbee Pairing button.
- Remove the cover of the Motion Sensor.
- Remove the battery, then hold the Connect button while inserting the battery.
- Release the button once the LED is lit.
- The LED will flash blue while attempting to connect.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Remove the cover of the Motion Sensor.
- Remove the battery, then hold the Connect button while inserting the battery.
- Release the button once the LED is lit.
SmartThings Motion Sensor V4
Join instructions
- Select the Start Zigbee Pairing button.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Remove the cover and hold the Connect button for 5 seconds.
- Release it when the LED starts flashing red.
SmartThings Multi Sensor (2015 model)
Join instructions
- Select the Start Zigbee Pairing button.
- Hold the Connect button while inserting the battery.
- Release the button once the LED is lit.
- The LED will flash blue while attempting to connect.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Hold the Connect button while inserting the battery.
- Release the button once the LED is lit.
SmartThings Multi Sensor (2016 model)
Join instructions
- Select the Start Zigbee Pairing button.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Remove the cover and hold the Connect button for 5 seconds.
- Release it when the LED starts flashing red.
SmartThings Multi Sensor V4
Join instructions
- Select the Start Zigbee Pairing button.
- Hold the Connect button while inserting the battery.
- Release the button once the LED is lit.
- The LED will flash blue while attempting to connect.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Hold the Connect button while inserting the battery.
- Release the button once the LED is lit.
SmartThings SmartSense Moisture Sensor
Join instructions
- Select the Start Zigbee Pairing button.
- Remove the cover of the Moisture Sensor.
- Remove the CR2 battery by pulling the ribbon.
- Hold the Connect button while inserting the battery.
- Release the button once the LED is lit.
- The LED will flash blue while attempting to connect.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Remove the cover of the Moisture Sensor.
- Remove the CR2 battery by pulling the ribbon.
- Hold the Connect button while inserting the battery.
- Release the button once the LED is lit.
SmartThings SmartSense Motion Sensor
Join instructions
- Select the Start Zigbee Pairing button.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Hold the Connect button for 6 seconds or until the LED light turns off.
SmartThings SmartSense Presence Sensor V2
Join instructions
- Select the Start Zigbee Pairing button.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Insert a small flathead screwdriver into the groove at the base of the SmartSense Presence Sensor.
- Gently twist the screwdriver and the plastic case should pop open.
- Hold the Connect button on the sensor for about 6 seconds until the LED light turns off, and then release.
SmartThings Water Leak Sensor v4 (2015)
Join instructions
- Select the Start Zigbee Pairing button.
- Remove the cover of the Water Leak Sensor.
- Remove the battery, then hold the Connect button while inserting the battery.
- Release the button once the LED is lit.
- The LED will flash blue while attempting to connect.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Remove the cover of the Water Leak Sensor.
- Remove the battery, then hold the Connect button while inserting the battery.
- Release the button once the LED is lit.
Sonoff S31 Lite Zigbee Smart Plug US
Join instructions
- Select the Start Zigbee Pairing button.
- Plug in the device.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- From the device's details page, select Remove Device, then Remove.
Sonoff ZBMINI Relay Module
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Sonoff Zigbee Button Controller
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Sonoff Zigbee Contact Sensor
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Sonoff Zigbee Motion Sensor
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Sonoff Zigbee Temperature/Humidity Sensor
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Sonos Media Player
Join instructions
- Click the Install App button below to install the Sonos Integration.
- Follow the online instructions beginning at step 3 here to complete setup.
Sunricher 4 Channels CV 100W Dimmable Driver
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Sunricher 4 in 1 Universal LED Controller
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Sunricher Ceiling Mount Occupancy Sensor
Join instructions
- Select the Start Zigbee Pairing button.
- Press the button or power cycle the device 5 times.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Press the button or power cycle the device 5 times.
Sunricher Dimmer controller
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Sunricher Dimmer Module
Join instructions
- Select the Start Zigbee Pairing button.
- Apply power to the device to set it into network pairing mode.
- A connected light will flash twice slowly. You have 15 seconds before timeout. Repeat the operation if you exceed the timeout period.
- A connected light will flash 5 times and then stay ON solid.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Apply power to the device to start TouchLink Commissioning. You have 180 seconds before timeout. Repeat the operation if you exceed the timeout period.
- Bring the remote or touch panel within 10 cm of the device.
- Set the remote or touch panel into Touch Reset procedure to reset the device, please refer to the corresponding remote or touch panel manual to learn how.
- There will be an indication on the remote and a connected light will flash 3 times to indicate a successful reset.
Sunricher EU Zigbee RGBW panel
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Sunricher Fixture Integrated Occupancy Sensor
Join instructions
- Select the Start Zigbee Pairing button.
- Press the button or power cycle the device 5 times.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Press the button or power cycle the device 5 times.
Sunricher IP65 Occupancy Sensor
Join instructions
- Select the Start Zigbee Pairing button.
- Press the button or power cycle the device 5 times.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Press the button or power cycle the device 5 times.
Sunricher Outlet Strip
Factory reset instructions
- From the device's details page, select Remove Device, then Remove.
Sunricher Power reporting outlet
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Sunricher Relay Module
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Press the button 5 times.
Sunricher Single color 4-Group remote
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Sunricher Single color 8 button controller
Join instructions
- Hold down the two top buttons until the LED lights up solid.
- Select the Start Zigbee Pairing button.
- Press the second button from the top, on the right side of the controller.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Hold down the two top buttons until the LED lights up solid.
- Immediately press the second button from the top, on the left side of the controller 5 times.
- The LED will flash 3 times to indicate a successful reset of the device.
Sunricher Single color remote
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Sunricher Zigbee Smart Plug
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Sylvania Smart+ 4 Button Switch
Join instructions
- Select the Start Zigbee Pairing button.
- Hold buttons 2 and 3 until the LED on the device starts flashing yellow.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Hold buttons 1 and 4 together. The LED will flash red.
- Keep holding buttons 1 and 4 until the LED on the device stops flashing.
Sylvania Smart+ A19 Dimmable
Join instructions
- Select the Start Zigbee Pairing button.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Turn the light off.
- Turn the light on for 3 seconds.
- Turn the light off.
- Repeat this cycle 5 times.
- Wait 10 seconds for the light to flash 3 times.
- Repeat these steps if the light does not flash 3 times.
Sylvania Smart+ A19 RGBW
Join instructions
- Select the Start Zigbee Pairing button.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Turn the light off.
- Turn the light on for 3 seconds.
- Turn the light off.
- Repeat this cycle 5 times.
- Wait 10 seconds for the light to flash 3 times.
- Repeat these steps if the light does not flash 3 times.
Sylvania Smart+ BR30 RGBW
Join instructions
- Select the Start Zigbee Pairing button.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Start with the Sylvania bulb in the ON position.
- Turn the bulb OFF and ON 8 times in a row, pausing for 1 second each time you turn the bulb ON or OFF.
- After the eighth time OFF, turn ON the bulb and leave it ON.
- Wait about 5 seconds.
- The BR30 bulb will flash if successfully reset.
- Repeat these steps if the light does not flash.
Sylvania Smart+ Contact and Temp Sensor
Join instructions
- Select the Start Zigbee Pairing button.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Slide the sensor off the mount, remove cover, and remove battery.
- While holding down the reset button, reinsert battery to factory reset the device.
Sylvania Smart+ Dimmer
Join instructions
- Select the Start Zigbee Pairing button.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Press and hold both the top and bottom button for 3 seconds.
Sylvania Smart+ Flex RGBW
Join instructions
- From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
- Start with the Light Strip powered ON.
- Repeat 5 times - Unplug for 1 second and then plug in for 1 second.
- On the fifth time plugging in the Light Strip, leave it plugged in.
- After about 3 seconds, the Light Strip will flash rapidly 3 times to show a successful reset and ready for pairing.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
- Start with the Light Strip powered ON.
- Repeat 5 times - Unplug for 1 second and then plug in for 1 second.
- On the fifth time plugging in the Light Strip, leave it plugged in.
- After about 3 seconds, the Light Strip will flash rapidly 3 times to show a successful reset.
Factory reset instructions
- Start with the Light Strip powered ON.
- Repeat 5 times - Unplug for 1 second and then plug in for 1 second.
- On the fifth time plugging in the Light Strip, leave it plugged in.
- After about 3 seconds, the Light Strip will flash rapidly 3 times to show a successful reset and ready for pairing.
Sylvania Smart+ Flex SL RGBW
Join instructions
- Select the Start Zigbee Pairing button.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Turn the light off.
- Turn the light on for 3 seconds.
- Turn the light off.
- Repeat this cycle 5 times.
- Wait 10 seconds for the light to flash 3 times.
- Repeat these steps if the light does not flash 3 times.
Sylvania Smart+ Motion Sensor
Join instructions
- Select the Start Zigbee Pairing button.
- Hold down the Pairing/Reset button while inserting the battery. As soon as you see the red light on the front of the sensor, release the button.
- The light on the front of the sensor will be flashing blue, indicating it is searching for a Zigbee network to join.
- When the light on the front of the sensor flashes green briefly, a network has been found and pairing with the hub will complete shortly after.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Remove the battery for at least 10 seconds.
- Hold down the Pairing/Reset button while inserting the battery. Do not release the button.
- The light on the front of the sensor will be solid red. Release the Pairing/Reset button when the light goes out.
- Remove the battery for at least 10 seconds to prepare for pairing.
Sylvania Smart+ Outdoor RGBW Flex
Join instructions
- Select the Start Zigbee Pairing button.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Turn the light off.
- Turn the light on for 3 seconds.
- Turn the light off.
- Repeat this cycle 5 times.
- Wait 10 seconds for the light to flash 3 times.
- Repeat these steps if the light does not flash 3 times.
Sylvania Smart+ Outlet
Join instructions
- Select the Start Zigbee Pairing button.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Make sure the plug is powered on. The light will be orange.
- Press the button located on the front of the plug and hold it down for 10 seconds.
- The light will flash orange when it has been reset.
Sylvania Smart+ RT5/6 RGBW
Join instructions
- Select the Start Zigbee Pairing button.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Turn the light off.
- Turn the light on for 3 seconds.
- Turn the light off.
- Repeat this cycle 5 times.
- Wait 10 seconds for the light to flash 3 times.
- Repeat these steps if the light does not flash 3 times.
Telguard Garage Door Control Switch
Join instructions
- Plug in the GDC1.
- Remove the cover of the enclosure.
- Select the Start Z-Wave Inclusion button.
- Press the Z-Wave button 1 time to include the device.
- If the device fails to include, unplug it for 10 seconds then repeat the device inclusion steps above.
- Wait for the inclusion process to end and the device is successfully included.
- Replace the cover of the enclosure.
Exclude instructions
- Plug in the GDC1.
- Remove the cover of the enclosure.
- Select the Start Z-Wave Exclusion button.
- Press the Z-Wave button 1 time to exclude the device.
Factory reset instructions
- Plug in the GDC1.
- Remove the cover of the enclosure.
- Press the Z-Wave button 1 time to reset the device.
Telldus Outlet Switch
Join instructions
- Plug in the device.
- Select the Start Z-Wave Inclusion button.
- Press the button 3 times within 1.5 seconds to enter inclusion mode.
- Wait for the inclusion process to end and the device is successfully included.
Exclude instructions
- Plug in the device
- Select the Start Z-Wave Exclusion button.
- Press the button 3 times within 1.5 seconds to enter exclusion mode.
- Wait for the exclusion process to end and the device is successfully excluded.
Factory reset instructions
- Plug in the device.
- Press and hold the button until the LED starts flashing white after approximately 6 seconds.
- Short-press the button once more.
- The device will now reset to factory defaults and the LED will flash red.
Telstra Smart Power Plug
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Third Reality Reality Switch
Join instructions
- Select the Start Zigbee Pairing button.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Press the button on the front of the device for approximately 30 seconds.
- The LED will light steady for several seconds, then it will begin to flash rapidly.
- The device has been reset and is ready for pairing.
Third Reality Third Reality door sensor
Join instructions
- Select the Start Zigbee Pairing button.
- Press the button on the device.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Press the button inside the sensor for 10 seconds.
Third Reality Third Reality motion sensor
Join instructions
- Select the Start Zigbee Pairing button.
- Press the button inside the sensor.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Press the button inside the sensor until the LED turns red.
Third Reality Third Reality Smart Blind
Join instructions
- Select the Start Zigbee Pairing button.
- Hold the Set (square) button for 5 seconds until the LED stops changing.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Hold the Set (square) button for 5 seconds until the LED stops changing.
Third Reality Third Reality Smart Button
Join instructions
- Select the Start Zigbee Pairing button.
- Insert batteries.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Press the button for more than 30 seconds until the blue LED blinks rapidly.
Third Reality Third Reality Smart Plug
Join instructions
- Select the Start Zigbee Pairing button.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Press the button until the LED flashes.
Third Reality Third Reality Switch
Join instructions
- Select the Start Zigbee Pairing button.
- Insert batteries.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Press for 5 seconds, you will see the blue LED blink quickly (nearly 2 times per 1second)
Third Reality Third Reality Temp Humidity Sensor
Join instructions
- Select the Start Zigbee Pairing button.
- Press the button on the sensor.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Press the button for more than 10 seconds.
TKB TKB Dimmer Socket
Join instructions
- Plug in the dimmer module.
- Select the Start Z-Wave Inclusion button.
- Press the ON/OFF button 3 times within 1.5 seconds to enter inclusion mode.
- Wait for the inclusion process to end and the device is successfully included.
Exclude instructions
- Plug in the dimmer module.
- Select the Start Z-Wave Exclusion button.
- Press the ON/OFF button 3 times within 1.5 seconds to enter exclusion mode.
- Wait for the exclusion process to end and the device is successfully excluded.
Factory reset instructions
- Plug in the dimmer module.
- Press the ON/OFF button 3 times within 1.5 seconds to enter inclusion mode.
- Within 3 seconds, press and hold the ON/OFF button for 5 seconds.
Tuya Smart ODM/OEM outlet
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Tuya Smart Zigbee Motion Sensor
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Tuya Smart Zigbee Touch Wall Switch (1,2,3 and 4 gang)
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Utilitech Siren
Join instructions
- Remove the battery cover.
- Select the Start Z-Wave Inclusion button.
- Press the pairing button 1 time.
- Wait for the inclusion process to end and the device is successfully included.
Exclude instructions
- Remove the battery cover.
- Select the Start Z-Wave Exclusion button.
- Press the pairing button 1 time.
- Wait for the exclusion process to end and the device is successfully excluded.
Factory reset instructions
- Remove the battery cover.
- Press the pairing button in between the batteries 8 times, 1 second apart.
Vesternet Zigbee 8 Button Wall Controller
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Vision Siren
Join instructions
- The distance between the siren and the hub is suggested to be in 1 meter ( 3 feet ) or less.
- Select the Start Z-Wave Inclusion button.
- Remove the mounting bracket and press the program button for at least 1 second and then release.
- The LED light will turn off after successful inclusion.
- If the device is not included, it will continue in auto include, attempting every 4-6 seconds for up to 4 attempts to include.
- The LED light will flash again if the siren has not been included.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Remove the mounting bracket and press the program button for at least 1 second and then release.
- The LED light will flash upon successful exclusion.
Factory reset instructions
- Factory reset is unavailable for this device. Instead, perform a general exclusion.
Vision Vision Shock Sensor
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press the program button for at least 1 second and then release.
- The LED light will turn off after inclusion.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the program button for at least 1 second and then release.
- The LED light will turn off after exclusion.
Factory reset instructions
- Push the Tamper switch while inserting the battery & holding the Tamper switch for 5 seconds
- The device will reset to the factory defaults and the LED will will remain ON solid.
- Remove the battery and re-inset it to complete the reset process.
Visonic Window/Door Sensor
Join instructions
- Select the Start Zigbee Pairing button.
- Remove the battery cover.
- Remove the battery.
- Press and hold the tamper switch while replacing the battery.
- Release the tamper switch within 4 seconds.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Remove the battery cover.
- Remove the battery.
- Press and hold the tamper switch while replacing the battery.
- Release the tamper switch within 4 seconds.
Visonic Window/Door Sensor
Join instructions
- Select the Start Zigbee Pairing button.
- Remove the battery cover.
- Remove the battery.
- Press and hold the tamper switch while replacing the battery.
- Release the tamper switch within 4 seconds.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Remove the battery cover.
- Remove the battery.
- Press and hold the tamper switch while replacing the battery.
- Release the tamper switch within 4 seconds.
Visonic Window/Door Sensor
Join instructions
- Select the Start Zigbee Pairing button.
- Remove the battery cover.
- Remove the battery.
- Press and hold the tamper switch while replacing the battery.
- Release the tamper switch within 4 seconds.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Remove the battery cover.
- Remove the battery.
- Press and hold the tamper switch while replacing the battery.
- Release the tamper switch within 4 seconds.
Wally Shutoff Valve
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Wally Wally Sensor
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
WaterCop Shutoff Valve
Join instructions
- Select the Start Z-Wave Inclusion button.
- Ensure that the status light is flashing periodically (3-4 times).
- Press the Mode button 1 time.
- The status light will stop flashing upon successful inclusion of the device.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the Mode button 1 time.
- The status light will start flashing periodically (3-4 times) indicating the device has been successfully excluded.
Factory reset instructions
- Factory reset is unavailable for this device. Instead, perform a general exclusion.
Wireless Smoke Detector
Join instructions
- Select the Start Z-Wave Inclusion button.
- Briefly press the program button on the back of the device.
- The status LED will light up for 5 seconds and then turn off upon successful inclusion of the device.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Briefly press the program button on the back of the device.
- The status LED will light up and then immediately turn off upon successful exclusion of the device.
Factory reset instructions
- Factory reset is unavailable for this device. Instead, perform a general exclusion.
Wiz Wi-Fi Wiz Connected Smart LED Light Bulb
Join instructions
- Use Wiz smartphone app to set up the bulb on the local network.
- Test bulb functionality using app.
- Click Install App button below to install Wiz integration.
- Enable Wiz integration if it is disabled.
- Click Start device discovery and wait. Integration app should find the bulb in 30 seconds or less.
Exclude instructions
Wiz integration finds all local Wiz compatible devices automatically. If a device is no longer on the network, remove it using Remove button at the bottom of device details page.
Wiz Wi-Fi Wiz Wireless Connected Smart Dimmer
Join instructions
- Use Wiz smartphone app to set up the bulb on the local network.
- Test bulb functionality using app.
- Click the Install App button below to install the Wiz integration.
- Enable Wiz integration if it is disabled.
- Click Start device discovery and wait. Integration app should find the bulb in 30 seconds or less.
Exclude instructions
Wiz integration finds all local Wiz compatible devices automatically. If a device is no longer on the network, remove it using Remove button at the bottom of device details page.
Wiz Wi-Fi Wiz Wireless Connected Smart Plug
Join instructions
- Use Wiz smartphone app to set up the bulb on the local network.
- Test bulb functionality using app.
- Click the Install App button below to install the Wiz integration.
- Enable Wiz integration if it is disabled.
- Click Start device discovery and wait. Integration app should find the bulb in 30 seconds or less.
Exclude instructions
Wiz integration finds all local Wiz compatible devices automatically. If a device is no longer on the network, remove it using Remove button at the bottom of device details page.
Xfinity Xfinity 3400-X Keypad
Join instructions
- Select the Start Zigbee Pairing button.
- Wait for the pairing process to end and the device is successfully paired.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Remove batteries from keypad.
- Press and hold the wall tamper switch while reinstalling the batteries.
- Once the keypad illuminates, release the wall tamper switch.
Yale Assure Connected
Join instructions
- Select the Start Z-Wave Inclusion button.
- Enter the master pin code and then press the button with the Gear icon on it.
- Press 7 on the keypad to enter network setup mode.
- Press 1 to include the lock.
- Wait for the inclusion process to end and the lock is successfully included.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Enter the master pin code and then press the button with the Gear icon on it.
- Press 7 on the keypad to enter network setup mode.
- Press 3 to exclude the lock.
- Wait for the exclusion process to end and the lock is successfully excluded.
Factory reset instructions
- Remove the battery cover and the batteries.
- Remove the interior escutcheon to access the reset button.
- The reset button is located beside the PCB cable connector.
- While pressing the reset button for a minimum of 3 seconds, reinstall the batteries.
- Release the reset button and replace the battery cover.
- NOTE: Upon reset, Master PIN Code creation is the only option available and must be performed prior to any other programming of the lock.
Yale Assure Keypad Deadbolt
Join instructions
- Select the Start Zigbee Pairing button.
- Enter the master pin code and then press the button with the Gear icon on it.
- Press 7 on the keypad to enter network setup mode.
- Press 1 to join the Zigbee network.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
- Enter the master pin code and then press the button with the Gear icon on it.
- Press 7 on the keypad to enter network setup mode.
- Press 3 to leave the Zigbee network.
Factory reset instructions
- Remove the battery cover and batteries.
- Remove the interior escutcheon to access the reset button.
- The reset button is located beside the PCB cable connector.
- While pressing the reset button for a minimum of 3 seconds, reinstall the batteries.
- Release reset button and replace battery cover.
- NOTE: Upon reset, Master PIN Code creation is the only option available and must be performed prior to any other programming of the lock.
Yale Conexis L1
Join instructions
- Remove the Radio Module cover, which is the top cover on the internal handle.
- Ensure that a "Z-Wave Radio Module 2” is installed in the lock.
- Select the Start Z-Wave Inclusion button.
- Press the “R” button below the Radio Module 3 times within 1.5 seconds.
- Wait for the inclusion process to end and the lock is successfully included.
- Replace the Radio Module cover.
Exclude instructions
- Remove the Radio Module cover.
- Select the Start Z-Wave Exclusion button.
- Press the “R” button below the Radio Module 3 times within 1.5 seconds.
- Wait for the exclusion process to end and the lock is successfully excluded.
- Replace the Radio Module cover.
Factory reset instructions
- Remove the Radio Module cover, which is the top cover on the internal handle.
- Ensure that a "Z-Wave Radio Module 2” is installed in the lock.
- Select the Start Z-Wave Inclusion button.
- Press the “R” button below the Radio Module 3 times within 1.5 seconds.
- Wait for the inclusion process to end and the lock is successfully included.
- Replace the Radio Module cover.
Yale Lever Lock
Join instructions
- Select the Start Zigbee Pairing button.
- Enter the master pin code and then press the button with the Gear icon on it.
- Press 7 on the keypad to enter network setup mode.
- Press 1 to join the Zigbee network.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
- Enter the master pin code and then press the button with the Gear icon on it.
- Press 7 on the keypad to enter network setup mode.
- Press 3 to leave the Zigbee network.
Factory reset instructions
- Remove the battery cover and batteries.
- Remove the interior escutcheon to access the reset button.
- The reset button is located beside the PCB cable connector.
- While pressing the reset button for a minimum of 3 seconds, reinstall the batteries.
- Release reset button and replace battery cover.
- NOTE: Upon reset, Master PIN Code creation is the only option available and must be performed prior to any other programming of the lock.
Yale Push Button Lever Lock
Join instructions
- Select the Start Zigbee Pairing button.
- Enter the master pin code and then press the button with the Gear icon on it.
- Press 7 on the keypad to enter network setup mode.
- Press 1 to pair the lock.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
- Enter the master pin code and then press the button with the Gear icon on it.
- Press 7 on the keypad to enter network setup mode.
- Press 3 to leave the Zigbee network.
Factory reset instructions
- Remove the battery cover and batteries.
- Remove the interior escutcheon to access the reset button.
- The reset button is located beside the PCB cable connector.
- While pressing the reset button for a minimum of 3 seconds, reinstall the batteries.
- Release reset button and replace battery cover.
- NOTE: Upon reset, Master PIN Code creation is the only option available and must be performed prior to any other programming of the lock.
Yale Yale Assure Lock SL
Join instructions
- Select the Start Z-Wave Inclusion button.
- Enter the master pin code and then press the button with the Gear icon on it.
- Press 7 on the keypad to enter network setup mode.
- Press 1 to include the lock.
- Wait for the inclusion process to end and the lock is successfully included.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Enter the master pin code and then press the button with the Gear icon on it.
- Press 7 on the keypad to enter network setup mode.
- Press 3 to exclude the lock.
- Wait for the exclusion process to end and the lock is successfully excluded.
Factory reset instructions
- Remove the battery cover and the batteries.
- Remove the interior escutcheon to access the reset button.
- The reset button is located beside the PCB cable connector.
- While pressing the reset button for a minimum of 3 seconds, reinstall the batteries.
- Release reset button and replace battery cover.
- NOTE: Upon reset, Master PIN Code creation is the only option available and must be performed prior to any other programming of the lock.
Yeelight Bedside Lamp
Join instructions
- Click the Install App button below to install the Yeelight Integration.
- Using the Yeelight mobile app, enable LAN Control for each Yeelight prior to starting discovery. The LAN Control option can be enabled by selecting the lower right icon in the mobile app menu for each bulb.
- Open the Hubitat Yeelight Integration setup and start bulb discovery.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
- Switch the bulb on and off 5 times in a row (2 seconds ON and 2 seconds OFF).
- The bulb will start flashing
- After 5 seconds, it will turn white, which means the bulb has been reset to factory defaults.
Factory reset instructions
- Switch the bulb on and off 5 times in a row (2 seconds ON and 2 seconds OFF).
- The bulb will start flashing
- After 5 seconds, it will turn white, which means the bulb has been reset to factory defaults.
Yeelight Ceiling 10
Join instructions
- Click the Install App button below to install the Yeelight Integration.
- Using the Yeelight mobile app, enable LAN Control for each Yeelight prior to starting discovery. The LAN Control option can be enabled by selecting the lower right icon in the mobile app menu for each bulb.
- Open the Hubitat Yeelight Integration setup and start bulb discovery.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
- Switch the bulb on and off 5 times in a row (2 seconds ON and 2 seconds OFF).
- The bulb will start flashing
- After 5 seconds, it will turn white, which means the bulb has been reset to factory defaults.
Factory reset instructions
- Switch the bulb on and off 5 times in a row (2 seconds ON and 2 seconds OFF).
- The bulb will start flashing
- After 5 seconds, it will turn white, which means the bulb has been reset to factory defaults.
Yeelight Ceiling 15
Join instructions
- Click the Install App button below to install the Yeelight Integration.
- Using the Yeelight mobile app, enable LAN Control for each Yeelight prior to starting discovery. The LAN Control option can be enabled by selecting the lower right icon in the mobile app menu for each bulb.
- Open the Hubitat Yeelight Integration setup and start bulb discovery.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
- Switch the bulb on and off 5 times in a row (2 seconds ON and 2 seconds OFF).
- The bulb will start flashing
- After 5 seconds, it will turn white, which means the bulb has been reset to factory defaults.
Factory reset instructions
- Switch the bulb on and off 5 times in a row (2 seconds ON and 2 seconds OFF).
- The bulb will start flashing
- After 5 seconds, it will turn white, which means the bulb has been reset to factory defaults.
Yeelight Ceiling 4
Join instructions
- Click the Install App button below to install the Yeelight Integration.
- Using the Yeelight mobile app, enable LAN Control for each Yeelight prior to starting discovery. The LAN Control option can be enabled by selecting the lower right icon in the mobile app menu for each bulb.
- Open the Hubitat Yeelight Integration setup and start bulb discovery.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
- Switch the bulb on and off 5 times in a row (2 seconds ON and 2 seconds OFF).
- The bulb will start flashing
- After 5 seconds, it will turn white, which means the bulb has been reset to factory defaults.
Factory reset instructions
- Switch the bulb on and off 5 times in a row (2 seconds ON and 2 seconds OFF).
- The bulb will start flashing
- After 5 seconds, it will turn white, which means the bulb has been reset to factory defaults.
Yeelight Color 6
Join instructions
- Click the Install App button below to install the Yeelight Integration.
- Using the Yeelight mobile app, enable LAN Control for each Yeelight prior to starting discovery. The LAN Control option can be enabled by selecting the lower right icon in the mobile app menu for each bulb.
- Open the Hubitat Yeelight Integration setup and start bulb discovery.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
- Switch the bulb on and off 5 times in a row (2 seconds ON and 2 seconds OFF).
- The bulb will start flashing
- After 5 seconds, it will turn white, which means the bulb has been reset to factory defaults.
Factory reset instructions
- Switch the bulb on and off 5 times in a row (2 seconds ON and 2 seconds OFF).
- The bulb will start flashing
- After 5 seconds, it will turn white, which means the bulb has been reset to factory defaults.
Yeelight color b bulb
Join instructions
- Click the Install App button below to install the Yeelight Integration.
- Using the Yeelight mobile app, enable LAN Control for each Yeelight prior to starting discovery. The LAN Control option can be enabled by selecting the lower right icon in the mobile app menu for each bulb.
- Open the Hubitat Yeelight Integration setup and start bulb discovery.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
- Switch the bulb on and off 5 times in a row (2 seconds ON and 2 seconds OFF).
- The bulb will start flashing
- After 5 seconds, it will turn white, which means the bulb has been reset to factory defaults.
Factory reset instructions
- Switch the bulb on and off 5 times in a row (2 seconds ON and 2 seconds OFF).
- The bulb will start flashing
- After 5 seconds, it will turn white, which means the bulb has been reset to factory defaults.
Yeelight ColorA
Join instructions
- Click the Install App button below to install the Yeelight Integration.
- Using the Yeelight mobile app, enable LAN Control for each Yeelight prior to starting discovery. The LAN Control option can be enabled by selecting the lower right icon in the mobile app menu for each bulb.
- Open the Hubitat Yeelight Integration setup and start bulb discovery.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
- Switch the bulb on and off 5 times in a row (2 seconds ON and 2 seconds OFF).
- The bulb will start flashing
- After 5 seconds, it will turn white, which means the bulb has been reset to factory defaults.
Factory reset instructions
- Switch the bulb on and off 5 times in a row (2 seconds ON and 2 seconds OFF).
- The bulb will start flashing
- After 5 seconds, it will turn white, which means the bulb has been reset to factory defaults.
Yeelight Mono 5
Join instructions
- Click the Install App button below to install the Yeelight Integration.
- Using the Yeelight mobile app, enable LAN Control for each Yeelight prior to starting discovery. The LAN Control option can be enabled by selecting the lower right icon in the mobile app menu for each bulb.
- Open the Hubitat Yeelight Integration setup and start bulb discovery.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
- Switch the bulb on and off 5 times in a row (2 seconds ON and 2 seconds OFF).
- The bulb will start pulsing slowly up and down.
- After 5 seconds, it will restart automatically, which means the bulb has been reset.
Factory reset instructions
- Switch the bulb on and off 5 times in a row (2 seconds ON and 2 seconds OFF).
- The bulb will start pulsing slowly up and down.
- After 5 seconds, it will restart automatically, which means the bulb has been reset to factory defaults.
Yeelight Mono Bulb
Join instructions
- Click the Install App button below to install the Yeelight Integration.
- Using the Yeelight mobile app, enable LAN Control for each Yeelight prior to starting discovery. The LAN Control option can be enabled by selecting the lower right icon in the mobile app menu for each bulb.
- Open the Hubitat Yeelight Integration setup and start bulb discovery.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
- Switch the bulb on and off 5 times in a row (2 seconds ON and 2 seconds OFF).
- The bulb will start pulsing slowly up and down.
- After 5 seconds, it will restart automatically, which means the bulb has been reset.
Factory reset instructions
- Switch the bulb on and off 5 times in a row (2 seconds ON and 2 seconds OFF).
- The bulb will start pulsing slowly up and down.
- After 5 seconds, it will restart automatically, which means the bulb has been reset to factory defaults.
Yeelight Smart LED Bulb (Color and CT)
Join instructions
- Click the Install App button below to install the Yeelight Integration.
- Using the Yeelight mobile app, enable LAN Control for each Yeelight prior to starting discovery. The LAN Control option can be enabled by selecting the lower right icon in the mobile app menu for each bulb.
- Open the Hubitat Yeelight Integration setup and start bulb discovery.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
- Switch the bulb on and off 5 times in a row (2 seconds ON and 2 seconds OFF).
- The bulb will start flashing
- After 5 seconds, it will turn white, which means the bulb has been reset to factory defaults.
Factory reset instructions
- Switch the bulb on and off 5 times in a row (2 seconds ON and 2 seconds OFF).
- The bulb will start flashing
- After 5 seconds, it will turn white, which means the bulb has been reset to factory defaults.
Yeelight Smart LED Bulb (Color)
Join instructions
- Click the Install App button below to install the Yeelight Integration.
- Using the Yeelight mobile app, enable LAN Control for each Yeelight prior to starting discovery. The LAN Control option can be enabled by selecting the lower right icon in the mobile app menu for each bulb.
- Open the Hubitat Yeelight Integration setup and start bulb discovery.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
- Switch the bulb on and off 5 times in a row (2 seconds ON and 2 seconds OFF).
- The bulb will start flashing
- After 5 seconds, it will turn white, which means the bulb has been reset to factory defaults.
Factory reset instructions
- Switch the bulb on and off 5 times in a row (2 seconds ON and 2 seconds OFF).
- The bulb will start flashing
- After 5 seconds, it will turn white, which means the bulb has been reset to factory defaults.
Yeelight Smart LED Bulb (CT)
Join instructions
- Click the Install App button below to install the Yeelight Integration.
- Using the Yeelight mobile app, enable LAN Control for each Yeelight prior to starting discovery. The LAN Control option can be enabled by selecting the lower right icon in the mobile app menu for each bulb.
- Open the Hubitat Yeelight Integration setup and start bulb discovery.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
- Switch the bulb on and off 5 times in a row (2 seconds ON and 2 seconds OFF).
- The bulb will start pulsing slowly up and down.
- After 5 seconds, it will restart automatically, which means the bulb has been reset.
Factory reset instructions
- Switch the bulb on and off 5 times in a row (2 seconds ON and 2 seconds OFF).
- The bulb will start pulsing slowly up and down.
- After 5 seconds, it will restart automatically, which means the bulb has been reset to factory defaults.
Yoolax Roller Shade
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Zemismart 2 Gang Switch
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Zemismart Zigbee Switch
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Zen Thermostat
Join instructions
- Select the Start Zigbee Pairing button.
- Press the Network button on the rear of the display 5 times.
- You should see the network icon flashing on the front of the display indicating that your ZEN thermostat is attempting to pair.
- The thermostat will indicate it is successfully paired by a solid Network icon on the front of the device.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- To do a full factory reset, which will delete all your configuration settings and your network connectivity, you need to remove the device from the wall and press the CONFIG button 20 times.
- NOTE: Performing a Factory Reset will reset your ZEN's HVAC-system configuration and all of your preferences and advanced settings changes. If you do a Factory Reset, make sure that you set your configuration code and preferences back to their correct values before replacing the display on the wall.
Zipato Siren
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press the tamper key 3 times within 1.5 seconds to enter inclusion mode.
- After successful inclusion, the LED will light up for 1 second.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the tamper key 3 times within 1.5 seconds to enter exclusion mode.
- Wait for the exclusion process to end and the device is successfully excluded.
Factory reset instructions
- Press the tamper key 4 times within 1.5 seconds, but do not release the tamper key on the 4th press.
- The LED will stay ON solid for 3 seconds and then will turn OFF.
- Within 2 seconds of the LED turning OFF, release the tamper key. If successful, the LED will turn ON for 1 second.
- If reset fails, the LED will flash once.
ZLINK In-Wall Dimmer
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press the rocker switch 1 time to include the device.
- Wait for the inclusion process to end and the device is successfully included.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the rocker switch 1 time to exclude the device.
- Wait for the exclusion process to end and the device is successfully excluded.
Factory reset instructions
- Turn on the connected lighting with the rocker.
- Quickly tap on the top of the rocker 3 times.
- Now quickly tap on the bottom of the rocker 3 times.
- When reset is successful, the light will turn off and on again.
ZLINK In-Wall Switch
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press the rocker switch 1 time to include the device.
- Wait for the inclusion process to end and the device is successfully included.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the rocker switch 1 time to exclude the device.
- Wait for the exclusion process to end and the device is successfully excluded.
Factory reset instructions
- Turn on the connected lighting with the rocker.
- Quickly tap on the top of the rocker 3 times.
- Now quickly tap on the bottom of the rocker 3 times.
- When reset is successful, the light will turn off and on again.
Zooz 4-in-1 Sensor
Join instructions
- Select the Start Z-Wave Inclusion button.
- Quickly press and release the Z-Wave button 2 times with a paperclip.
- Wait for the inclusion process to end and the device is successfully included.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Quickly press and release the Z-Wave button 2 times with a paperclip.
- Wait for the exclusion process to end and the device is successfully excluded.
Factory reset instructions
- Open the back cover to trigger the tamper switch.
- Press and release the Z-Wave button using a paperclip 10 times quickly (within 10 seconds).
- The sensor will start flashing immediately and will again flash 5 times after the 10 clicks to confirm device is reset (color depends on room temperature, it’s usually blue or yellow).
Zooz Dimmer Switch
Join instructions
- Select the Start Z-Wave Inclusion button.
- Tap the top paddle 3 times quickly.
- The LED indicator will flash to signal communication.
- Wait for the inclusion process to end and the device is successfully included.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Tap the bottom paddle 3 times quickly.
- Wait for the exclusion process to end and the device is successfully excluded.
Factory reset instructions
- Tap the upper paddle 3 times and hold on the third tap for at least 10 seconds.
- The LED indicator will flash to confirm successful reset.
Zooz Motion and Light Mini Sensor
Join instructions
- Select the Start Z-Wave Inclusion button.
- Quickly press and release the Z-Wave button on the Mini Sensor 3 times.
- The LED indicator will flash quickly to indicate successful inclusion.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Quickly press and release the Z-Wave button on the Mini Sensor 3 times.
- The LED indicator will flash quickly to indicate successful exclusion.
Factory reset instructions
- Press and hold the Z-Wave button for at least 10 seconds.
- The LED indicator flashes 1 time and it may then flash 5 times to indicate the device is reset.
Zooz Motion Sensor
Join instructions
- Bring the motion sensor within direct reach of your Z-Wave radio.
- Select the Start Z-Wave Inclusion button.
- Quickly press the Z-Wave button on the motion sensor 2 times (unlock and then lock).
- Wait for the inclusion process to end and the device is successfully included.
- Make sure the button is pushed in (locked) when you finish the process to re-enable motion detection.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Quickly press the Z-Wave button on the motion sensor 2 times (unlock and then lock).
- Wait for the exclusion process to end and the device is successfully excluded.
Factory reset instructions
- Press the Z-Wave button 6 times quickly (3 unlock-lock cycles).
Zooz Motion Sensor ZSE18
Join instructions
- Select the Start Z-Wave Inclusion button.
- Quickly press and release the Z-Wave button 4-5 times.
- Wait for the inclusion process to end and the device is successfully included.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Quickly press and release the Z-Wave button 3 times.
- Wait for the exclusion process to end and the device is successfully excluded.
Factory reset instructions
- Press and hold the Z-Wave button for at least 20 seconds.
- The LED indicator will turn on then turn on solid and will then automatically turn off.
Zooz MultiRelay
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press the Z-Wave button 5 times quickly to include the device.
- The LED indicator will flash to signal communication and remain on for 2 seconds to confirm successful inclusion.
Exclude instructions
- Bring your MultiRelay close to the hub and ensure it has power.
- Select the Start Z-Wave Exclusion button.
- Press the Z-Wave button 3 times quickly.
- Wait for the exclusion process to end and the device is successfully excluded.
Factory reset instructions
- Press the Z-Wave button 4 times quickly.
- The LED indicator will light up, then quickly press the Z-Wave button 4 times again.
- The LED indicator will flash 3 times then turn off to indicate reset was successful.
Zooz Outdoor Motion Sensor
Join instructions
- Select the Start Z-Wave Inclusion button.
- Quickly press and release the tamper switch 4-5 times.
- Wait for the inclusion process to end and the device is successfully included.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Quickly press and release the tamper switch 3 times.
- Wait for the exclusion process to end and the device is successfully excluded.
Factory reset instructions
- Press the tamper switch 4 times and hold on the fourth press for at least 5 seconds.
- The LED indicator will flash to confirm successful reset.
Zooz Power Strip
Join instructions
- Plug the Power Strip into a grounded receptacle you’re planning to use it at (it doesn’t need to be close to the hub).
- Select the Start Z-Wave Inclusion button.
- Press and release the CH1 button 3 times quickly.
- All LED indicators will start flashing upon successful inclusion.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press and release the CH1 button 3 times quickly.
- Wait for the exclusion process to end and the device is successfully excluded.
Factory reset instructions
- Plug the Power Strip into a grounded receptacle.
- Tap the CH1 button 3 times and hold on the third tap for at least 10 seconds.
- All LED indicators will flash to confirm successful reset.
Zooz Power Switch
Join instructions
- Plug the smart plug into a grounded receptacle located within 3 feet from your Z-Wave radio.
- Select the Start Z-Wave Inclusion button.
- Press and release the Z-Wave button 3 times quickly.
- The LED indicator will start flashing blue, then turn blue (on) or pink (off) once successfully included.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press and release the Z-Wave button 3 times quickly to exclude the device.
- LED indicator will flash orange.
- The LED indicator will start flashing blue, then turn blue (on) or pink (off) once successfully excluded.
Factory reset instructions
- Plug the power switch into a grounded receptacle.
- Press and hold the Z-Wave button for at least 20 seconds.
- The LED indicator will flash orange and then stay solid orange for 2 seconds to indicate successful reset and the switch will then automatically turn off.
Zooz Smart Chime
Join instructions
- Select the Start Z-Wave Inclusion button.
- Quickly press and release the Z-Wave button on the Water Sensor 3 times.
- The LED indicator will flash quickly to indicate successful inclusion.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Quickly press and release the Z-Wave button on the Water Sensor 3 times.
- The LED indicator will flash quickly to indicate successful exclusion.
Factory reset instructions
- Press and hold the Z-Wave button for at least 10 seconds until the LED indicator flashes 1 time.
Zooz Smart Plug
Join instructions
- Plug the smart plug into a grounded receptacle located within 3 feet from your Z-Wave radio.
- Select the Start Z-Wave Inclusion button.
- Press and release the Z-Wave button 3 times quickly.
- The LED indicator will flash blue upon successful inclusion.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press and release the Z-Wave button 3 times quickly to exclude the device.
- The LED indicator will flash orange.
- The LED indicator will remain solid orange for a few seconds to indicate successful exclusion.
Factory reset instructions
- Plug the smart plug into a grounded receptacle.
- Press and hold the Z-Wave button for at least 20 seconds.
- The LED indicator will stay solid yellow for 2 seconds to indicate successful reset and the plug will then automatically turn off.
Zooz Smart Switch
Join instructions
- Select the Start Z-Wave Inclusion button.
- Tap the top paddle 3 times quickly.
- The LED indicator will flash to signal communication.
- Wait for the inclusion process to end and the device is successfully included.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Tap the bottom paddle 3 times quickly.
- Wait for the exclusion process to end and the device is successfully excluded.
Factory reset instructions
- Tap the upper paddle 3 times and hold on the third tap for at least 10 seconds.
- The LED indicator will flash to confirm successful reset.
Zooz Water Sensor
Join instructions
- Select the Start Z-Wave Inclusion button.
- Quickly press and release the Z-Wave button on the Water Sensor 3 times.
- The LED indicator will flash quickly to indicate successful inclusion.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Quickly press and release the Z-Wave button on the Water Sensor 3 times.
- The LED indicator will flash quickly to indicate successful exclusion.
Factory reset instructions
- Press and hold the Z-Wave button for at least 10 seconds until the LED indicator flashes 1 time.
Zooz Water Valve
Join instructions
- Connect the valve to power.
- Select the Start Z-Wave Inclusion button.
- Quickly press the red power button on the valve control 3 times.
- Wait for the inclusion process to end and the device is successfully included.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Quickly press the red power button on the valve control 3 times.
- Wait for the exclusion process to end and the device is successfully excluded.
Factory reset instructions
- Press and hold the red power button for at least 10 seconds until the LED indicator flashes 1 time.
Zooz Zooz Dimmer Toggle
Join instructions
- Select the Start Z-Wave Inclusion button.
- Toggle the switch up 3 times quickly.
- Wait for the inclusion process to end and the device is successfully included.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Toggle the switch down 3 times quickly.
- Wait for the exclusion process to end and the device is successfully excluded.
Factory reset instructions
- Toggle the switch down 3 times and hold on the third toggle for at least 10 seconds.
Zooz Zooz Double Switch
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press the upper paddle 3 times quickly.
- The LED will flash to indicate communication with the hub and will stay on for 2 seconds to indicate successful inclusion.
Exclude instructions
- Bring your Hubitat Elevation™ hub close to the RGBW Dimmer if possible.
- Select the Start Z-Wave Exclusion button.
- Press the lower paddle 3 times quickly.
- Wait for the exclusion process to end and the device is successfully excluded.
Factory reset instructions
- Press and hold the lower paddle on the dimmer for at least 15 seconds until the LED indicators start flashing, then release.
- Immediately press and hold the upper paddle on the dimmer for at least 15 seconds.
- The LED indicators will flash again to confirm successful reset.
Zooz Zooz On/Off Toggle
Join instructions
- Select the Start Z-Wave Inclusion button.
- Toggle the switch up 3 times quickly.
- Wait for the inclusion process to end and the device is successfully included.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Toggle the switch down 3 times quickly.
- Wait for the exclusion process to end and the device is successfully excluded.
Factory reset instructions
- Toggle the switch down 3 times and hold on the third toggle for at least 10 seconds.
Zooz Zooz RGBW Dimmer
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press the Z-Wave button 3 times quickly.
- The LED will flash yellow to indicate communication with the hub.
- The LED will flash green to indicate it has been successfully included.
- If inclusion fails, the LED will flash red.
Exclude instructions
- Bring your Hubitat Elevation™ hub close to the RGBW Dimmer if possible.
- Select the Start Z-Wave Exclusion button.
- Press the Z-Wave button on the device 3 times quickly.
- The LED indicator on the RGBW Dimmer will light up in red to indicate successful exclusion.
Factory reset instructions
- Press and hold the Z-Wave button to enter reset mode.
- Release the button when the LED indicator glows yellow, then quickly press the Z-Wave button again to confirm factory reset.
- Wait a few seconds until the device resets and restarts.
- The LED indicator will light up in red when it’s ready.
Zooz Zooz S2 Dimmer
Join instructions
- Select the Start Z-Wave Inclusion button.
- Tap the top paddle 3 times quickly.
- The LED indicator will flash and will remain ON for 2 seconds to indicate successful inclusion.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Tap the bottom paddle 3 times quickly.
- Wait for the exclusion process to end and the device is successfully excluded.
Factory reset instructions
- Tap the upper paddle 3 times and hold on the third tap for at least 10 seconds.
- The LED indicator will flash to confirm successful reset.
Zooz Zooz S2 Multisiren
Join instructions
- Select the Start Z-Wave Inclusion button.
- Quickly press and release the Z-Wave button 4-5 times.
- Wait for the inclusion process to end and the device is successfully included.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Quickly press and release the Z-Wave button 3 times.
- Wait for the exclusion process to end and the device is successfully excluded.
Factory reset instructions
- Press the Z-Wave button 4 times and hold on the fourth press for at least 5 seconds.
- The LED indicator will flash to confirm successful reset.
Zooz Zooz S2 On/Off Switch
Join instructions
- Select the Start Z-Wave Inclusion button.
- Tap the top paddle 3 times quickly.
- The LED indicator will flash and will remain ON for 2 seconds to indicate successful inclusion.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Tap the bottom paddle 3 times quickly.
- Wait for the exclusion process to end and the device is successfully excluded.
Factory reset instructions
- Tap the upper paddle 3 times and hold on the third tap for at least 10 seconds.
- The LED indicator will flash to confirm successful reset.
Zooz Zooz Zen51 Dry Contact Relay
Join instructions
- Select Start Z-Wave Inclusion button
- Tap the Z-Wave button 3 times quickly
- The LED indicator will blink green to signal communication.
Exclude instructions
- Select Start Z-Wave Exclusion button
- Click the Z-Wave button on the relay 3 times quickly (the LED indicator will start blinking green)
Factory reset instructions
To reset the relay, click the Z-Wave button twice and hold it for 15 seconds (hold on the SECOND press).
Zooz Zooz Zen52 Double Relay
Join instructions
- Select Start Z-Wave Inclusion button
- Tap the Z-Wave button 3 times quickly
- The LED indicator will blink green to signal communication.
Exclude instructions
- Select Start Z-Wave Exclusion button
- Click the Z-Wave button on the relay 3 times quickly (the LED indicator will start blinking green)
Factory reset instructions
To reset the relay, click the Z-Wave button twice and hold it for 15 seconds (hold on the SECOND press).
ZWP Dimmer
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press the rocker switch 1 time to include it.
- Wait for the inclusion process to end and the device is successfully included.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the rocker switch 1 time to exclude it.
- Wait for the exclusion process to end and the device is successfully excluded.
Factory reset instructions
- Turn on the connected lighting with the rocker.
- Quickly tap on the top of the rocker 3 times.
- Now quickly tap on the bottom of the rocker 3 times.
- When reset is successful, the light will turn off and on again.
ZWP Switch
Join instructions
- Select the Start Z-Wave Inclusion button.
- Press the rocker switch 1 time to include it.
- Wait for the inclusion process to end and the device is successfully included.
Exclude instructions
- Select the Start Z-Wave Exclusion button.
- Press the rocker switch 1 time to exclude it.
- Wait for the exclusion process to end and the device is successfully excluded.
Factory reset instructions
- Turn on the connected lighting with the rocker.
- Quickly tap on the top of the rocker 3 times.
- Now quickly tap on the bottom of the rocker 3 times.
- When reset is successful, the light will turn off and on again.
Generic/Other Generic Z-Wave Acceleration Sensor
Join instructions
- Refer to the manufacturers specific instructions for this device.
- Select the Start Z-Wave Inclusion button.
Factory reset instructions
- Refer to the manufacturers specific instructions for this device.
Generic/Other Generic Z-Wave Button Controller
Join instructions
- Refer to the manufacturers specific instructions for this device.
- Select the Start Z-Wave Inclusion button.
Factory reset instructions
- Refer to the manufacturers specific instructions for this device.
Generic/Other Generic Z-Wave CentralScene Dimmer
Join instructions
- Refer to the manufacturers specific instructions for this device.
- Select the Start Z-Wave Inclusion button.
Factory reset instructions
- Refer to the manufacturers specific instructions for this device.
Generic/Other Generic Z-Wave CentralScene Switch
Join instructions
- Refer to the manufacturers specific instructions for this device.
- Select the Start Z-Wave Inclusion button.
Factory reset instructions
- Refer to the manufacturers specific instructions for this device.
Generic/Other Generic Z-Wave Contact Sensor
Join instructions
- Refer to the manufacturers specific instructions for this device.
- Select the Start Z-Wave Inclusion button.
Factory reset instructions
- Refer to the manufacturers specific instructions for this device.
Generic/Other Generic Z-Wave Dimmer
Join instructions
- Refer to the manufacturers specific instructions for this device.
- Select the Start Z-Wave Inclusion button.
Factory reset instructions
- Refer to the manufacturers specific instructions for this device.
Generic/Other Generic Z-Wave Garage Door Opener
Join instructions
- Refer to the manufacturers specific instructions for this device.
- Select the Start Z-Wave Inclusion button.
Factory reset instructions
- Refer to the manufacturers specific instructions for this device.
Generic/Other Generic Z-Wave Lock
Join instructions
- Refer to the manufacturers specific instructions for this device.
- Select the Start Z-Wave Inclusion button.
Factory reset instructions
- Refer to the manufacturers specific instructions for this device.
Generic/Other Generic Z-Wave Motion Sensor
Join instructions
- Refer to the manufacturers specific instructions for this device.
- Select the Start Z-Wave Inclusion button.
Factory reset instructions
- Refer to the manufacturers specific instructions for this device.
Generic/Other Generic Z-Wave Motion/Temperature Sensor
Join instructions
- Refer to the manufacturers specific instructions for this device.
- Select the Start Z-Wave Inclusion button.
Factory reset instructions
- Refer to the manufacturers specific instructions for this device.
Generic/Other Generic Z-Wave Outlet
Join instructions
- Refer to the manufacturers specific instructions for this device.
- Select the Start Z-Wave Inclusion button.
Factory reset instructions
- Refer to the manufacturers specific instructions for this device.
Generic/Other Generic Z-Wave Plus Button Controller
Join instructions
- Refer to the manufacturers specific instructions for this device.
- Select the Start Z-Wave Inclusion button.
Factory reset instructions
- Refer to the manufacturers specific instructions for this device.
Generic/Other Generic Z-Wave Plus Contact Sensor
Join instructions
- Refer to the manufacturers specific instructions for this device.
- Select the Start Z-Wave Inclusion button.
Factory reset instructions
- Refer to the manufacturers specific instructions for this device.
Generic/Other Generic Z-Wave Plus Dimmer
Join instructions
- Refer to the manufacturers specific instructions for this device.
- Select the Start Z-Wave Inclusion button.
Factory reset instructions
- Refer to the manufacturers specific instructions for this device.
Generic/Other Generic Z-Wave Plus Outlet
Join instructions
- Refer to the manufacturers specific instructions for this device.
- Select the Start Z-Wave Inclusion button.
Factory reset instructions
- Refer to the manufacturers specific instructions for this device.
Generic/Other Generic Z-Wave Plus Scene Dimmer
Join instructions
- Refer to the manufacturers specific instructions for this device.
- Select the Start Z-Wave Inclusion button.
Factory reset instructions
- Refer to the manufacturers specific instructions for this device.
Generic/Other Generic Z-Wave Plus Scene Switch
Join instructions
- Refer to the manufacturers specific instructions for this device.
- Select the Start Z-Wave Inclusion button.
Factory reset instructions
- Refer to the manufacturers specific instructions for this device.
Generic/Other Generic Z-Wave Plus Smoke/CO Detector
Join instructions
- Refer to the manufacturers specific instructions for this device.
- Select the Start Z-Wave Inclusion button.
Factory reset instructions
- Refer to the manufacturers specific instructions for this device.
Generic/Other Generic Z-Wave Plus Switch
Join instructions
- Refer to the manufacturers specific instructions for this device.
- Select the Start Z-Wave Inclusion button.
Factory reset instructions
- Refer to the manufacturers specific instructions for this device.
Generic/Other Generic Z-Wave Plus Thermostat
Join instructions
- Refer to the manufacturers specific instructions for this device.
- Select the Start Z-Wave Inclusion button.
Factory reset instructions
- Refer to the manufacturers specific instructions for this device.
Generic/Other Generic Z-Wave Relay
Join instructions
- Refer to the manufacturers specific instructions for this device.
- Select the Start Z-Wave Inclusion button.
Factory reset instructions
- Refer to the manufacturers specific instructions for this device.
Generic/Other Generic Z-Wave Repeater
Join instructions
- Refer to the manufacturers specific instructions for this device.
- Select the Start Z-Wave Inclusion button.
Factory reset instructions
- Refer to the manufacturers specific instructions for this device.
Generic/Other Generic Z-Wave RGBWW Controller
Join instructions
- Refer to the manufacturers specific instructions for this device.
- Select the Start Z-Wave Inclusion button.
Factory reset instructions
- Refer to the manufacturers specific instructions for this device.
Generic/Other Generic Z-Wave Shade
Join instructions
- Refer to the manufacturers specific instructions for this device.
- Select the Start Z-Wave Inclusion button.
Factory reset instructions
- Refer to the manufacturers specific instructions for this device.
Generic/Other Generic Z-Wave Smart Dimmer
Join instructions
- Refer to the manufacturers specific instructions for this device.
- Select the Start Z-Wave Inclusion button.
Factory reset instructions
- Refer to the manufacturers specific instructions for this device.
Generic/Other Generic Z-Wave Smart Switch
Join instructions
- Refer to the manufacturers specific instructions for this device.
- Select the Start Z-Wave Inclusion button.
Factory reset instructions
- Refer to the manufacturers specific instructions for this device.
Generic/Other Generic Z-Wave Smoke Detector
Join instructions
- Refer to the manufacturers specific instructions for this device.
- Select the Start Z-Wave Inclusion button.
Factory reset instructions
- Refer to the manufacturers specific instructions for this device.
Generic/Other Generic Z-Wave Smoke/CO Detector
Join instructions
- Refer to the manufacturers specific instructions for this device.
- Select the Start Z-Wave Inclusion button.
Factory reset instructions
- Refer to the manufacturers specific instructions for this device.
Generic/Other Generic Z-Wave Switch
Join instructions
- Refer to the manufacturers specific instructions for this device.
- Select the Start Z-Wave Inclusion button.
Factory reset instructions
- Refer to the manufacturers specific instructions for this device.
Generic/Other Generic Z-Wave Temperature/Humidity Sensor
Join instructions
- Refer to the manufacturers specific instructions for this device.
- Select the Start Z-Wave Inclusion button.
Factory reset instructions
- Refer to the manufacturers specific instructions for this device.
Generic/Other Generic Z-Wave Thermostat
Join instructions
- Refer to the manufacturers specific instructions for this device.
- Select the Start Z-Wave Inclusion button.
Factory reset instructions
- Refer to the manufacturers specific instructions for this device.
Generic/Other Generic Z-Wave Valve
Join instructions
- Refer to the manufacturers specific instructions for this device.
- Select the Start Z-Wave Inclusion button.
Factory reset instructions
- Refer to the manufacturers specific instructions for this device.
Generic/Other Generic Z-Wave Water Sensor
Join instructions
- Refer to the manufacturers specific instructions for this device.
- Select the Start Z-Wave Inclusion button.
Factory reset instructions
- Refer to the manufacturers specific instructions for this device.
Generic/Other Generic Zigbee Bulb
Join instructions
- Refer to the manufacturers specific instructions for this device.
- Select the Start Zigbee Pairing button.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Refer to the manufacturers specific instructions for this device.
Generic/Other Generic Zigbee Contact Sensor
Join instructions
- Refer to the manufacturers specific instructions for this device.
- Select the Start Zigbee Pairing button.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Refer to the manufacturers specific instructions for this device.
Generic/Other Generic Zigbee Contact Sensor (no temp)
Join instructions
- Refer to the manufacturers specific instructions for this device.
- Select the Start Zigbee Pairing button.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Refer to the manufacturers specific instructions for this device.
Generic/Other Generic Zigbee CT Bulb (dev)
Join instructions
- Refer to the manufacturers specific instructions for this device.
- Select the Start Zigbee Pairing button.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Refer to the manufacturers specific instructions for this device.
Generic/Other Generic Zigbee Dimmer
Join instructions
- Refer to the manufacturers specific instructions for this device.
- Select the Start Zigbee Pairing button.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Refer to the manufacturers specific instructions for this device.
Generic/Other Generic ZigBee Lock
Join instructions
- Refer to the manufacturers specific instructions for this device.
- Select the Start Zigbee Pairing button.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Refer to the manufacturers specific instructions for this device.
Generic/Other Generic Zigbee Moisture Sensor
Join instructions
- Refer to the manufacturers specific instructions for this device.
- Select the Start Zigbee Pairing button.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Refer to the manufacturers specific instructions for this device.
Generic/Other Generic Zigbee Motion Sensor
Join instructions
- Refer to the manufacturers specific instructions for this device.
- Select the Start Zigbee Pairing button.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Refer to the manufacturers specific instructions for this device.
Generic/Other Generic Zigbee Motion Sensor (no temp)
Join instructions
- Refer to the manufacturers specific instructions for this device.
- Select the Start Zigbee Pairing button.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Refer to the manufacturers specific instructions for this device.
Generic/Other Generic Zigbee Motion/Humidity Sensor
Join instructions
- Refer to the manufacturers specific instructions for this device.
- Select the Start Zigbee Pairing button.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Refer to the manufacturers specific instructions for this device.
Generic/Other Generic Zigbee Multi-Endpoint Switch
Join instructions
- Refer to the manufacturers specific instructions for this device.
- Select the Start Zigbee Pairing button.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Refer to the manufacturers specific instructions for this device.
Generic/Other Generic Zigbee Outlet
Join instructions
- Refer to the manufacturers specific instructions for this device.
- Select the Start Zigbee Pairing button.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Refer to the manufacturers specific instructions for this device.
Generic/Other Generic ZigBee RGB Light
Join instructions
- Refer to the manufacturers specific instructions for this device.
- Select the Start Zigbee Pairing button.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Refer to the manufacturers specific instructions for this device.
Generic/Other Generic ZigBee RGBW Light
Join instructions
- Refer to the manufacturers specific instructions for this device.
- Select the Start Zigbee Pairing button.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Refer to the manufacturers specific instructions for this device.
Generic/Other Generic Zigbee Switch
Join instructions
- Refer to the manufacturers specific instructions for this device.
- Select the Start Zigbee Pairing button.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Refer to the manufacturers specific instructions for this device.
Generic/Other Generic Zigbee Thermostat
Join instructions
- Refer to the manufacturers specific instructions for this device.
- Select the Start Zigbee Pairing button.
Exclude instructions
- From the device's details page, select Remove Device, then Remove.
Factory reset instructions
- Refer to the manufacturers specific instructions for this device.